dw-mmc controller can support multiple slots.
But, there are no use-cases anywhere. So we don't need to support the
slot-node for dw-mmc controller.
And "supports-highspeed" property in dw-mmc is deprecated.
"supports-highspeed" property can be replaced with "cap-sd/mmc-highspeed".
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: NTushar Behera <trblinux@gmail.com>
Reviewed-by: NUlf Hansson <ulf.hansson@linaro.org>
Tested-by: NSachin Kamat <sachin.kamat@samsung.com>
[kgene.kim@samsung.com: rebased exynos5250-snow changes]
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

The IRQB interrupt pin of MAX77686 PMIC is connected to GPX3[2] pin of
Exynos5250 on the Exynos5250 SMDK board. Specify this connection using
interrupts property for the max77686 pmic node.
Signed-off-by: NThomas Abraham <thomas.ab@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

This patch replaces the "cs-gpio" from "controller-data" node
as was specified in the old binding and uses the standard
"cs-gpios" property expected by the SPI core as is defined now
in the spi-s3c64xx driver DT binding.
Signed-off-by: NNaveen Krishna Chatradhi <ch.naveen@samsung.com>
Reviewed-by: NJavier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: NTomasz Figa <t.figa@samsung.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Add generic compatible strings to the respective board DT files.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

This patch adds dt entry for ahci sata controller and its
corresponding phy controller.phy node has been added w.r.t
new generic phy framework.
Signed-off-by: NYuvaraj Kumar C D <yuvaraj.cd@samsung.com>
Acked-by: NKishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Now that the SPI controllers are disabled by default for Exynos5250
there is no need to explicitly disable them in individual board files.
This hunk appears not to have been merged when doing the original
conversion, add it now.
Signed-off-by: NMark Brown <broonie@linaro.org>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Some boards might not have RTC xtal, so RTC shouldn't really be
enabled by default. Enable it in the required board files. For
now enable it for all board files to maintain the enabled status
exisitng prior to this patch.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Add Maxim 77686 PMIC node for EXYNOS5250 based SMDK5250 board.
Signed-off-by: NThomas Abraham <thomas.ab@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Ensure that unused I2C controllers are not activated, causing problems due
to inappropriate pinmuxing or similar, by marking the controllers as
disabled by default and requiring boards to explicitly enable those that
are in use.
Signed-off-by: NMark Brown <broonie@linaro.org>
Acked-by: NTomasz Figa <t.figa@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Rather than requiring each board to explicitly disable the SPI controllers
it is not using instead require boards to enable those that they are using.
This is less work overall since normally at most one of the controllers is
in use and avoids issues caused by inappropriate pinmuxing.
Signed-off-by: NMark Brown <broonie@linaro.org>
Acked-by: NTomasz Figa <t.figa@samsung.com>
Reviewed-by: NDoug Anderson <dianders@chromium.org>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

There is a 16.934MHz fixed rate clock connected to MCLK1 on the CODEC, add
this to the device tree bindings.
Signed-off-by: NMark Brown <broonie@linaro.org>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

For consistency with other device tree nodes, this patch adds missing
spaces after node labels.
Signed-off-by: NTomasz Figa <t.figa@samsung.com>
Acked-by: NKyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

This patch rename's the device tree mmc node's from "dwmmc" to "mmc".
According to ePAPR chapter 2.2.2 generic node name recommendation,
it has been opted change from dwmmc to mmc.Also this patch remove the
instance index from the node name.
Signed-off-by: NYuvaraj Kumar C D <yuvaraj.cd@samsung.com>
Reviewed-by: NTomasz Figa <t.figa@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

As fifo-depth property in dw_mmc device tree node is SOC
specific, move this property to exynos5250 SOC specific
file.
Signed-off-by: NYuvaraj Kumar C D <yuvaraj.cd@samsung.com>
Reviewed-by: NTomasz Figa <t.figa@samsung.com>
[kgene.kim@samsung.com: squashed fifo-depth patch for cros5250-common]
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

According to ePAPR, chapter 2.3.4, the status property has
defined that it should be set to "disabled" when "the device
is not presently operational, but it might become operational
in the future".

So this patch disable dwmmc node by "status = disabled" in SOC
dts file and enable dwmmc node by "status = okay" in board specific
dts file.
Signed-off-by: NYuvaraj Kumar C D <yuvaraj.cd@samsung.com>
Reviewed-by: NTomasz Figa <t.figa@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Rather than requiring each board to explicitly disable the I2S controllers
it is not using instead require boards to enable those that they are using.

This is required for audio operation on Arndale, one of the unused I2S
controllers is pinmuxed with the LDO enable GPIOs for the WM1811A.
Signed-off-by: NMark Brown <broonie@linaro.org>
Acked-by: NMark Rutland <mark.rutland@arm.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Moves the properties of DP controller to exynos5.dtsi which are common
across exynos5 SoCs like Exynos5250 and Exynos5420.

The PHY DP Node is based on Jingoo Han's <jg1.han@samsung.com> patch
at https://patchwork.linuxtv.org/patch/19189/Signed-off-by: NVikas Sajjan <vikas.sajjan@linaro.org>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

As the display-timing information is parsed by FIMD driver, it makes
sense to move the display-timing DT node inside FIMD DT node for exynos5250
Signed-off-by: NVikas Sajjan <vikas.sajjan@linaro.org>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

This patch renames the combatible strings for hdmi, mixer, ddc
and hdmiphy. It follows the convention of using compatible string
which represent the SoC in which the IP was added for the first
time.
Signed-off-by: NRahul Sharma <rahul.sharma@samsung.com>
Acked-by: NKukjin Kim <kgene.kim@samsung.com>
Reviewed-by: NTomasz Figa <t.figa@samsung.com>
Signed-off-by: NInki Dae <inki.dae@samsung.com>

Replace /include/ (dtc) with #include (C pre-processor) for all
Samsung DT files
Signed-off-by: NPadmavathi Venna <padma.v@samsung.com>
Reviewed-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: NDoug Anderson <dianders@chromium.org>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

This patch adds the required regulator supplies and properties
for wm8994 codec on smdk5250 board.
Signed-off-by: NPadmavathi Venna <padma.v@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Add pin state information for DP HPD support that requires
pin configuration support using pinctrl interface.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Reviewed-by: NDoug Anderson <dianders@chromium.org>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

The 'samsung,vbus-gpio' was submitted before pinmux landed for
exynos5250 and uses the old-style gpio specifier.  Fix the two
exynos5250 boards that use it.
Signed-off-by: NDoug Anderson <dianders@chromium.org>
Signed-off-by: NOlof Johansson <olof@lixom.net>

Add display timing node to exynos5250-smdk5250.dts
Signed-off-by: NLeela Krishna Amudala <l.krishna@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Add default pin state information for all client nodes that require
pin configuration support using pinctrl interface.
Signed-off-by: NThomas Abraham <thomas.abraham@linaro.org>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Tested-by: NDoug Anderson <dianders@chromium.org>
Reviewed-by: NDoug Anderson <dianders@chromium.org>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

The clock frequency of xxti and xusbxti clocks is dependent on the
frequency of the on-board oscillator that is used to generate these
clocks. So allow the frequency of these clocks to be specfied from
device tree.
Signed-off-by: NThomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Adding EHCI device tree node for Exynos5250 along with
the device base adress and gpio line for vbus.
Signed-off-by: NVivek Gautam <gautam.vivek@samsung.com>
Acked-by: NJingoo Han <jg1.han@samsung.com>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Add device tree node for DP controller in EXYNOS5250 and
enable the instance for the SMDK5250 board.
Signed-off-by: NAjay Kumar <ajaykumar.rs@samsung.com>
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

The next change will remove the code from the dw_mmc-exynos that added
the DW_MCI_QUIRK_NO_WRITE_PROTECT.  Keep existing functionality of
having no write protect pin on smdk5250 by adding the disable-wp
property.
Signed-off-by: NDoug Anderson <dianders@chromium.org>
Acked-by: NSeungwon Jeon <tgih.jun@samsung.com>
Acked-by: NOlof Johansson <olof@lixom.net>
Signed-off-by: NChris Ball <cjb@laptop.org>

Add the basic device tree based lookup.
Signed-off-by: NPadmavathi Venna <padma.v@samsung.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Add device nodes for the three instances of i2s controllers in Exynos5
platforms. Enable instance i2s 0 for exynos5250 board and disable all
other i2s instances.
Signed-off-by: NPadmavathi Venna <padma.v@samsung.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

As per the current exynos-dw-mshc bindings, dw-mshc-sdr-timing and
dw-mshc-ddr-timing properties are having only two cells, these properties
are wrongly set for exynos5250 based cros5250 and smdk5250 platfroms. This
patch corrects above timing propreties for above platfroms
Signed-off-by: NAlim Akhtar <alim.akhtar@samsung.com>
Tested-by: NDoug Anderson <dianders@chromium.org>
Acked-by: NDoug Anderson <dianders@chromium.org>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

The aliases for dwmmc were placed in the SMDK5250 dts file but really
should be common for all exynos5250 boards.  Move it to the common CPU
file.
Signed-off-by: NDoug Anderson <dianders@chromium.org>
Acked-by: NOlof Johansson <olof@lixom.net>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

This patch adds Device Nodes for SATA and SATA PHY device.
Signed-off-by: NVasanth Ananthan <vasanth.a@samsung.com>
[kgene.kim@samsung.com: removed address definitions as per comments]
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

This patch adds support for device tree based discovery for exynos5
hdmi ddc.
Signed-off-by: NRahul Sharma <rahul.sharma@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

This patch adds support for device tree based discovery for exynos5
hdmiphy.
Signed-off-by: NRahul Sharma <rahul.sharma@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

This patch adds support for device tree based discovery for exynos5
hdmi. Hdmi node is also renamed with "exynos5-hdmi".
Signed-off-by: NRahul Sharma <rahul.sharma@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

This patch adds device tree entry for MFC v6 in the Exynos5
SoC. Makes the required changes in the clock files and adds
MFC to the DT device list.
Signed-off-by: NNaveen Krishna Chatradhi <ch.naveen@samsung.com>
Signed-off-by: NArun Kumar K <arun.kk@samsung.com>
[kgene.kim@samsung.com: fixed section mismatches Seung-Woo Kim reported]
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Add device nodes for the four instances of dw_mmc controllers in
EXYNOS5250 and enable instance 0 and 2 for the SMDK5250 board.
Signed-off-by: NThomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Cc: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>