We need to re-get a removable media's capacity when revalidating the
disk so that its partitions get rescanned by the block layer.
Signed-off-by: NBorislav Petkov <petkovbb@gmail.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: axboe@kernel.dk
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Make 'wt' variable signed while it can be negative during calculation.
Suggested-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NAtsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: sshtylyov@ru.mvista.com
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Call devm_ioremap() for CS0 and CS1 separetely.
And some style cleanups.
Suggested-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NAtsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: ralf@linux-mips.org
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

SHWT value is used as address valid to -CSx assertion and -CSx to -DIOx
assertion setup time, and contrarywise, -DIOx to -CSx release and -CSx
release to address invalid hold time, so it actualy applies 4 times and
so constitutes -DIOx recovery time.  Check requirement of the recovery
time and cycle time.  Also check SHWT maximum value.
Suggested-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NAtsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: ralf@linux-mips.org
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

e5318b53 ("ide: use the dma safe check for
REQ_TYPE_ATA_PC") introduced a regression which caused some ATAPI drives to
turn off DMA for REQ_TYPE_BLOCK_PC commands while burning and thus degrading
performance and ultimately causing an excessive amount of underruns.

The issue is documented also in:
http://bugzilla.kernel.org/show_bug.cgi?id=11742.
Signed-off-by: NBorislav Petkov <petkovbb@gmail.com>
Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Tested-by: NValerio Passini <valerio.passini@unicam.it>
[bart: fixup patch description per comments from Sergei Shtylyov]
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Signed-off-by: NAlexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

cirrusfb_zorro_unmap() may be called both from __devexit and (on
cleanup path) from __devinit.  So it needs to be a normal function,
same as for cirrusfb_pci_unmap()
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The file(s) below do not use LINUX_VERSION_CODE nor KERNEL_VERSION.
  drivers/leds/leds-hp-disk.c
  drivers/misc/panasonic-laptop.c

This patch removes the said #include <version.h>.
Signed-off-by: NHuang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

As it is, all instances of ->release() for files that have ->fasync()
need to remember to evict file from fasync lists; forgetting that
creates a hole and we actually have a bunch that *does* forget.

So let's keep our lives simple - let __fput() check FASYNC in
file->f_flags and call ->fasync() there if it's been set.  And lose that
crap in ->release() instances - leaving it there is still valid, but we
don't have to bother anymore.
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Inspired by Sergio Luis' similar patches, I finally found
a case which is trivial enough that spatch won't choke
on it.
Signed-off-by: NIlpo Järvinen <ilpo.jarvinen@helsinki.fi>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Correct the interrupt handler in sh4 serial device, return the correct
value and check for what is anabled in the SCSCR register. The sh7722 is
broken just sending a break using minicom.
Signed-off-by: NMichael Trimarchi <trimarchimichael@yahoo.it>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

After the recent commit to kill off SCI/SCIF special casing SH 7751R
fails to compile with CONFIG_SH_RTS7751R2D set. This is because SCSPTR1
is undefined. Take the value for SCSPTR1 from the SH7751R Group Hardware
Manual.
Signed-off-by: NMatt Fleming <mjf@gentoo.org>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

SH4-202 doesn't have SCSXX1. But it is treated so that there is SCSPTR1 in
current code. This patch add sci_rxd_in of SH4-202.
Signed-off-by: NNobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This change a name of SCSPTR used in sci_rxd_in of SH5-101.
SCSPTR is not declared and will become the error.
Signed-off-by: NNobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

As noticed by Saikiran Madugula, commit 7447ef63
("loopback: Remove rest of LOOPBACK_TSO code.") got rid of
emulate_large_send_offload() but didn't get rid of the call
site as well.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove excess kernel-doc function parameters from networking header
& driver files:

Warning(include/net/sock.h:946): Excess function parameter or struct member 'sk' description in 'sk_filter_release'
Warning(include/linux/netdevice.h:1545): Excess function parameter or struct member 'cpu' description in 'netif_tx_lock'
Warning(drivers/net/wan/z85230.c:712): Excess function parameter or struct member 'regs' description in 'z8530_interrupt'
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Move SKB trim before we lookup the socket so we don't have to
put it on failure.

Based upon an initial patch by Jarek Poplawski and suggestions
from Herbert Xu.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

libata currently imposes a UDMA5 max transfer rate and 200 sector max
transfer size for SATA devices that sit behind a pata-sata bridge. Lots
of devices have known good bridges that don't need this limit applied.
The MTRON SSD disks are such devices. Transfer rates are increased by
20-30% with the restriction removed.

So add a "blacklist" entry for the MTRON devices, with a flag indicating
that the bridge is known good.
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

5287 used to be treated as vt6420 but it didn't work.  It's new family
of controllers called vt8251 which hosts four SATA ports as M/S of the
two ATA ports.  This configuration is rather peculiar in that although
the M/S devices are on the same port, each have its own SCR (or
equivalent link status/control) registers which screws up the
port-link-device hierarchy assumed by libata.  Another controller
which falls into this category is ata_piix w/ SIDPR access.

libata now has facility to deal with this class of controllers named
slave_link.  A low level driver for such controllers can just call
ata_slave_link_init() on the respective ports and libata will handle
all the difficult parts like following up with single SRST after
hardresetting both ports.

This patch creates new controller class vt8251, implements slave_link
aware init sequence and config space based SCR access for it and moves
5287 to the new class.

This patch is based on Joseph Chan's larger patch which was created
before slave_link was implemented in libata.

  http://thread.gmane.org/gmane.linux.kernel.commits.mm/40640Signed-off-by: NTejun Heo <tj@kernel.org>
Cc: Joseph Chan <JosephChan@via.com.tw>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

In ata_tf_to_lba48(), when evaluating

	(tf->hob_lbal & 0xff) << 24

the expression is promoted to signed int (since int can hold all values
of u8).  However, if hob_lbal is 128 or more, then it is treated as a
negative signed value and sign-extended when promoted to u64 to | into
sectors, which leads to the MSB 32 bits of section getting set
incorrectly.

For example, Phillip O'Donnell <phillip.odonnell@gmail.com> reported
that a 1.5GB drive caused:

    ata3.00: HPA detected: current 2930277168, native 18446744072344861488

where 2930277168 == 0xAEA87B30 and 18446744072344861488 == 0xffffffffaea87b30
which shows the problem when hob_lbal is 0xae.

Fix this by adding a cast to u64, just as is used by for hob_lbah and
hob_lbam in the function.
Reported-by: NPhillip O'Donnell <phillip.odonnell@gmail.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Remove excess kernel-doc function parameter notation from drivers/ata/:

Warning(drivers/ata/libata-core.c:1622): Excess function parameter or struct member 'fn' description in 'ata_pio_queue_task'
Warning(drivers/ata/libata-core.c:4655): Excess function parameter or struct member 'err_mask' description in 'ata_qc_complete'
Warning(drivers/ata/ata_piix.c:751): Excess function parameter or struct member 'udma' description in 'do_pata_set_dmamode'
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Currently, the numa_node of OF-devices will be overwritten during
device_register, which simply sets the node to -1.  On cell machines,
this means that devices can't find their IOMMU, which is referenced
through the device's numa node.

Set the numa node for OF devices with no parent, and use the
lower-level device_initialize and device_add functions, so that the
node is preserved.

We can remove the call to set_dev_node in of_device_alloc, as it
will be overwritten during register.
Signed-off-by: NJeremy Kerr <jk@ozlabs.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

The link may be up already via the chip's reset strapping, or though action
of U-Boot, or from the last time the interface was brought up.  Resetting
the link causes it to go down for several seconds.  This can significantly
increase the time from power-on to DHCP completion and a device being
accessible to the network.
Signed-off-by: NTrent Piepho <tpiepho@freescale.com>
Acked-by: NAndy Fleming <afleming@freescale.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

The init_phy() function attaches to the PHY, then configures the
SerDes<->TBI link (in SGMII mode).  The TBI is on the MDIO bus with the PHY
(sort of) and is accessed via the gianfar's MDIO registers, using the
functions gfar_local_mdio_read/write(), which don't do any locking.

The previously attached PHY will start a work-queue on a timer, and
probably an irq handler as well, which will talk to the PHY and thus use
the MDIO bus.  This uses phy_read/write(), which have locking, but not
against the gfar_local_mdio versions.

The result is that PHY code will try to use the MDIO bus at the same time
as the SerDes setup code, corrupting the transfers.

Setting up the SerDes before attaching to the PHY will insure that there is
no race between the SerDes code and *our* PHY, but doesn't fix everything.
Typically the PHYs for all gianfar devices are on the same MDIO bus, which
is associated with the first gianfar device.  This means that the first
gianfar's SerDes code could corrupt the MDIO transfers for a different
gianfar's PHY.

The lock used by phy_read/write() is contained in the mii_bus structure,
which is pointed to by the PHY.  This is difficult to access from the
gianfar drivers, as there is no link between a gianfar device and the
mii_bus which shares the same MDIO registers.  As far as the device layer
and drivers are concerned they are two unrelated devices (which happen to
share registers).

Generally all gianfar devices' PHYs will be on the bus associated with the
first gianfar.  But this might not be the case, so simply locking the
gianfar's PHY's mii bus might not lock the mii bus that the SerDes setup
code is going to use.

We solve this by having the code that creates the gianfar platform device
look in the device tree for an mdio device that shares the gianfar's
registers.  If one is found the ID of its platform device is saved in the
gianfar's platform data.

A new function in the gianfar mii code, gfar_get_miibus(), can use the bus
ID to search through the platform devices for a gianfar_mdio device with
the right ID.  The platform device's driver data is the mii_bus structure,
which the SerDes setup code can use to lock the current bus.
Signed-off-by: NTrent Piepho <tpiepho@freescale.com>
CC: Andy Fleming <afleming@freescale.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

When the at91_ether driver is using a GPIO for its PHY interrupt,
be sure to request (and later, if needed, free) that GPIO.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Acoording commit aa24886e,
dma_free_coherent() need irqs enabled.

This patch fix following warning messages:

WARNING: at linux/arch/x86/kernel/pci-dma.c:376 dma_free_coherent+0xaa/0xb0()

Call Trace:
 [<ffffffff8023f80f>] warn_on_slowpath+0x5f/0x90
 [<ffffffff80496ffa>] ? __kfree_skb+0x3a/0xa0
 [<ffffffff802a4723>] ? discard_slab+0x23/0x40
 [<ffffffff8021274a>] dma_free_coherent+0xaa/0xb0
 [<ffffffff8043668f>] amd8111e_close+0x10f/0x1b0
 [<ffffffff8049f3ae>] dev_close+0x5e/0xb0
 [<ffffffff8049efa1>] dev_change_flags+0xa1/0x1e0
 [<ffffffff806b2171>] ic_close_devs+0x36/0x4e
 [<ffffffff806b29ee>] ip_auto_config+0x581/0x10f3
 [<ffffffff803a6e19>] ? kobject_add+0x69/0x90
 [<ffffffff803a698a>] ? kobject_get+0x1a/0x30
 [<ffffffff803a785b>] ? kobject_uevent+0xb/0x10
 [<ffffffff803a6c62>] ? kset_register+0x52/0x60
 [<ffffffff803a6f9b>] ? kset_create_and_add+0x6b/0xa0
 [<ffffffff804e2e74>] ? tcp_ca_find+0x24/0x50
 [<ffffffff806b246d>] ? ip_auto_config+0x0/0x10f3
 [<ffffffff8020903c>] _stext+0x3c/0x150
 [<ffffffff802772d3>] ? register_irq_proc+0xd3/0xf0
 [<ffffffff802f0000>] ? mb_cache_create+0x80/0x1f0
 [<ffffffff80688693>] kernel_init+0x141/0x1b8
 [<ffffffff80688552>] ? kernel_init+0x0/0x1b8
 [<ffffffff8020d609>] child_rip+0xa/0x11
 [<ffffffff80688552>] ? kernel_init+0x0/0x1b8
 [<ffffffff80688552>] ? kernel_init+0x0/0x1b8
 [<ffffffff8020d5ff>] ? child_rip+0x0/0x11
Signed-off-by: NChunbo Luo <chunbo.luo@windriver.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Commit 401c0aab introduced a regression
in the atl1 driver by storing the VLAN tag in the wrong TX descriptor
field.

This patch causes the VLAN tag to be stored in its proper location.
Tested-by: NRamon Casellas <ramon.casellas@cttc.es>
Signed-off-by: NJay Cliburn <jacliburn@bellsouth.net>
Cc: stable@kernel.org
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Use mmiowb() to ensure "stop" and "go" commands are sent in order on ia64.
Signed-off-by: NBrice Goglin <brice@myri.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

A panic was discovered with bonding when using mode 5 or 6 and trying to
remove the slaves from the bond after the interface was taken down.
When calling 'ifconfig bond0 down' the following happens:

    bond_close()
        bond_alb_deinitialize()
            tlb_deinitialize()
		kfree(bond_info->tx_hashtbl)
                bond_info->tx_hashtbl = NULL

Unfortunately if there are still slaves in the bond, when removing the
module the following happens:

    bonding_exit()
        bond_free_all()
            bond_release_all()
                bond_alb_deinit_slave()
                    tlb_clear_slave()
                        tx_hash_table = BOND_ALB_INFO(bond).tx_hashtbl
			u32 next_index = tx_hash_table[index].next

As you might guess we panic when trying to access a few entries into the
table that no longer exists.

I experimented with several options (like moving the calls to
tlb_deinitialize somewhere else), but it really makes the most sense to
be part of the bond_close routine.  It also didn't seem logical move
tlb_clear_slave around too much, so the simplest option seems to add a
check in tlb_clear_slave to make sure we haven't already wiped the
tx_hashtbl away before searching for all the non-existent hash-table
entries that used to point to the slave as the output interface.
Signed-off-by: NAndy Gospodarek <andy@greyhouse.net>
Signed-off-by: NJay Vosburgh <fubar@us.ibm.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

This patch reworks the resource free logic performed at the time
a bonding device is released.  This (a) closes two resource leaks, one
for workqueues and one for multicast lists, and (b) improves commonality
of code between the "destroy one" and "destroy all" paths by performing
final free activity via destructor instead of explicitly (and differently)
in each path.

"Sean E. Millichamp" <sean@bruenor.org> reported the workqueue
leak, and included a different patch.
Signed-off-by: NJay Vosburgh <fubar@us.ibm.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

During the rework of the mii monitor for:

  commit f0c76d61
  Author: Jay Vosburgh <fubar@us.ibm.com>
  Date:   Wed Jul 2 18:21:58 2008 -0700

    bonding: refactor mii monitor

I left out the increment of the link failure counter.  This
patch corrects that omission.
Signed-off-by: NJay Vosburgh <fubar@us.ibm.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

When we close we must clear the extra reference we got when we read
port->tty. Setting the port tty NULL will clear the kref held by the driver
but not the one we obtained ourselves while doing the lookup.
Signed-off-by: NAlan Cox <alan@redhat.com>
Tested-by: NHelge Hafting <helge.hafting@aitel.hist.no>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The ipmi_devintf module contains the userspace interface for IPMI devices,
yet will not be loaded automatically with a system interface handler
driver.

Add a MODULE_ALIAS for the "platform:ipmi_si" MODALIAS exported by the
ipmi_si driver, so that userspace knows of the recommendation.
Signed-off-by: NScott James Remnant <scott@ubuntu.com>
Cc: Tim Gardner <tcanonical@tpi.com>
Cc: Corey Minyard <minyard@acm.org>
Cc: <stable@kernel.org>		[2.6.27.x, maybe earlier?]
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix deadlock in fb_compat_ioctl.  fb_compat_ioctl acquires a mutex and
calls fb_ioctl that tries to acquire that mutex too.  A regression added
during BKL removal.
Signed-off-by: NMikulas Patocka <mpatocka@redhat.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

tAdd adds device_init_wakeup() ivokation to probe function of
s3c2410_rtc_driver.  Without of this wakealarm sysfs attribute does not
initialise.
Signed-off-by: NYauhen Kharuzhy <jekhor@gmail.com>
Acked-by: NBen Dooks <ben-linux@fluff.org>
Acked-by: NAlessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

When ds3234 is built-in, the final links fails with the following vague error
message:

`.exit.text' referenced in section `.data' of drivers/built-in.o: defined in discarded section `.exit.text' of drivers/built-in.o

ds3234_remove() cannot be marked __exit, as it's accessed via __devexit_p().
In addition, mark ds3234_probe() __devinit while we're at it.
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Acked-by: NAlessandro Zummo <a.zummo@towertech.it>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>