Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The size of the eeprom data is 1088 bytes for AR9485. But
a sanity check is done against 4K which would result in a
'potential read past the end of the buffer' smatch complaint.
Reported-by: NDan Carpenter <error27@gmail.com>
Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Introduce a helper function to get the EEPROM mode from channel and remove
multiple similar switch statements. Also since it's now easy to get the EEPROM
mode from the channel, use them inside the functions which need it, instead of
passing a redundant ee_mode parameter.
Signed-off-by: NBruno Randolf <br1@einfach.org>
Acked-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Remove redundant defines.
Signed-off-by: NBruno Randolf <br1@einfach.org>
Acked-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add a new variable to keep track of the currently configured tx power. Before
max_pwr was re-used for keeping the maximum allowed power as well as the
current configuration. Doing a min() on it allows you to lower the txpower, but
how would you be able to make it higher again?

This patch fixes that by adding a new variable ah_cur_pwr which is used instead
of txp_max_pwr to keep the current configuration. txp_max_pwr is used to check
if we are within the limits.

Another problem fixed by this patch is that it avoids setting a zero txpower
when things are initialized first and the current power is not yet set.
Signed-off-by: NBruno Randolf <br1@einfach.org>
Acked-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

And rename functions which write the powertable to make it clearer.
Signed-off-by: NBruno Randolf <br1@einfach.org>
Acked-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Let ath5k_hw_txpower() decide if it can re-use the powertable or if it has to
be recalculated instead of passing a 'fast' flag from the outside.
Signed-off-by: NBruno Randolf <br1@einfach.org>
Acked-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There is a missing unlock when we hit the "No beacon slot available"
error condition.
Signed-off-by: NDan Carpenter <error27@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Use function pci_pcie_cap() instead of accessing struct member directly.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Tested-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Use function pci_is_pcie() instead of accessing struct member directly.

CC: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Use function pci_is_pcie() instead of accessing struct member directly.

CC: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Use function pci_is_pcie() instead of accessing struct member directly.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Acked-by: NGertjan van Wingerde <gwingerde@gmail.com>
Acked-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Use function pci_is_pcie() instead of accessing struct member directly.

CC: Michael Buesch <mb@bu3sch.de>
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

No function declared in gpio.h is used here.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Acked-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

No function declared in gpio.h is used here.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Acked-by: NKalle Valo <kvalo@adurom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

ath9k supports its own set of virtual wiphys, and it uses
the mac80211 idle notifications to know when a device needs
to be idle or not. We recently changed ath9k to force idle
on driver stop() and on resume but forgot to take into account
ath9k's own virtual wiphy idle states. These are used internally
by ath9k to check if the device's radio should be powered down
on each idle call. Without this change its possible that the
device could have been forced off but the virtual wiphy idle
was left on.

Cc: stable@kernel.org
Cc: Paul Stewart <pstew@google.com>
Cc: Amod Bodas <amod.bodas@atheros.com>
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The recently added warning message on power change failure
is not needed on device removal.

ath: Failed to wakeup in 500us
------------[ cut here ]------------
WARNING: at drivers/net/wireless/ath/ath9k/hw.c:1618
ath9k_hw_setpower+0x61f/0x630 [ath9k_hw]()
Hardware name: 64756D6
Pid: 540, comm: kworker/u:3 Not tainted 2.6.37-rc6-wl #37
Call Trace:
 [<ffffffff810501aa>] warn_slowpath_common+0x7a/0xb0
 [<ffffffffa056e280>] ? ath9k_iowrite32+0x0/0x90 [ath9k]
 [<ffffffff810501f5>] warn_slowpath_null+0x15/0x20
 [<ffffffffa05226ef>] ath9k_hw_setpower+0x61f/0x630 [ath9k_hw]
 [<ffffffffa05700e5>] ath9k_ps_wakeup+0x85/0xd0 [ath9k]
 [<ffffffffa0570685>] ath9k_configure_filter+0x25/0x80 [ath9k]
 [<ffffffffa04dde43>] ieee80211_configure_filter+0x133/0x190 [mac80211]
 [<ffffffffa04ee502>] ieee80211_do_stop+0x132/0x540 [mac80211]
 [<ffffffff813466ff>] ? _raw_spin_unlock_bh+0x1f/0x30
 [<ffffffff812b6923>] ? dev_deactivate+0x1c3/0x1e0
 [<ffffffffa04ee925>] ieee80211_stop+0x15/0x20 [mac80211]
 [<ffffffff8129d1b6>] __dev_close+0x56/0x90
Signed-off-by: NRajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The commit "ath9k_hw: warn if we cannot change the power to the chip"
introduced a new warning to indicate chip powerup failures, but this
is not required for devices that have been removed. Handle USB device
removal properly by checking for unplugged status.

For PCI devices, this warning will still be seen when the card is pulled
out, not sure how to check for card removal.
Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

These drivers share one header file, but nothing else.  Worse, both
drivers use the rtl8225 part with different register settings.  The
results has been some ugly naming -- let's simplify that.
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
Acked-by: NHin-Tak Leung <htl10@users.sourceforge.net>
Acked-by: NLarry Finger <Larry.Finger@lwfinger.net>
Acked-by: NHerton Ronaldo Krzesinski <herton@mandriva.com.br>

create_workqueue is deprecated.  The workqueue usage does not seem to
demand any special treatment, so do not set any flags either.
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
Tested-by: NLarry Finger <Larry.Finger@lwfinger.net>
Acked-by: NTejun Heo <tj@kernel.org>

Restricting the chainmask to 1 for legacy mode disables useful features
such as MRC, and it reduces the available transmit power.
I can't think of a good reason to do this in legacy mode, so let's just
get rid of that code.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The commit 'ath9k_hw: Disable PAPRD for rates with low Tx power' changed
the code that sets the PAPRD rate masks to use only either the HT20 mask
or the HT40 mask. This is wrong, as the hardware can still use HT20 rates
even when configured for HT40, and the operating channel mode does not
affect PAPRD operation.
The register for the HT40 rate mask is applied as a mask on top of the
other registers to selectively disable PAPRD for specific rates on HT40
packets only.
This patch changes the code back to the old behavior which matches the
intended use of these registers. While with current cards this should not
make any practical difference (according to Atheros, the HT20 and HT40
mask should always be equal), it is more correct that way, and maybe
the HT40 mask will be used for some rare corner cases in the future.

Cc: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When an skb is shared, it needs to be duplicated, along with its data buffer.
If the skb does not have enough headroom, using skb_copy might cause the data
buffer to be copied twice (once by skb_copy and once by pskb_expand_head).
Fix this by using skb_clone initially and letting ieee80211_skb_resize sort
out the rest.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

If the skb is not cloned and we don't need any extra headroom, there
is no point in reallocating the skb head.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The change 'mac80211: Fix BUG in pskb_expand_head when transmitting shared skbs'
added a check for copying the skb if it's shared, however the tx info variable
still points at the cb of the old skb
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Acked-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

wl12xx_get_platform_data() returns an ERR_PTR on failure and it never
returns a NULL.
Signed-off-by: NDan Carpenter <error27@gmail.com>
Acked-by: NKalle Valo <kvalo@adurom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

A previous conversion from semaphoreto mutexes missed the fact that one
of the semaphores was used in interrupt code. Fixed by changing to
a spinlock.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

ath9k channel table for 2Ghz does not seems to initialize the 'band'
parameter.Though it does not seems to cause any visible issue it looks
odd when we initialize the 'band' parameter for 5Ghz channel table while
not so for 2Ghz.
Signed-off-by: NMohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NAnisse Astier <anisse@astier.eu>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When rfkill is enabled, ath9k_hw unnecessarily configured the baseband to
turn off based on GPIO input, however that code was hardcoded to GPIO 0
instead of ah->rfkill_gpio.
Since ath9k uses software rfkill anyway, this code is completely unnecessary
and should be removed in case anything else ever uses GPIO 0.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

To improve aggregation length, there should not be more than two fully formed
A-MPDU frames in the hardware queue. To ensure this, the code checks the tx
queue length before forming new A-MPDUs. This can reduce the throughput (or
maybe even starve out A-MPDU traffic) when too many non-aggregated frames are
in the queue.
Fix this by keeping track of pending A-MPDU frames (even when they're sent out
as single frames), but exclude rate control probing frames to improve
performance.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
Tested-by: NLarry Finger <Larry.Finger@lwfinger.net>

The Mesh Control header only includes 0, 1 or 2 addresses. If there is
one address, it should be interpreted as Address 4.  If there are 2,
they are interpreted as Addresses 5 and 6 (Address 4 being the 4th
address in the 802.11 header).

The address extension used to hold up to 3 addresses instead of the current 2.
I'm not sure which draft version changed this, but it is very unlikely that it
will change again given the state of the approval process of this draft.  See
section 7.1.3.6.3 in current draft (8.0).

Also, note that the extra address that I'm removing was not being used, so this
change has no effect on over-the-air frame formats.  But I thought I better
remove it before someone does start using it.
Signed-off-by: NJavier Cardona <javier@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>