Add the BCM74371 PHY ID to the list of supported chips. This is a 28nm
technology Gigabit PHY SoC.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It's Broadcom PHY simply described as single-port
RGMII 10/100/1000BASE-T PHY. It requires disabling delay skew and GTXCLK
bits.
Signed-off-by: NRafał Miłecki <rafal@milecki.pl>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

1) Use 0x%02x format for register number. This follows some other
   defines and makes it easier to distinct register from values.
2) Put register define above values and sort the values. It makes
   reading header code easier.
3) Use 0x%04x format for all values. It's about consistency with other
   values (and most of the header) not a personal preference.
4) Separate define for reading shift value with an extre empty line.
   It's user for all AUXCTL registers in a bcm54xx_auxctl_read.
Signed-off-by: NRafał Miłecki <rafal@milecki.pl>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We had two defines for the same bit (both were used with the
MII_BCM54XX_AUXCTL_SHDWSEL_MISC register).
Signed-off-by: NRafał Miłecki <rafal@milecki.pl>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Starting with commit 5b4e2900 ("net: phy: broadcom: add
bcm54xx_auxctl_read") we have a reading helper so use it and avoid code
duplication.
It also means we don't need MII_BCM54XX_AUXCTL_SHDWSEL_MISC define as
it's the same as MII_BCM54XX_AUXCTL_SHDWSEL_MISC just for reading needs
(same value shifted by 12 bits).
Signed-off-by: NRafał Miłecki <rafal@milecki.pl>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for the BCM7278 28nm process Gigabit Ethernet PHY.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Broadcom PHYs expose a number of PHY error counters: receive errors,
false carrier sense, SerDes BER count, local and remote receive errors.
Add support code to allow retrieving these error counters. Since the
Broadcom PHY library code is used by several drivers, make it possible
for them to specify the storage for the software copy of the statistics.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Broadcom's Wirespeed feature allows us to configure how auto-negotiation
should behave with fewer working pairs of wires on a cable. Add support
code for retrieving and setting such downshift counters using the
recently added ethtool downshift tunables.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The BCM54810 PHY requires some semi-unique configuration, which results
in some additional configuration in addition to the standard config.
Also, some users of the BCM54810 require the PHY lanes to be swapped.
Since there is no way to detect this, add a device tree query to see if
it is applicable.
Inspired-by: NVikas Soni <vsoni@broadcom.com>
Signed-off-by: NJon Mason <jon.mason@broadcom.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a helper function to read the AUXCTL register for the BCM54xx.  This
mirrors the bcm54xx_auxctl_write function already present in the code.
Signed-off-by: NJon Mason <jon.mason@broadcom.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This PHY has internal delays enabled after reset. This clears the
internal delay enables unless the interface specifically requests them.
Signed-off-by: NXo Wang <xow@google.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Reviewed-by: NJoel Stanley <joel@jms.id.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add the RXD-to-RXC skew (delay) time bit in the Miscellaneous Control
shadow register and a mask for the shadow selector field.

Remove a re-definition of MII_BCM54XX_AUXCTL_SHDWSEL_AUXCTL.
Signed-off-by: NXo Wang <xow@google.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Reviewed-by: NJoel Stanley <joel@jms.id.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add PHY entries for the Broadcom BCM7346 and BCM7362 chips, these are
40nm generation Ethernet PHY.

Fixes: 815717d1 ("net: phy: bcm7xxx: Remove wildcard entries")
Signed-off-by: NJaedon Shin <jaedon.shin@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a PHY entry for the Broadcom BCM7435 chips, this is a 40nm
generation Ethernet PHY which is analogous to its 7425 and 7429 counter
parts.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for the Broadcom Cygnus SoCs internal PHY's.
The PHYs are 1000M/100M/10M capable with support for 'EEE'
and 'APD' (Auto Power Down).

This driver supports the following Broadcom Cygnus SoCs:
 - BCM583XX (BCM58300, BCM58302, BCM58303, BCM58305)
 - BCM113XX (BCM11300, BCM11320, BCM11350, BCM11360)

The PHY's on these SoC's require some workarounds for
stable operation, both during configuration time and
during suspend/resume. This driver handles the
application of the workarounds.
Signed-off-by: NArun Parameswaran <arunp@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds the Broadcom phy library to consolidate common
interfaces shared by Broadcom phy's.

Moved the common interfaces to the 'bcm-phy-lib.c' and updated
the Broadcom PHY drivers to use the new APIs.
Signed-off-by: NArun Parameswaran <arunp@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Define the pseudo-PHY address (30) which is used by all Broadcom
Ethernet switches in a shared header file.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We utilize inline functions from the PHY library, make sure that we do
include phy.h in brcmphy.h in order for the code including brcmphy.h not
to have to resolve this inclusion dependency.

Fixes: 70531479 ("net: phy: broadcom: move shadow 0x1C register accessors to brcmphy.h")
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

While adding support for 7425 PHY in the 7xxx PHY driver, the ID that
was used was actually coming from an external PHY: a BCM5461x. Fix this
by using the proper ID for the internal 7425 PHY and set the
PHY_IS_INTERNAL flag, otherwise consumers of this PHY driver would not
be able to properly identify it as such.

Fixes: d068b02c ("net: phy: add BCM7425 and BCM7429 PHYs")
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Reviewed-by: NPetri Gynther <pgynther@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NAlessio Igor Bogani <alessio.bogani@elettra.eu>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

BCM7439 has an alternate PHY OUI: 0xae025080 which is to be found in
some variants of this chip.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NPetri Gynther <pgynther@google.com>
Acked-by: NFlorian Fainelli <f.fainelli@gmai.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now that we have removed the need for the PHY_BRCM_100MBPS_WAR flag, we
can remove it from the GENET driver and the broadcom shared header file.
The PHY driver checks the PHY supported bitmask instead.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The Broadcom BCM7xxx internal PHYs do not contain any useful revision
information in the low 4-bits of their MII_PHYSID2 (MII register 3)
which could allow us to properly identify them.

As a result, we need the actual hardware block integrating these PHYs:
GENET or the SF2 switch to tell us what revision they are built with. To
assist with that, add two helper macros for fetching the the PHY
revision and patch level from the struct phy_device::dev_flags.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add two new entries to the Broadcom BCM7xxx internal PHY driver for
BCM7250 and BCM7364 chips. Those chips share the usual 28nm process
Gigabit PHY sequence and require the same workarounds so far.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Broadcom started to use a new OUI for its 2013 and newer products:
D4-01-29 which translates into 0xae025000 for a 32-bits OUI, add its
definition.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

PHY_BCM_OUI_4 is missing two significant digits that actually make it an
OUI, add those missing bits so it becomes usable again for matching.

Fixes: b560a58c ("net: phy: add Broadcom BCM7xxx internal PHY driver")
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The 28nm Gigabit PHY on BCM7xxx chips comes out of reset with absolutely
no EEE capabilities, such that we would actually return that we do not
support EEE when accessing 3.20 (MDIO_PCS_EEE_ABLE) registers.

Poke through the vendor-specific C45 register to enable EEE globally at
the PHY level, and advertise supported EEE modes.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The shadow register 0x1C is used both by the BCM54xxx PHYs and the
BCM7xxx internal PHYs, move the accessors to a common location so both
drivers can use them.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 439d39a9 ("net: phy: broadcom:
extract register definitions") added a bunch of registers to brcmphy.h
but left some to broadcom.c, move all of them to the header file since
the BCM54xx and BCM7xxx PHY drivers do share all of these registers.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A wildcard entry with the 32-bits OUI 0x600d8400 was added as part of
the BCM7xxx internal PHY driver, but that entry might match other PHYs
that are not covered by this driver, so let's just remove it.

Fixes: b560a58c ("net: phy: add Broadcom BCM7xxx internal PHY driver")
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@greenl8ke.davemloft.net>

This patch adds support for the Broadcom BCM7xxx Set Top Box SoCs
internal PHYs. This driver supports the following generation of SoCs:

- BCM7366, BCM7439, BCM7445 (28nm process)
- all 40nm and 65nm (older MIPS-based SoCs)

The PHYs on these SoCs require a bunch of workarounds to operate
correctly, both during configuration time and at suspend/resume time,
the driver handles that for us.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The Broadcom BCM54xx register definitions are shared between BCM54xx and
BCM7xx internal PHYs for which we are adding support. Extract these
register definitions and put them in include/linux/brcmphy.h for use by
the BCM7xxx internal PHY driver.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

include/linux/brcmphy.h is currently not protected against double
inclusion, add ifdefs guard to fix that.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds the 5241 PHY ID to the broadcom module.
Signed-off-by: NDmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Move all PHY IDs to brcmphy.h header for completeness and unification of code.
Signed-off-by: NDmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch pushes phylib definitions out to phylib headers.  For phy
IDs, this removes some code duplication.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds code to disable the TXC and RXC reference clocks if link
is not available.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The 5785 does not use the RXC reference clock.  Turning it off is
desirable as it saves power.

By default, the 50610 enables the RXC reference clock and the 50610M
disables it.  Presumably this is one of the reasons why the hardware
architect chose one over the other.

Adding a "rx reference clock disable" flag is not the ideal way to
describe the option, as it would force the MAC using a 50610M to set
the flag.  Ideally we want the flags to represent opt-in behavior that
deviates from hardware defaults.  Furthermore, the lack of a
"disable" flag implies that the requester wants the rx reference clock
enabled, which doesn't necessarily follow.

By presenting the option as a passive statement (rx reference clock
unused) rather than a command, I hope to convey an opt-in option to
disable the rx reference clock that falls back to hardware defaults if
not set.  A secondary benefit of this is that it keeps the
intelligence about phy defaults in the broadcom module where it belongs
and allows the broadcom module more latitude should a bug arise.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Broadcom 50610M parts changed the default definitions of the RGMII mode
shadow register.  The 5785 needs the RGMII mode selection bits [4:3]
cleared.

The default value of the remaining bits in this register are zero.
Rather than unnecessarily burn an extra bit in the dev_flags member in
an attempt to enumerate all possible combinations, this patch take a
more course grained approach and labels the option as "clear all bits".
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>