- 25 3月, 2010 3 次提交
-
-
由 Juuso Oikarinen 提交于
Add support for the set_cqm_config op. This op function configures the requested connection quality monitor rssi threshold and rssi hysteresis values to the hardware if the hardware supports IEEE80211_HW_SUPPORTS_CQM. For unsupported hardware, currently -EOPNOTSUPP is returned, so the mac80211 is currently not doing connection quality monitoring on the host. This could be added later, if needed. Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com> Reviewed-by: NJohannes Berg <johannes@sipsolutions.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Juuso Oikarinen 提交于
Add support for basic configuration of a connection quality monitoring to the nl80211 interface, and basic support for notifying about triggered monitoring events. Via this interface a user-space connection manager may configure and receive pre-warning events of deteriorating WLAN connection quality, and start preparing for roaming in advance, before the connection is already lost. An example usage of such a trigger is starting scanning for nearby AP's in an attempt to find one with better connection quality, and associate to it before the connection characteristics of the existing connection become too bad or the association is even lost, leading in a prolonged delay in connectivity. The interface currently supports only RSSI, but it could be later extended to include other parameters, such as signal-to-noise ratio, if need for that arises. Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com> Reviewed-by: NJohannes Berg <johannes@sipsolutions.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Amitkumar Karwar 提交于
Auto auth mode is enabled by default. If user doesn't specify the auth mode, while association driver will first try with open mode and then with shared key mode. If user specifies an auth mode, auto auth is disabled and driver will not try association with another auth mode. Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com> Signed-off-by: NBing Zhao <bzhao@marvell.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 24 3月, 2010 37 次提交
-
-
由 Sujith 提交于
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Daniel Ngu 提交于
WARNING: braces {} are not necessary for any arm of this statement Signed-off-by: NDaniel Ngu <daniel.dy.ngu@gmail.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Juuso Oikarinen 提交于
This patch is based on a RFC patch by Kalle Valo. The wl1271 has a feature which handles the connection monitor logic in hardware, basically sending periodically nullfunc frames and reporting to the host if AP is lost, after attempting to recover by sending probe-requests to the AP. Add support to mac80211 by adding a new flag IEEE80211_HW_CONNECTION_MONITOR which prevents conn_mon_timer from triggering during idle periods, and prevents sending probe-requests to the AP if beacon-loss is indicated by the hardware. Cc: Kalle Valo <kalle.valo@nokia.com> Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com> Reviewed-by: NJohannes Berg <johannes@sipsolutions.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Joe Perches 提交于
Change local functions that are cast to iw_handler to the more standard use with "union iwreq_data *wrqu" so the iw_handler array no longer needs the casts. Signed-off-by: NJoe Perches <joe@perches.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Joe Perches 提交于
Use IW_HANDLER from wireless.h instead Signed-off-by: NJoe Perches <joe@perches.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Joe Perches 提交于
Use #define IW_HANDLER from wireless.h instead Signed-off-by: NJoe Perches <joe@perches.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Joe Perches 提交于
Convert direct uses of [ (foo - SIOCIWFIRST) , fn) Signed-off-by: NJoe Perches <joe@perches.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Joe Perches 提交于
There's a wireless.h macro for this, might as well use it. Signed-off-by: NJoe Perches <joe@perches.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Joe Perches 提交于
There's a wireless.h macro for this, might as well use it. Signed-off-by: NJoe Perches <joe@perches.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Joe Perches 提交于
These two #defines use the same value, but SIOCIWFIRST makes more sense in this use. Signed-off-by: NJoe Perches <joe@perches.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Joe Perches 提交于
Copied the idea from orinoco Signed-off-by: NJoe Perches <joe@perches.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Teemu Paasikivi 提交于
Changed platform_device to be allocated dynamically from the wl1271_alloc_hw function. Also cleaned up error handling in the wl1271_alloc_hw function and module probe functions. Signed-off-by: NTeemu Paasikivi <ext-teemu.3.paasikivi@nokia.com> Reviewed-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com> Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com> Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Juuso Oikarinen 提交于
Removing the wl1271 from the inet addr notifier chain sometimes causes the registered handler to be called - causing locking problems if the removing function is called from within the mutex. Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com> Reviewed-by: NTeemu Paasikivi <ext-teemu.3.paasikivi@nokia.com> Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Juuso Oikarinen 提交于
The null func template is not needed for ad-hoc, and it's generation is not supported for ad-hoc (mac80211 will WARN about it.) Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com> Reviewed-by: NTeemu Paasikivi <ext-teemu.3.paasikivi@nokia.com> Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Juuso Oikarinen 提交于
This patch adds support for the filters configured by the mac80211 stack. Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com> Reviewed-by: NTeemu Paasikivi <ext-teemu.3.paasikivi@nokia.com> Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Teemu Paasikivi 提交于
Removed duplicate code from wl1271_sdio module remove function. For freeing stuff in the remove function wl1271_free_hw function is now used. Signed-off-by: NTeemu Paasikivi <ext-teemu.3.paasikivi@nokia.com> Reviewed-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com> Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com> Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Teemu Paasikivi 提交于
Added separate flag for SDIO debugging. Previously it has used DEBUG_SPI flag. This patch also includes couple indentation fixes. Signed-off-by: NTeemu Paasikivi <ext-teemu.3.paasikivi@nokia.com> Reviewed-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com> Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com> Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Juuso Oikarinen 提交于
It's no longer needed. Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com> Reviewed-by: NKalle Valo <kalle.valo@nokia.com> Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Juuso Oikarinen 提交于
This patch fixes MAC address handling. To achieve this, firmware booting had to be delayed from the previous op_start to op_add_interface, which is the point when the driver gets to know the configured MAC address. As the wl1271 only supports one virtual interface, this even seems quite logical. Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com> Reviewed-by: NKalle Valo <kalle.valo@nokia.com> Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Kalle Valo 提交于
wl1271 supports U-APSD similarly as wl1251, so let's enable it. Signed-off-by: NKalle Valo <kalle.valo@nokia.com> Reviewed-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com> Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com> Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Kalle Valo 提交于
Commit "wl1271: implement WMM" accidentally used CONF_PS_SCHEME_LEGACY_PSPOLL, but instead CONF_PS_SCHEME_LEGACY should be used as earlier. Signed-off-by: NKalle Valo <kalle.valo@nokia.com> Reviewed-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com> Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com> Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Kalle Valo 提交于
Needed for U-APSD. Signed-off-by: NKalle Valo <kalle.valo@nokia.com> Reviewed-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com> Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com> Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Kalle Valo 提交于
If we get probe request from mac80211, we can remove two functions. Signed-off-by: NKalle Valo <kalle.valo@nokia.com> Reviewed-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com> Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com> Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Kalle Valo 提交于
mac80211 now can create pspoll and nullfunc templates, better to use those. Signed-off-by: NKalle Valo <kalle.valo@nokia.com> Reviewed-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com> Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com> Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Kalle Valo 提交于
Everything is ready now and we can enable WMM in wl1271. Signed-off-by: NKalle Valo <kalle.valo@nokia.com> Reviewed-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com> Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com> Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Juuso Oikarinen 提交于
Add a sysfs file to control the state of the BT co-ex (enable or disable it.) By default, the BT co-ex is enabled. Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com> Reviewed-by: NTeemu Paasikivi <ext-teemu.3.paasikivi@nokia.com> Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Juuso Oikarinen 提交于
In order to get the platform device for both SPI and SDIO, move the platform device registration to wl1271_main.c from wl1271_spi.c. Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com> Reviewed-by: NTeemu Paasikivi <ext-teemu.3.paasikivi@nokia.com> Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Juuso Oikarinen 提交于
Add configuration values for the varous WLAN-BT co-ex configuration parameters, and finally enable WLAN-BT co-ex. Based on preliminary measurements, it appears the co-ex feature is not increasing WLAN power consumption, if BT is not activated. Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com> Reviewed-by: NTeemu Paasikivi <ext-teemu.3.paasikivi@nokia.com> Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Juuso Oikarinen 提交于
The bluetooth coexistence (SG) configuration messages have changed and were completely wrong. For instance, intending to enable the SG, it was instead disabled. Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com> Reviewed-by: NTeemu Paasikivi <ext-teemu.3.paasikivi@nokia.com> Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Teemu Paasikivi 提交于
Changed driver to keep MMC host claimed while wlan interface is up. This keeps MMC stack from powering the SDIO device down. Signed-off-by: NTeemu Paasikivi <ext-teemu.3.paasikivi@nokia.com> Reviewed-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com> Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com> Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Teemu Paasikivi 提交于
Added method for wlan power control to io_ops struct and moved wl1271_power_on and wl1271_power_off functions to wl1271_io.h. Signed-off-by: NTeemu Paasikivi <ext-teemu.3.paasikivi@nokia.com> Reviewed-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com> Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com> Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Juuso Oikarinen 提交于
The per-queue TX opportunity value is configured by the mac80211 in units of 32us. The firmware however wants it in us, so add the conversion. Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com> Reviewed-by: NKalle Valo <kalle.valo@nokia.com> Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Sujith 提交于
Features: * Station mode * IBSS mode * Monitor mode * Legacy support * HT support * TX/RX 11n Aggregation * HW encryption * LED * Suspend/Resume For more information: http://wireless.kernel.org/en/users/Drivers/ath9k_htcSigned-off-by: NSujith <Sujith.Manoharan@atheros.com> Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com> Signed-off-by: NSenthil Balasubramanian <senthilkumar@atheros.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Sujith 提交于
Without this you will get a panic if the device initialization fails. Also, free ath_hw instance properly. ath9k_hw_deinit() shouldn't do it. Cc: stable@kernel.org Signed-off-by: NSujith <Sujith.Manoharan@atheros.com> Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Sujith 提交于
AR9271 needs a full reset only upon the first reset, add a call for the driver to enable these special resets. We can optimize this out later without an export. Signed-off-by: NSujith <Sujith.Manoharan@atheros.com> Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com> Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Sujith 提交于
When initializing the PLL on AR9271 we always need to set the core clock to 117MHz. While at it remove the baud rate settings for the serial device on the AR9271, the default settings work well unless you want to customize it. Signed-off-by: NSujith <Sujith.Manoharan@atheros.com> Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com> Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Sujith 提交于
Periodic power amplifier offset calibration is skipped on ath9k algorithmically, this is required on AR9271. Signed-off-by: NSujith <Sujith.Manoharan@atheros.com> Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com> Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-