This is useful for userspace utilities which wish to use the previous
interface, specifically for micromanaging the increase/decrease steps by
setting min == max.
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NBen Widawsky <ben@bwidawsk.net>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Provide a standardized sysfs interface for setting min, and max
frequencies.  The code which reads the limits were lifted from the
debugfs files. As a brief explanation, the limits are similar to the CPU
p-states. We have 3 states:

RP0 - ie. max frequency
RP1 - ie. "preferred min" frequency
RPn - seriously lowest frequency

Initially Daniel asked me to clamp the writes to supported values, but
in conforming to the way the cpufreq drivers seem to work, instead
return -EINVAL (noticed by Jesse in discussion).
The values can be used by userspace wishing to control the limits of the
GPU (see the CC list for people who care).

v4: Make exceeding the soft limits return -EINVAL as well (Daniel)

v3: bug fix (Ben) -  was passing the MHz value to gen6_set_rps instead of
the step value. To fix, deal only with step values by doing the divide
at the top.

v2: add the dropped mutex_unlock in error cases (Chris)
EINVAL on both too min, or too max (Daniel)

v2 Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
CC: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NBen Widawsky <ben@bwidawsk.net>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This has been tons of fun to figure out with git blame. The first
notion of this code block goes back to the original cpu edp enabling
for ilk in

commit 32f9d658
Author: Zhenyu Wang <zhenyuw@linux.intel.com>
Date:   Fri Jul 24 01:00:32 2009 +0800

    drm/i915: Add eDP support on IGDNG mobile chip

Two things are notable in this commit wrt to the this edp special
case:
- The IS_eDP check _only_ fires for DP A, i.e. cpu edp ports.
- The cpu edp port is disabled at the top of the dp_link_down function.

My theory is that these hacks was added to work around the completely
different modeset sequence for cpu edp ports compared to pch edp
ports. With the cpu edp confusion on ilk (and snb/ivb) now fixed up,
this shouldn't be required any more.

The really interesting question is how this special cases survived
this long in the code. The first step is declaring the pch port D as
eDP if it's used for an internal panel:

commit b329530c
Author: Adam Jackson <ajax@redhat.com>
Date:   Fri Jul 16 14:46:28 2010 -0400

    drm/i915/dp: Correctly report eDP in the core connector type

This commit unfortunately failed to notice that not all edp ports are
created equal. Then follow a flurry of refactorings, culminating in a
patch from Keith Packard which resulted in the current logic (by
making it "correct" for all platforms that have edp):

commit 417e822d
Author: Keith Packard <keithp@keithp.com>
Date:   Tue Nov 1 19:54:11 2011 -0700

    drm/i915: Treat PCH eDP like DP in most places

None of these cleanups or refactorings supply any reason why we need
this code, they've simply carried it on as-is.

Hence presume it might be harmful with the current code and rip it
out. We do rewrite the link training bits completely anyway when
re-training the link.
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The exec_list is of type drm_i915_gem_exec_object2 and so casting it to
a drm_i915_gem_relocation_entry is very confusing!
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This is rather a hack to fix brightness hotkeys on a Clevo laptop. CADL is not
used anywhere in the driver code at the moment, but it could be used in BIOS as
is the case with the Clevo laptop.

The Clevo B7130 requires the CADL field to contain at least the ID of
the LCD device. If this field is empty, the ACPI methods that are called
on pressing brightness / display switching hotkeys will not trigger a
notification. As a result, it appears as no hotkey has been pressed.

Reference: https://bugs.freedesktop.org/show_bug.cgi?id=45452Tested-by: NPeter Wu <lekensteyn@gmail.com>
Signed-off-by: NPeter Wu <lekensteyn@gmail.com>
Acked-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

See bspec, Vol3 Part2, Section 1.1.3 "Display Mode Set Sequence". This
applies to all platforms where we currently support eDP on, i.e. ilk,
snb & ivb.

Without this change we fail to light up the eDP port on previously
unused crtcs (likely because something is stuck on the old pipe), and
we also fail to properly disable the old pipe (i.e. bit 30 in the
PIPECONF register is stuck as set until the next reboot).

v2: Rebased on top of the edp panel off sequence changes in 3.6-rc2.
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=44001Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

These have been added because dp links are fiddle things and don't
like it when we try to re-train an enabled output (or disable a
disabled output harder). And because the crtc helper code is
ridiculously bad add tracking the modeset state.

But with the new code in place it is simply a bug to disable a disabled
encoder or to enable an enabled encoder again. Hence convert these to
WARNs (and bail out for safety), but flatten all conditionals in the
code itself.
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

With the previous patch to clean up where exactly these two functions
are getting called, this patch can tackle the enable/disable code
itself:

- WARN if the port enable bit is in the wrong state or if the edp pll
  bit is in the wrong state, just for paranoia's sake.
- Don't disable the edp pll harder in the modeset functions just for
  fun.
- Don't set the edp pll enable flag in intel_dp->DP in modeset, do
  that while changing the actual hw state. We do the same with the
  actual port enable bit, so this is a bit more consistent.
- Track the current DP register value when setting things up and add
  some comments how intel_dp->DP is used in the disable code.

v2: Be more careful with resetting intel_dp->DP - otherwise dpms
off->on will fail spectacularly, becuase we enable the eDP port when
we should only enable the eDP pll.
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

By using the new pre_enable/post_disable functions.

To ensure that we only frob the cpu edp pll while the pipe is off add
the relevant asserts. Thanks to the new output state staging, this is
now really easy.

With this fixed we can now finally rip out the special-case handling
in the dp dpms code and replace it by the common intel_connector_dpms.
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The cpu eDP encoder has some horrible hacks to set up the DP pll at
the right time. To be able to move them to the right place, add some
more encoder callbacks so that this can happen at the right time.

LVDS has some similar funky hacks, but that would require more work
(we need to move around the pll setup a bit). Hence for now only
wire these new callbacks up for ilk+ - we only have cpu eDP on these
platforms.

v2: Bikeshed the vtable ordering, requested by Chris Wilson.
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

It's bogus.

If I've followed the history of this piece of code correctly, i.e. the
initial register write with the following vblank wait, this goes all
the way back to the original enabling of DP support in

commit a4fc5ed6
Author: Keith Packard <keithp@keithp.com>
Date:   Tue Apr 7 16:16:42 2009 -0700

    drm/i915: Add Display Port support

Unfortunately it seems to be nothing more than glorified duct-tape and
sometimes actively harmful. Adam Jackson noticed this for CPT
platforms with

commit e8519464
Author: Adam Jackson <ajax@redhat.com>
Date:   Thu Jul 21 17:48:38 2011 -0400

    drm/i915/dp: Don't turn CPT DP ports on too early

Unfortunately this kept the code around for ilk and gm45.

The specific failure case I'm seeing here is that after a dpms off/on
cycle we have the bits from the last link training (hopefully
successful link training) set in intel_dp->DP. This is requiered so
that complete_link_train can enable the port with the right tuning
values.

Unfortunately writing these again to the disabled port at dpms on time
kills the port somehow until it's disabled - dp link training fails in
an endless loop without this patch on my mobile ilk and gm45.

Cc: Chris Wilson <chris@chris-wilson.co.uk>
Tested-by: NChris Wilson <chris@chris-wilson.co.uk>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=51493Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

With the new "standardized" sysfs interfaces we need to be a bit more
careful about setting the RPS values.

Because the sysfs code and the rps workqueue can run at the same time,
if the sysfs setter wins the race to the mutex, the workqueue can come
in and set a value which is out of range (ie. we're no longer protecting
by RPINTLIM).

I was not able to actually make this error occur in testing.
Signed-off-by: NBen Widawsky <ben@bwidawsk.net>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

In order to keep our cached values in sync with the hardware, we need a
posting read here.

CC: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NBen Widawsky <ben@bwidawsk.net>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Userspace applications such as PowerTOP are interesting in being able to
read the current GPU frequency. The patch itself sets up a generic array
for gen6 attributes so we can easily add other items in the future (and
it also happens to be just about the cleanest way to do this).

The patch is a nice addition to
commit 1ac02185dff3afac146d745ba220dc6672d1d162
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date:   Thu Aug 30 13:26:48 2012 +0200

    drm/i915: add a tracepoint for gpu frequency changes

Reading the GPU frequncy can be done by reading a file like:
/sys/class/drm/card0/render_frequency_mhz
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NBen Widawsky <ben@bwidawsk.net>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Magic numbers are bad mmmkay. In this case in particular the value is
especially weird because the docs say multiple things. We'll need this
value for sysfs, so extracting it is useful for that as well.
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NBen Widawsky <ben@bwidawsk.net>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Name variables a bit better for copy-pasters. This got turned up as part
of review for upcoming sysfs patches.
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NBen Widawsky <ben@bwidawsk.net>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
[danvet: resolved conflicts due to missing some earlier patches.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Because declaring a variable in the beginning of the function, then
initializing it 100 lines later, then using it 100 lines later does
not make our code look good IMHO.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Because ironlake_crtc_mode_set is a giant function that used to have
404 lines. Let's try to make it less complex/confusing.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Rather than have multiple data structures for describing our page layout
in conjunction with the array of pages, we can migrate all users over to
a scatterlist.

One major advantage, other than unifying the page tracking structures,
this offers is that we replace the vmalloc'ed array (which can be up to
a megabyte in size) with a chain of individual pages which helps reduce
memory pressure.

The disadvantage is that we then do not have a simple array to iterate,
or to access randomly. The common case for this is in the relocation
processing, which will typically fit within a single scatterlist page
and so be almost the same cost as the simple array. For iterating over
the array, the extra function call could be optimised away, but in
reality is an insignificant cost of either binding the pages, or
performing the pwrite/pread.

v2: Fix drm_clflush_sg() to not invoke wbinvd as well! And fix the
trivial compile error from rebasing.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

By using the recently introduced pinning of pages, we can safely drop
the mutex in the knowledge that the pages are not going to disappear
beneath us, and so we can simplify the code for iterating over the pages.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NBen Widawsky <ben@bwidawsk.net>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

By using the recently introduced pinning of pages, we can safely drop
the mutex in the knowledge that the pages are not going to disappear
jeneath us, and so we can simplify the code for iterating over the pages.

Note: The old code had such complicated page refcounting since it used
obj->pages as a micro-optimization if it's there, but that could
(before this patch) disappear when we drop the dev->struct_mutex.
Hence some manual page refcounting was required for the slow path,
complicated by the fact that pages returned by shmem_read_mapping_page
already have a pageref, which needs to be dropped again.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NBen Widawsky <ben@bwidawsk.net>
[danvet: Added note to explain the question Ben raised in review.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We need to refcount our pages in order to prevent reaping them at
inopportune times, such as when they currently vmapped or exported to
another driver. However, we also wish to keep the lazy deallocation of
our pages so we need to take a pin/unpinned approach rather than a
simple refcount.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NBen Widawsky <ben@bwidawsk.net>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

In order to specialise functions depending upon the type of object, we
can attach vfuncs to each object via a new ->ops pointer.

For instance, this will be used in future patches to only bind pages from
a dma-buf for the duration that the object is used by the GPU - and so
prevent them from pinning those pages for the entire of the object.

v2: Bonus comments.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NBen Widawsky <ben@bwidawsk.net>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We hit this a lot with i915 and although we'd like to engineer things to hit
it a lot less, this commit at least makes it consume a few less cycles.

from something containing
movzwl 0x0(%rip),%r10d
to
add    %r8,%rdx

I only noticed it while using perf to profile something else.
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDave Airlie <airlied@redhat.com>

The SH Mobile LCD controller (LCDC) DRM driver supports the main
graphics plane in RGB and YUV formats, as well as the overlay planes (in
alpha-blending mode only).

Only flat panel outputs using the parallel interface are supported.
Support for SYS panels, HDMI and DSI is currently not implemented.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: NSascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>

This patchset introduces a set of helper function for implementing the KMS
framebuffer layer for drivers which use the DRM GEM CMA helper function.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Tested-by: NSascha Hauer <s.hauer@pengutronix.de>
Acked-by: NSascha Hauer <s.hauer@pengutronix.de>
[Make DRM_KMS_CMA_HELPER a boolean Kconfig option]
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>

Many embedded drm devices do not have a IOMMU and no dedicated
memory for graphics. These devices use CMA (Contiguous Memory
Allocator) backed graphics memory. This patch provides helper
functions to be able to share the code. The code technically does
not depend on CMA as the backend allocator, the name has been chosen
because CMA makes for a nice, short but still descriptive function
prefix.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
Tested-by: NLars-Peter Clausen <lars@metafoo.de>
[Make DRM_GEM_CMA_HELPER a boolean Kconfig option]
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>

This goes back to

commit c1c7af60
Author: Jesse Barnes <jbarnes@virtuousgeek.org>
Date:   Thu Sep 10 15:28:03 2009 -0700

    drm/i915: force mode set at lid open time

It was used to fix an issue on a i915GM based Thinkpad X41, which
somehow clobbered the modeset state at lid close time. Since then
massive amounts of things changed: Tons of fixes to the modeset
sequence, OpRegion support, better integration with the acpi code.
Especially OpRegion /should/ allow us to control the display hw
cooperatively with the firmware, without the firmware clobbering the
hw state behind our backs.

So it's dubious whether we still need this.

The second issue is that it's unclear who's responsibility it actually
is to restore the mode - Chris Wilson suggests to just emit a hotplug
event and let userspace figure things out.

The real reason I've stumbled over this is that the new modeset code
breaks drm_helper_resume_force_mode - it OOPSes derefing a NULL vfunc
pointer. The reason this wasn't caught in testing earlier is that in

commit c9354c85
Author: Linus Torvalds <torvalds@linux-foundation.org>
Date:   Mon Nov 2 09:29:55 2009 -0800

    i915: fix intel graphics suspend breakage due to resume/lid event
    confusion

logic was added to _not_ restore the modeset state after a resume. And
since most machines are configured to auto-suspend on lid-close, this
neatly papered over the issue.

Summarizing, this shouldn't be required on any platform supporting
OpRegion. And none of the really old machines I have here seem to
require it either. Hence I'm inclined to just rip it out.

But in case that there are really firmwares out there that clobber the
hw state, replace it with a call to intel_modset_check_state. This
will ensure that we catch any issues as soon as they happen.

Cc: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

While reworking the modeset sequence, this got lost in

commit 25c5b266
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date:   Sun Jul 8 22:08:04 2012 +0200

    drm/i915: implement new set_mode code flow

I've noticed this because some Xorg versions seem to set up a new mode
with every crtc at (0,0) and then pan to the right multi-monitor
setup. And since some hacks of mine added more calls to mode_set using
the stored crtc->x/y my multi-screen setup blew up.
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Limit printing bad edid information at one time per connector.
Connector that are connected to a bad monitor/kvm will likely
stay connected to the same bad monitor/kvm and it makes no
sense to keep printing the bad edid message.
Signed-off-by: NJerome Glisse <jglisse@redhat.com>
Reviewed-by: NAdam Jackson <ajax@redhat.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

This patch removes a unused struct psb_intel_connector

Sparse gives a warning:
drivers/gpu/drm/gma500/cdv_intel_hdmi.c:142:30: warning:
	unused variable ‘psb_intel_connector’ [-Wunused-variable]
Signed-off-by: NEmil Goode <emilgoode@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

The memory return by kzalloc() or kmem_cache_zalloc() has already
be set to zero, so remove useless memset(0).
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: NDave Airlie <airlied@redhat.com>

The current logic for probing ddc is limited to
2 blocks (256 bytes), this patch adds support
for the 4 block (512) data.

To do this, a single 8-bit segment index is
passed to the display via the I2C address 30h.
Data from the selected segment is then immediately
read via the regular DDC2 address using a repeated
I2C 'START' signal.
Signed-off-by: NShirish S <s.shirish@samsung.com>
Reviewed-by: NJean Delvare <jdelvare@suse.de>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: NVille Syrjala <ville.syrjala@linux.intel.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Since arch/arm/include/asm/pgtable.h contains:

#define io_remap_pfn_range(vma,from,pfn,size,prot) \
                remap_pfn_range(vma, from, pfn, size, prot)

there is no point treating ARM as a special case in distinguishing
between remap_pfn_range() and io_remap_pfn_range().
Signed-off-by: NRobert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

There are two slightly different pieces of code for HDMI VSDB
detection. Unify the code into a single helper function.

Also fix a bug where drm_detect_hdmi_monitor() would stop looking
for the HDMI VSDB after the first vendor specific block is found,
whether or not that block happened to be the HDMI VSDB. The
standard allows for any number of vendor specific blocks to be
present.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NAdam Jackson <ajax@redhat.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

The length of HDMI VSDB must be at least 5 bytes. Other than the minimum,
nothing else about the length is specified. Check the length before
accessing any additional field beyond the minimum length.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NAdam Jackson <ajax@redhat.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Make sure drm_detect_hdmi_monitor() and drm_detect_monitor_audio() don't
access beyond the extension block.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NAdam Jackson <ajax@redhat.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>