Removes omap-hdmi DAI driver, omap-hdmi-card driver, the related
Kconfig options, and Makefile entries. The HDMI DAI drivers has been
integrated directly to OMAP4+ HDMI drivers and simple-card driver is
used instead of omap-hdmi-card driver.
Signed-off-by: NJyri Sarha <jsarha@ti.com>
Acked-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: NMark Brown <broonie@kernel.org>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Implements callbacks for OMAP HDMI audio platform driver and registers
it in probe function. Unregistering is done in remove function.
Signed-off-by: NJyri Sarha <jsarha@ti.com>
Reviewed-by: NMark Brown <broonie@kernel.org>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Removes the OMAP5 HDMI audio callbacks for the old external DAI driver.
Signed-off-by: NJyri Sarha <jsarha@ti.com>
Reviewed-by: NMark Brown <broonie@kernel.org>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Implements callbacks for OMAP HDMI audio platform driver and registers
it in probe function. Unregistering is done in remove function.
Signed-off-by: NJyri Sarha <jsarha@ti.com>
Reviewed-by: NMark Brown <broonie@kernel.org>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Removes the OMAP4 HDMI audio callbacks for the old external DAI driver.
Signed-off-by: NJyri Sarha <jsarha@ti.com>
Reviewed-by: NMark Brown <broonie@kernel.org>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Make hdmi_mode_has_audio() more user friedly by taking hdmi_config as
parameter.
Signed-off-by: NJyri Sarha <jsarha@ti.com>
Reviewed-by: NMark Brown <broonie@kernel.org>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

The booleans are not used anymore. Just select SND_OMAP_SOC_HDMI_AUDIO
to enable OMAP HDMI audio support.
Signed-off-by: NJyri Sarha <jsarha@ti.com>
Reviewed-by: NMark Brown <broonie@kernel.org>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

The platform device should only be registered from OMAPDSS HDMI
driver. The platform driver registers and unregisters all ASoC
components needed for OMAP HDMI audio.

The hdmi audio driver implements cpu-dai component using the callbacks
provided by OMAPDSS and registers the component under DSS HDMI
device. Omap-pcm is registered for platform component also under DSS
HDMI device. Dummy codec is used as as codec component. The hdmi audio
driver implements also the card and registers it under its own
platform device.
Signed-off-by: NJyri Sarha <jsarha@ti.com>
Acked-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: NMark Brown <broonie@kernel.org>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Adds display_enabled flag and audio_abort_cb callback to struct hdmi.
Signed-off-by: NJyri Sarha <jsarha@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

This is used to store omap-hdmi-audio pdev for unregistering it.
Signed-off-by: NJyri Sarha <jsarha@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Unify the private anonymous struct in hdmi4.c and hdmi5.c, name it as
struct omap_hdmi, and make it public in hdmi.h.
Signed-off-by: NJyri Sarha <jsarha@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

The audio dma port is found in the hdmi_wp physical address space.
Signed-off-by: NJyri Sarha <jsarha@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

hdmi4_audio_get_dma_port() is unused and and broken.
Signed-off-by: NJyri Sarha <jsarha@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

It does not waste too many bytes to compile all audio related core
functions always in with HDMI support. It should help readability and
in keeping the audio code in working shape. Leave the options just for
disabling and enabling the functionality in hdmi[45].c.
Signed-off-by: NJyri Sarha <jsarha@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

The OMAP5 HDMI audio implementation needs HDMI_AUDIO_LAYOUT_6CH in
hdmi_core_audio_layout enum. I found the correct value from ti-linux
3.8 tree.
Signed-off-by: NJyri Sarha <jsarha@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

The hdmi_wp_audio_config_format() expects sample_order of struct
hdmi_audio_format to be initialized. The only allowed value is
HDMI_AUDIO_SAMPLE_LEFT_FIRST.
Signed-off-by: NJyri Sarha <jsarha@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Only OMAP4 DSS has non reserved bits above 6th bit in HDMI_WP_AUDIO_CFG.
Signed-off-by: NJyri Sarha <jsarha@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Now that the DSS has the common DSS PLL, we no longer use the DSI PLL
feature flags from dss_features.c.

Remove all the unused feature flags.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Now that we have the common DSS PLL support, change HDMI to use it. This
results in quite a lot of changes, but almost all of them are trivial
name changes.

The function to program the PLL settings can be removed from hdmi_pll.c,
as the common PLL API contains the same functionality.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

hdmi_pll_enable powers off the PLL as the first thing it does. Right
after that, it enables the PLL powers.

The initial power-off is pointless, so let's remove it.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

At the moment we have one function, hdmi_pll_enable, which enables the
PLL and writes the PLL configuration to registers.

To make the HDMI PLL ahere to the DSS PLL API, split the hdmi_pll_enable
into two parts: hdmi_pll_enable which enables the PLL HW, and
hdmi_pll_set_config which writes the config.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

HDMI PLL code needs the pointer to the WP block so that it can manage
its power. Currently this is passed as a function parameter to
hdmi_pll_enable and hdmi_pll_disable. To make the PLL function adhere to
the DSS PLL API, we need to remove the WP parameter.

This patch stores the WP pointer to hdmi_pll_data in hdmi_pll_init, so
that it's available when needed.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

The SYSRESET bits in HDMI PLL do not reset the PLL itself, but only
affect the power used for the PLL.

Afaik there is no reason to use the SYSRESET bits, and we don't use it
in the other PLLs, so let's remove the HDMI PLL reset to make the PLL
code simpler and similar to other PLLs.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

The code calculating HDMI PLL parameters has always been very confusing.
Now that we are implementing a common PLL library for the DSS, it's
important that the PLL code is understandable.

This patch rewrites the calculation code, and removes a few hacks that
were used there.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

We don't support interlace modes properly on OMAP5+ HDMI, so we need to
reject interlace timings.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Only OMAP5+ has REFSEL field, but at the moment it's set also on OMAP4.

Fix this by adding a "has_refsel" field, and setting the REFSEL based on
that.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Now that we have the common DSS PLL support, change DSI to use it. This
results in quite a lot of changes, but almost all of them are trivial
name changes.

The functions to calculate and program the PLL settings can be removed
from dsi.c, as the common PLL API contains the same functionality.

We also need to create struct dss_pll_hw entries for PLL hardware
features for different OMAP platforms, instead of using the
dss_features.c as the old code does.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

OMAP DSS currently contains two different PLLs: DSI PLL (Type A PLL) and
HDMI PLL (Type B PLL). When DRA7 support is added, we will also support
Video PLLs (Type A).

The driver currently handles all PLLs totally separately. This patch
adds common DSS PLL code, which

a) lets us have common code for the PLLs
b) lets the users of the PLLs use a common API, instead of DSI API or
   HDMI API.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

When DPI uses the DSI PLL for pixel clock, the DPI code will call
dsi_runtime_get/put to keep the DSI block enabled. A much simpler way to
handle this is to do dsi_runtime_get/put in DSI's dsi_pll_init() and
dsi_pll_uninit(), thus removing the need for DSI to call the runtime PM
functions.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

The HSDIV outputs of DSI PLL (and also other PLLs) all have the same
bit width for the divider value.

Simplify the code by merging HSDIV divider widths into one width.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

We are creating a common DSS PLL code, so having fixed DSI specific
hsdiv fields in the clock information is not ok.

This patch changes the hsdiv fields to arrays, so that we can use all
the 4 possible hsdiv outputs (DSI only usees 2), and we have generic way
to access the hsdivs.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

We are creating a common DSS PLL code, so rename 'clkin4ddr' field,
which is DSI specific name, to 'clkdco' which is a generic name.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Now that dsi_clock_info only contains information about the PLL, we can
just copy the whole struct when storing the clock information, instead
of copying individual fields.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

We have pll_locked field in struct dsi_data, but it doesn't have any
meaningful use anymore, and can be removed.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

struct dsi_clock_info contains clkin field, which is the rate of the
PLL's input clock. This field is not needed, as it can be easily
retrieved by using the clk_get_rate().

This patch removes the clkin field.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

struct dsi_clock_info represents the clocks handled by the DSI, mostly
PLL related clocks. In an effort to create common PLL code, we need to
remove all the non-PLL items from dsi_clock_info.

This patch removes LP clock related fields from dsi_clock_info, and
creates a new struct dsi_lp_clock_info for holding clock info for the LP
clock.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

The DSS PLL has support to power on the PLL's highspeed clock output
and HSDIV output separately. In practice both need to powered on, as in
most OMAP's that's the only working configuration. We already do that in
dsi_pll_init(), by overriding the passed arguments so that both are
always powered.

Simplify the code by removing the support for choosing which outputs to
power on.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

With the previous patch "OMAPDSS: DSI: wait for hsdiv clocks when
enabling PLL",  dsi_wait_pll_hsdiv_dispc_active and
dsi_wait_pll_hsdiv_dsi_active are no longer needed, so they and the
callers can be removed.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

At the moment we have two functions to wait for the HSDIV clocks to get
active, dsi_wait_pll_hsdiv_dispc_active and
dsi_wait_pll_hsdiv_dsi_active. Instead of such inconvenient functions,
let's just make sure that the hsdiv clocks are active after the pll has
been enabled.

This patch adds code to dsi_pll_set_clock_div() to wait until HSDIV
clocks are active.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Add a 'port' parameter in dpi_select_source. The param tells the port
number of the DPI instance that we want to configure. We use this number
to select the overlay manager for that DPI instance.
Signed-off-by: NArchit Taneja <archit@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>