提交 f1a8abb0 编写于 作者: F Felix Fietkau 提交者: John W. Linville

ath9k_hw: fix PA predistortion HT40 mask

The commit 'ath9k_hw: Disable PAPRD for rates with low Tx power' changed
the code that sets the PAPRD rate masks to use only either the HT20 mask
or the HT40 mask. This is wrong, as the hardware can still use HT20 rates
even when configured for HT40, and the operating channel mode does not
affect PAPRD operation.
The register for the HT40 rate mask is applied as a mask on top of the
other registers to selectively disable PAPRD for specific rates on HT40
packets only.
This patch changes the code back to the old behavior which matches the
intended use of these registers. While with current cards this should not
make any practical difference (according to Atheros, the HT20 and HT40
mask should always be equal), it is more correct that way, and maybe
the HT40 mask will be used for some rare corner cases in the future.

Cc: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
上级 f8a0a781
......@@ -4762,6 +4762,7 @@ static void ath9k_hw_ar9300_set_txpower(struct ath_hw *ah,
struct ath_regulatory *regulatory = ath9k_hw_regulatory(ah);
struct ath_common *common = ath9k_hw_common(ah);
struct ar9300_eeprom *eep = &ah->eeprom.ar9300_eep;
struct ar9300_modal_eep_header *modal_hdr;
u8 targetPowerValT2[ar9300RateSize];
u8 target_power_val_t2_eep[ar9300RateSize];
unsigned int i = 0, paprd_scale_factor = 0;
......@@ -4771,15 +4772,17 @@ static void ath9k_hw_ar9300_set_txpower(struct ath_hw *ah,
if (ah->eep_ops->get_eeprom(ah, EEP_PAPRD)) {
if (IS_CHAN_2GHZ(chan))
ah->paprd_ratemask = (IS_CHAN_HT40(chan) ?
le32_to_cpu(eep->modalHeader2G.papdRateMaskHt40) :
le32_to_cpu(eep->modalHeader2G.papdRateMaskHt20))
& AR9300_PAPRD_RATE_MASK;
modal_hdr = &eep->modalHeader2G;
else
ah->paprd_ratemask = (IS_CHAN_HT40(chan) ?
le32_to_cpu(eep->modalHeader5G.papdRateMaskHt40) :
le32_to_cpu(eep->modalHeader5G.papdRateMaskHt20))
& AR9300_PAPRD_RATE_MASK;
modal_hdr = &eep->modalHeader5G;
ah->paprd_ratemask =
le32_to_cpu(modal_hdr->papdRateMaskHt20) &
AR9300_PAPRD_RATE_MASK;
ah->paprd_ratemask_ht40 =
le32_to_cpu(modal_hdr->papdRateMaskHt40) &
AR9300_PAPRD_RATE_MASK;
paprd_scale_factor = ar9003_get_paprd_scale_factor(ah, chan);
min_pwridx = IS_CHAN_HT40(chan) ? ALL_TARGET_HT40_0_8_16 :
......
......@@ -134,7 +134,7 @@ static int ar9003_paprd_setup_single_table(struct ath_hw *ah)
REG_RMW_FIELD(ah, AR_PHY_PAPRD_AM2PM, AR_PHY_PAPRD_AM2PM_MASK,
ah->paprd_ratemask);
REG_RMW_FIELD(ah, AR_PHY_PAPRD_HT40, AR_PHY_PAPRD_HT40_MASK,
AR_PHY_PAPRD_HT40_MASK);
ah->paprd_ratemask_ht40);
for (i = 0; i < ah->caps.max_txchains; i++) {
REG_RMW_FIELD(ah, ctrl0[i],
......
......@@ -835,6 +835,7 @@ struct ath_hw {
unsigned int paprd_target_power;
unsigned int paprd_training_power;
unsigned int paprd_ratemask;
unsigned int paprd_ratemask_ht40;
bool paprd_table_write_done;
u32 paprd_gain_table_entries[PAPRD_GAIN_TABLE_ENTRIES];
u8 paprd_gain_table_index[PAPRD_GAIN_TABLE_ENTRIES];
......
Markdown is supported
0% .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑!
想要评论请 注册