Tegra210 PLLX uses the same sequences than then PLLC instances. So there
is no need to have a special registration function and ops struct for it.
Simplify the code by changing all references to the Tegra210 PLLX
registration function to the Tegra210 PLLC registration function and
avoid duplicate functionality.

Based on work by Alex Frid <afrid@nvidia.com>
Signed-off-by: NPeter De Schrijver <pdeschrijver@nvidia.com>
Tested-by: NThierry Reding <treding@nvidia.com>
Acked-by: NThierry Reding <treding@nvidia.com>
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>

If the PLL is on, only warn if the defaults are not yet set. Otherwise be
silent.
Signed-off-by: NPeter De Schrijver <pdeschrijver@nvidia.com>
Reviewed-by: NTimo Alho <talho@nvidia.com>
Tested-by: NThierry Reding <treding@nvidia.com>
Acked-by: NThierry Reding <treding@nvidia.com>
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>

Increase delay after PLL IDDQ release to 5us per PLL specifications.

based on work by Alex Frid <afrid@nvidia.com>
Signed-off-by: NPeter De Schrijver <pdeschrijver@nvidia.com>
Tested-by: NThierry Reding <treding@nvidia.com>
Acked-by: NThierry Reding <treding@nvidia.com>
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>

I2C controllers are also on the APB bus and therefor need this flag to handle
resets correctly.
Signed-off-by: NAlex Frid <afrid@nvidia.com>
Reviewed-by: NPeter De Schrijver <pdeschrijver@nvidia.com>
Tested-by: NThierry Reding <treding@nvidia.com>
Acked-by: NThierry Reding <treding@nvidia.com>
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>

Don't take the fractional part into account to calculate the effective
NDIV if fractional ndiv is not enabled.
Signed-off-by: NAlex Frid <afrid@nvidia.com>
Signed-off-by: NPeter De Schrijver <pdeschrijver@nvidia.com>
Tested-by: NThierry Reding <treding@nvidia.com>
Acked-by: NThierry Reding <treding@nvidia.com>
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>

Not all fields are read from the hw depending on the PLL type. Make sure
the other fields are 0 by clearing the structure beforehand to prevent
users such as the rate re-calculation code from using bogus values.

Based on work by  Alex Frid <afrid@nvidia.com>
Signed-off-by: NPeter De Schrijver <pdeschrijver@nvidia.com>
Tested-by: NThierry Reding <treding@nvidia.com>
Acked-by: NThierry Reding <treding@nvidia.com>
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>

Signed-off-by: NPeter De Schrijver <pdeschrijver@nvidia.com>
Tested-by: NThierry Reding <treding@nvidia.com>
Acked-by: NThierry Reding <treding@nvidia.com>
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>

PLLD2 is used for HDMI which does not allow Spread Spectrum clocking.
Signed-off-by: NPeter De Schrijver <pdeschrijver@nvidia.com>
Tested-by: NThierry Reding <treding@nvidia.com>
Acked-by: NThierry Reding <treding@nvidia.com>
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>

Make sure the pll_ss ops are compiled even when only building for Tegra210.
Signed-off-by: NPeter De Schrijver <pdeschrijver@nvidia.com>
Reviewed-by: NShreshtha Sahu <ssahu@nvidia.com>
Tested-by: NShreshtha Sahu <ssahu@nvidia.com>
Reviewed-by: NJon Mayo <jmayo@nvidia.com>
Tested-by: NThierry Reding <treding@nvidia.com>
Acked-by: NThierry Reding <treding@nvidia.com>
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>

PLL SS was only controlled when setting the PLL rate, not when the PLL itself
is enabled or disabled.
Signed-off-by: NPeter De Schrijver <pdeschrijver@nvidia.com>
Reviewed-by: NJon Mayo <jmayo@nvidia.com>
Tested-by: NThierry Reding <treding@nvidia.com>
Acked-by: NThierry Reding <treding@nvidia.com>
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>

The clock bimc_gpu_clk_src is incorrectly set to use the shared rcg2
ops, which are for RCGs with child branches controlled by different
CPUs.

The result of the incorrect ops is that the GPU's PM runtime may leave
this clock set at a very low rate. Fix this issue by using the correct
rcg2 ops.

Fixes: a2e8272f ("clk: qcom: Add MSM8916 gpu clocks")
Signed-off-by: NGeorgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>

Make these const as they are only stored in the const field of a
clk_init_data structure.
Signed-off-by: NBhumika Goyal <bhumirks@gmail.com>
Acked-by: NTero Kristo <t-kristo@ti.com>
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>

Silence the sparse warning

clk/rockchip/clk.c:172:6: warning: symbol 'rockchip_fractional_approximation' was not declared. Should it be static?

Cc: Elaine Zhang <zhangqing@rock-chips.com>
Cc: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>

The source clock ordering is wrong, as shown in the TRM:
cru_sel24_con[8]
rmii_extclk_sel
clock source select control register
1'b0: from internal PLL
1'b1: from external IO
Signed-off-by: NElaine Zhang <zhangqing@rock-chips.com>
Reviewed-by: NDavid Wu <david.wu@rock-chips.com>
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>

This MAC has no internal phy for rv1108 and the whole clock
infrastructure hasn't been used yet, so is safe to fix.
Signed-off-by: NElaine Zhang <zhangqing@rock-chips.com>
Reviewed-by: NDavid Wu <david.wu@rock-chips.com>
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>

Add gmac aclk and pclk clock gates.
Signed-off-by: NElaine Zhang <zhangqing@rock-chips.com>
Reviewed-by: NDavid Wu <david.wu@rock-chips.com>
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>

In some special circumstances, may be need to reparent clk for sclk_sdio_src.
Signed-off-by: NElaine Zhang <zhangqing@rock-chips.com>
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>

Allwinner R40 SoC have a clock controller module in the style of the
SoCs beyond sun6i, however, it's more rich and complex.

Add support for it.
Signed-off-by: NIcenowy Zheng <icenowy@aosc.io>
Signed-off-by: NChen-Yu Tsai <wens@csie.org>

This patch adds USB3.0-IF0 clock for R8A7796 SoC.
Signed-off-by: NHiromitsu Yamasaki <hiromitsu.yamasaki.ym@renesas.com>
Signed-off-by: NTakeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>

R-Car USB 2.0 controller can change the clock source from an oscillator
to an external clock via a register. So, this patch adds support
the clock source selector as a clock driver.
Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>

Add R-Car D3 (R8A77995) Clock Pulse Generator / Module Standby and
Software Reset support, using the CPG/MSSR driver core and the common
R-Car Gen3 CPG code.

Based on the R-Car Series, 3rd Generation Hardware User's Manual, Rev.
0.55, Jun. 30, 2017.
Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Acked-by: NStephen Boyd <sboyd@codeaurora.org>
Acked-by: NRob Herring <robh@kernel.org>

On R-Car Gen3 SoCs with a Spread Spectrum Clock Generator (e.g. R-Car
D3), a peripheral clock divider has been added, to select between clean
and spread spectrum parents.

Add a new clock type to the R-Car Gen3 driver core to handle this.
To avoid increasing the size of struct cpg_core_clk, both parents and
dividers are stored in the existing parent resp. div fields.
Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Acked-by: NStephen Boyd <sboyd@codeaurora.org>

On some R-Car Gen3 SoCs (e.g. R-Car D3), PLL1 and PLL3 use a divider
value different from one.  Extend struct rcar_gen3_cpg_pll_config to handle
this.  As all multipliers and dividers are small, table size increase
can be kept limited by storing them in u8s instead of unsigned ints,
which saves ca. 0.5 KiB for a generic kernel.
Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Acked-by: NStephen Boyd <sboyd@codeaurora.org>

SATA PLL on Allwinner R40 is of type (parent) * N * K / M / 6 where 6 is
the fixed post-divider.

Add post-divider support for NKM type clock.
Signed-off-by: NIcenowy Zheng <icenowy@aosc.io>
[wens@csie.org: Fixed application of post-divider in set_rate callback]
Signed-off-by: NChen-Yu Tsai <wens@csie.org>

SATA clock on sun4i/sun7i is of type (parent) / M / 6 where
6 is fixed post-divider.
Signed-off-by: NPriit Laes <plaes@plaes.org>
Signed-off-by: NIcenowy Zheng <icenowy@aosc.io>
Signed-off-by: NChen-Yu Tsai <wens@csie.org>

The CLK_SET_RATE_PARENT flag is added to clocks between the EPLL
and the audio subsystem clock controller so that the EPLL's output
frequency can be set indirectly with clk_set_rate() on a leaf clock.
That should be safe as EPLL is normally only used to generate clock
for the audio subsystem.
With this change we can avoid passing the EPLL clock to the ASoC
machine driver.
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>

This allows clk rate propagation up to the clock tree so EPLL
can be reprogrammed indirectly when setting rate of the Audio
Subsystem clocks.
The advantage is that sound machine driver can operate only
on the leaf clocks rather than explicitly re-configuring
the root clock (EPLL).
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>

Parent clock of the MAU_EPLL gate clock on exynos5422 is
"mout_user_mau_epll", not "mout_mau_epll_clk". This change
only affects exynos5422/5800.
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>

>From Rockchips fractional divider description:
  3.1.9  Fractional divider usage
  To get specific frequency, clocks of I2S, SPDIF, UARTcan be generated by
  fractional divider. Generally you must set that denominator is 20 times
  larger than numerator to generate precise clock frequency. So the
  fractional divider applies only to generate low frequency clock like
  I2S, UART.

Therefore add a special approximation function that handles this
special requirement.
Signed-off-by: NElaine Zhang <zhangqing@rock-chips.com>
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>

Fractional dividers may have special requirements concerning numerator
and denominator selection that differ from just getting the best
approximation.

For example on Rockchip socs the denominator must be at least 20 times
larger than the numerator to generate precise clock frequencies.

Therefore add the ability to provide custom approximation functions.
Signed-off-by: NElaine Zhang <zhangqing@rock-chips.com>
Acked-by: NStephen Boyd <sboyd@codeaurora.org>
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>

rk3128 and rk3126 have some gate registers describe differences.
So need to make some distinctions.
The RK3126 and RK3128 Same clock description we move it to
the common clock branches.
And the different clks description use the own clock branches.
Signed-off-by: NElaine Zhang <zhangqing@rock-chips.com>
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>

the bus/periph/nclk_ddrupctl/pclk_ddrmon/pclk_acodecphy/pclk_pmu
no driver to handle them,
Chip design requirements for these clock to always on.
Signed-off-by: NElaine Zhang <zhangqing@rock-chips.com>
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>

Rename some of clks to keep the consistency with the TRM.
Signed-off-by: NElaine Zhang <zhangqing@rock-chips.com>
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>

1. fix up the parent name
2. remove the CLK_IGNORE_UNUSED flag for some clk not need to always on.
3. fix up some clks regs describe error.
Signed-off-by: NElaine Zhang <zhangqing@rock-chips.com>
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>

Add the description of the missing clock,
make the clock more complete.
Signed-off-by: NElaine Zhang <zhangqing@rock-chips.com>
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>

fix up the lock_shift describe error.
remove the ROCKCHIP_PLL_SYNC_RATE flag for gpll.
Signed-off-by: NElaine Zhang <zhangqing@rock-chips.com>
Signed-off-by: NAndy Yan <andy.yan@rock-chips.com>
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>

fix up the cpuclk rates table for support more freqs.
fix up the mux_core_mask describe error.
Signed-off-by: NElaine Zhang <zhangqing@rock-chips.com>
Signed-off-by: NAndy Yan <andy.yan@rock-chips.com>
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>

The CEC 32K AO Clock is a dual divider with dual counter to provide a more
precise 32768Hz clock for the CEC subsystem from the external xtal.
Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com>

Switch the aoclk driver to use the new bindings and switch all the
registers access to regmap only.
Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com>

Input source 0 of the mmc controllers is not directly xtal, as currently
described in DT. Each controller is fed by a composite clock (the usual
mux, divider and gate). The muxes inputs are the xtal (default) and the
fclk_div clocks. These parents, along with the divider, should be able to
provide the necessary rates for mmc and nand operation.

The input muxes should also be able to take mpll2, mpll3 and gp0_pll but
these are precious clocks, needed for other usage. It is better if the
mmc does not use these them. For this reason, mpll2, mpll3 and gp0_pll is
not listed among the possible parents.
Signed-off-by: NJerome Brunet <jbrunet@baylibre.com>
Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com>