It was previously disabled pending a bugfix, which has since been
resolved.
Signed-off-by: NSteven Toth <stoth@hauppauge.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Don't display the register when it's not appropriate for the specific port.
Signed-off-by: NSteven Toth <stoth@hauppauge.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Certain DVB cards that have demodulators on TS1/VIDB were not streaming packets.
This ensure the pin directions on PAD_CTRL are set correctly, solving the issue.
Signed-off-by: NSteven Toth <stoth@hauppauge.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

PAD_CTRL controls TS1 and TS2 input and output states, if the register
became corrupt the driver was never able to recover.
Signed-off-by: NSteven Toth <stoth@hauppauge.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

With the HVR1800, trying to use video0 and video1 simultaneously caused
buffer corruption in the PCIe bridge. This fix reallocates video1
buffer locations to avoid the issue.
Signed-off-by: NSteven Toth <stoth@hauppauge.com>
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

cx18: Lock the aux PLL to the video pixel rate for analog captures.  The
datasheet for the CX25840 says this is important for MPEG encoding applications.
To ensure the PLL locking was correct, also fixed the aux PLL's multiplier to
be computed based on a precise crystal freq of 4.5 MHz/286 * 455/2 * 8 =
28636363.6363... instead of the imporperly rounded 28636363.
Signed-off-by: NAndy Walls <awalls@radix.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

cx18: Fix 32 kHz audio sample output rate for analog tuner SIF input so it
works.  The AUX_PLL VCO was being operated at 196.6 MHz out of the spec'ed
200-600 MHz range.  Fixed the multipler and post dividers to operate the VCO
within specification and added comments on how magic numbers are derived.

Thanks to Hans Verkuil for pointing out this interesting problem to solve.
Signed-off-by: NAndy Walls <awalls@radix.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

gspca_sonixb remove one more no longer needed special case from the code
Signed-off-by: NHans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

gspca_sonixb remove some no longer needed sn9c103+ov7630 special cases
Signed-off-by: NAndoni Zubimendi <andoni.zubimendi@gmail.com>
Signed-off-by: NHans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

gspca_sonixb remove non working ovXXXX contrast, hue and saturation ctrls
Signed-off-by: NHans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Andoni Zubimendi has been doing some testing with his sn9c103 cam with
ov7630 sensor, and with this patch the exposure setting and autoexposure now
work.

This patch also removes some special cases in the shared ov6650 / ov7630 code
which now are handled the same for both sensors and it adds a new special case
which stops us from changing the hsync / vsync polarity settings from their
default on the ov7630 (which we were doing as a side-effect of using the ov6650
exposure code for the ov7630).

Last this patch removes the superficial difference between the OV7630 and
OV7630_3 sensors.
Signed-off-by: NAndoni Zubimendi <andoni.zubimendi@gmail.com>
Signed-off-by: NHans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

This patch contains the following cleanups:
- mark smscore_module_init() as __init
- mark smscore_module_exit as __exit
- make the following needlessly global code static:
  - smscoreapi.c: struct g_smscore_notifyees
  - smscoreapi.c: struct g_smscore_devices
  - smscoreapi.c: struct g_smscore_deviceslock
  - smscoreapi.c: struct g_smscore_registry
  - smscoreapi.c: struct g_smscore_registrylock
  - smscoreapi.c: smscore_module_init()
  - smscoreapi.c: smscore_module_exit()
  - smsdvb.c: struct g_smsdvb_clients
  - smsdvb.c: struct g_smsdvb_clientslock
Signed-off-by: NAdrian Bunk <bunk@kernel.org>
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Fix a bug introduced by some trouble on my -git tree that resulted on a hunk to
be lost (probably caused by some rebase).
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

* 'x86/auditsc' of git://git.kernel.org/pub/scm/linux/kernel/git/frob/linux-2.6-roland:
  i386 syscall audit fast-path
  x86_64 ia32 syscall audit fast-path
  x86_64 syscall audit fast-path
  x86_64: remove bogus optimization in sysret_signal

* 'sched/for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  sched: hrtick_enabled() should use cpu_active()
  sched, x86: clean up hrtick implementation
  sched: fix build error, provide partition_sched_domains() unconditionally
  sched: fix warning in inc_rt_tasks() to not declare variable 'rq' if it's not needed
  cpu hotplug: Make cpu_active_map synchronization dependency clear
  cpu hotplug, sched: Introduce cpu_active_map and redo sched domain managment (take 2)
  sched: rework of "prioritize non-migratable tasks over migratable ones"
  sched: reduce stack size in isolated_cpu_setup()
  Revert parts of "ftrace: do not trace scheduler functions"

Fixed up conflicts in include/asm-x86/thread_info.h (due to the
TIF_SINGLESTEP unification vs TIF_HRTICK_RESCHED removal) and
kernel/sched_fair.c (due to cpu_active_map vs for_each_cpu_mask_nr()
introduction).

Merge branch 'cpus4096-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'cpus4096-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (31 commits)
  NR_CPUS: Replace NR_CPUS in speedstep-centrino.c
  cpumask: Provide a generic set of CPUMASK_ALLOC macros, FIXUP
  NR_CPUS: Replace NR_CPUS in cpufreq userspace routines
  NR_CPUS: Replace per_cpu(..., smp_processor_id()) with __get_cpu_var
  NR_CPUS: Replace NR_CPUS in arch/x86/kernel/genapic_flat_64.c
  NR_CPUS: Replace NR_CPUS in arch/x86/kernel/genx2apic_uv_x.c
  NR_CPUS: Replace NR_CPUS in arch/x86/kernel/cpu/proc.c
  NR_CPUS: Replace NR_CPUS in arch/x86/kernel/cpu/mcheck/mce_64.c
  cpumask: Optimize cpumask_of_cpu in lib/smp_processor_id.c, fix
  cpumask: Use optimized CPUMASK_ALLOC macros in the centrino_target
  cpumask: Provide a generic set of CPUMASK_ALLOC macros
  cpumask: Optimize cpumask_of_cpu in lib/smp_processor_id.c
  cpumask: Optimize cpumask_of_cpu in kernel/time/tick-common.c
  cpumask: Optimize cpumask_of_cpu in drivers/misc/sgi-xp/xpc_main.c
  cpumask: Optimize cpumask_of_cpu in arch/x86/kernel/ldt.c
  cpumask: Optimize cpumask_of_cpu in arch/x86/kernel/io_apic_64.c
  cpumask: Replace cpumask_of_cpu with cpumask_of_cpu_ptr
  Revert "cpumask: introduce new APIs"
  cpumask: make for_each_cpu_mask a bit smaller
  net: Pass reference to cpumask variable in net/sunrpc/svc.c
  ...

Fix up trivial conflicts in drivers/cpufreq/cpufreq.c manually

Merge branch 'core/softlockup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'core/softlockup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  softlockup: fix invalid proc_handler for softlockup_panic
  softlockup: fix watchdog task wakeup frequency
  softlockup: fix watchdog task wakeup frequency
  softlockup: show irqtrace
  softlockup: print a module list on being stuck
  softlockup: fix NMI hangs due to lock race - 2.6.26-rc regression
  softlockup: fix false positives on nohz if CPU is 100% idle for more than 60 seconds
  softlockup: fix softlockup_thresh fix
  softlockup: fix softlockup_thresh unaligned access and disable detection at runtime
  softlockup: allow panic on lockup

* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (85 commits)
  [ARM] pxa: add base support for PXA930 Handheld Platform (aka SAAR)
  [ARM] pxa: add base support for PXA930 Evaluation Board (aka TavorEVB)
  [ARM] pxa: add base support for PXA930 (aka Tavor-P)
  [ARM] Update mach-types
  [ARM] pxa: make littleton to use the new smc91x platform data
  [ARM] pxa: make zylonite to use the new smc91x platform data
  [ARM] pxa: make mainstone to use the new smc91x platform data
  [ARM] pxa: make lubbock to use new smc91x platform data
  [NET] smc91x: prepare SMC_USE_PXA_DMA to be specified in platform data
  [NET] smc91x: prepare for SMC_IO_SHIFT to be a platform configurable variable
  [NET] smc91x: add SMC91X_NOWAIT flag to platform data
  [NET] smc91x: favor the use of SMC91X_USE_* instead of SMC_CAN_USE_*
  [NET] smc91x: remove "irq_flags" from "struct smc91x_platdata"
  [ARM] 5146/1: pxa2xx: convert all boards to call pxa2xx_transceiver_mode helper
  Support for LCD on e740 e750 e400 and e800 e-series PDAs
  E-series UDC support
  PXA UDC - allow use of inverted GPIO for pullup
  Add e350 support
  Fix broken e-series build
  E-series GPIO / IRQ definitions.
  ...

This adds fast paths for 32-bit syscall entry and exit when
TIF_SYSCALL_AUDIT is set, but no other kind of syscall tracing.
These paths does not need to save and restore all registers as
the general case of tracing does.  Avoiding the iret return path
when syscall audit is enabled helps performance a lot.
Signed-off-by: NRoland McGrath <roland@redhat.com>

This adds fast paths for 32-bit syscall entry and exit when
TIF_SYSCALL_AUDIT is set, but no other kind of syscall tracing.
These paths does not need to save and restore all registers as
the general case of tracing does.  Avoiding the iret return path
when syscall audit is enabled helps performance a lot.
Signed-off-by: NRoland McGrath <roland@redhat.com>

This adds a fast path for 64-bit syscall entry and exit when
TIF_SYSCALL_AUDIT is set, but no other kind of syscall tracing.
This path does not need to save and restore all registers as
the general case of tracing does.  Avoiding the iret return path
when syscall audit is enabled helps performance a lot.
Signed-off-by: NRoland McGrath <roland@redhat.com>

This short-circuit path in sysret_signal looks wrong to me.
AFAICT, in practice the branch is never taken--and if it were,
it would go wrong.  To wit, try loading a module whose init
function does set_thread_flag(TIF_IRET), and see insmod crash
(presumably with a wrong user stack pointer).

This is because the FIXUP_TOP_OF_STACK work hasn't been done yet
when we jump around the call to ptregscall_common and get to
int_with_check--where it expects the user RSP,SS,CS and EFLAGS to
have been stored by FIXUP_TOP_OF_STACK.

I don't think it's normally possible to get to sysret_signal with no
_TIF_DO_NOTIFY_MASK bits set anyway, so these two instructions are
already superfluous.  If it ever did happen, it is harmless to call
do_notify_resume with nothing for it to do.
Signed-off-by: NRoland McGrath <roland@redhat.com>

Signed-off-by: NJean-Francois Moine <moinejf@free.fr>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NJean-Francois Moine <moinejf@free.fr>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NAdrian Bunk <bunk@kernel.org>
Signed-off-by: NJean-Francois Moine <moinejf@free.fr>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NJean-Francois Moine <moinejf@free.fr>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

The version numbers of the subrivers will be removed as these ones
will be changed for any other purpose.
Signed-off-by: NJean-Francois Moine <moinejf@free.fr>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NJean-Francois Moine <moinejf@free.fr>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

The functions in a header should not belong to another module. The prio functions
belong to v4l2-common.c, so move them to v4l2-common.h.

The ioctl functions belong to v4l2-ioctl.c, so create a new v4l2-ioctl.h header
and move those functions to it.
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

As reported by Hans Verkuil:

In file included from /home/v4l/master/v4l/dw2102.c:14:
/home/v4l/master/v4l/z0194a.h:93: error: 'STV0229_LOCKOUTPUT_1' undeclared here (not in a function)

This is due to some typos that were fixed on stv0299.

This patch renames it in accord with that fix.
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

The class_dev field is a normal device, not a class device. This is very
confusing and now that the old 'dev' field has been renamed to 'parent'
we can rename 'class_dev' to just 'dev'.
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

The field 'dev' is not the video device, but the parent of the video device.
Rename accordingly.
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

videodev.c became top-heavy so all the ioctl processing has been split off
into v4l2-ioctl.c. This means videodev.c is back to its original purpose:
creating and registering v4l devices.

Since videodev.c and v4l2-ioctl.c should still remain one module (as least
for now) I also had to rename videodev.c to v4l2-dev.c to prevent a
circular dependency when building a videodev.ko module. This is not a bad
thing, since the source and header now have the same name. And the v4l2-
prefix is useful to see which sources are generic v4l2 support code.
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc:
  sdhci: highmem capable PIO routines
  sg: reimplement sg mapping iterator
  mmc_test: print message when attaching to card
  mmc: Remove Russell as primecell mci maintainer
  mmc_block: bounce buffer highmem support
  sdhci: fix bad warning from commit c8b3e02e
  sdhci: add warnings for bad buffers in ADMA path
  mmc_test: test oversized sg lists
  mmc_test: highmem tests
  s3cmci: ensure host stopped on machine shutdown
  au1xmmc: suspend/resume implementation
  s3cmci: fixes for section mismatch warnings
  pxamci: trivial fix of DMA alignment register bit clearing

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx: (24 commits)
  I/OAT: I/OAT version 3.0 support
  I/OAT: tcp_dma_copybreak default value dependent on I/OAT version
  I/OAT: Add watchdog/reset functionality to ioatdma
  iop_adma: cleanup iop_chan_xor_slot_count
  iop_adma: document how to calculate the minimum descriptor pool size
  iop_adma: directly reclaim descriptors on allocation failure
  async_tx: make async_tx_test_ack a boolean routine
  async_tx: remove depend_tx from async_tx_sync_epilog
  async_tx: export async_tx_quiesce
  async_tx: fix handling of the "out of descriptor" condition in async_xor
  async_tx: ensure the xor destination buffer remains dma-mapped
  async_tx: list_for_each_entry_rcu() cleanup
  dmaengine: Driver for the Synopsys DesignWare DMA controller
  dmaengine: Add slave DMA interface
  dmaengine: add DMA_COMPL_SKIP_{SRC,DEST}_UNMAP flags to control dma unmap
  dmaengine: Add dma_client parameter to device_alloc_chan_resources
  dmatest: Simple DMA memcpy test client
  dmaengine: DMA engine driver for Marvell XOR engine
  iop-adma: fix platform driver hotplug/coldplug
  dmaengine: track the number of clients using a channel
  ...

Fixed up conflict in drivers/dca/dca-sysfs.c manually

* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jwessel/linux-2.6-kgdb:
  kgdb: kgdboc console poll hooks for mpsc uart
  kgdb: kgdboc console poll hooks for cpm uart
  kgdb, powerpc: arch specific powerpc kgdb support
  kgdb: support for ARCH=arm
  kgdb: remove unused HAVE_ARCH_KGDB_SHADOW_INFO config variable

* git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6: (60 commits)
  ide: small whitespace fixes
  ide: ide-cd_ioctl.c fix sparse integer as NULL pointer warnings
  ide: ide-cd.c fix sparse endianness warnings
  ide-cd: convert to using the new atapi_flags
  ide: remove unused PC_FLAG_DRQ_INTERRUPT
  ide-scsi: convert to using the new atapi_flags
  ide-tape: convert to using the new atapi_flags
  ide-floppy: convert to using the new atapi_flags (take 2)
  ide: add per-device flags
  ide: use rq->cmd instead of pc->c in atapi common code
  ide-scsi: pass packet command in rq->cmd
  ide-tape: pass packet command in rq->cmd
  ide-tape: make room for packet command ids in rq->cmd
  ide-floppy: pass packet command in rq->cmd
  ide: remove pc->callback member from ide_atapi_pc
  ide-scsi: use drive->pc_callback instead of pc->callback
  ide-tape: use drive->pc_callback instead of pc->callback
  ide-floppy: use drive->pc_callback instead of pc->callback
  ide: push pc callback pointer into the ide_drive_t structure
  drivers/ide/ide-tape.c: remove double kfree
  ...