- 29 4月, 2016 26 次提交
-
-
由 David Rivshin 提交于
The phy-handle, phy_id, and fixed-link properties are mutually exclusive, and only one need be specified. Make this clear in the binding doc. Also mark the phy_id property as deprecated, as phy-handle should be used instead. Signed-off-by: NDavid Rivshin <drivshin@allworx.com> Reviewed-by: NMugunthan V N <mugunthanvnm@ti.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 David Rivshin 提交于
The phy-mode emac property was only being processed in the phy_id or fixed-link cases. However if phy-handle was specified instead, an error message would complain about the lack of phy_id or fixed-link, and then jump past the of_get_phy_mode(). This would result in the PHY mode defaulting to MII, regardless of what the devicetree specified. Fixes: 9e42f715 ("drivers: net: cpsw: add phy-handle parsing") Signed-off-by: NDavid Rivshin <drivshin@allworx.com> Tested-by: NNicolas Chauvet <kwizart@gmail.com> Tested-by: NAndrew Goodbody <andrew.goodbody@cambrionix.com> Reviewed-by: NMugunthan V N <mugunthanvnm@ti.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 David Rivshin 提交于
If an emac node has a phy-handle property that points to something which is not a phy, then a segmentation fault will occur when the interface is brought up. This is because while phy_connect() will return ERR_PTR() on failure, of_phy_connect() will return NULL. The common error check uses IS_ERR(), and so missed when of_phy_connect() fails. The NULL pointer is then dereferenced. Also, the common error message referenced slave->data->phy_id, which would be empty in the case of phy-handle. Instead, use the name of the device_node as a useful identifier. And in the phy_id case add the error code for completeness. Fixes: 9e42f715 ("drivers: net: cpsw: add phy-handle parsing") Signed-off-by: NDavid Rivshin <drivshin@allworx.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 David Rivshin 提交于
Commit 9e42f715 ("drivers: net: cpsw: add phy-handle parsing") saved the "phy-handle" phandle into a new cpsw_priv field. However, phy connections are per-slave, so the phy_node field should be in cpsw_slave_data rather than cpsw_priv. This would go unnoticed in a single emac configuration. But in dual_emac mode, the last "phy-handle" property parsed for either slave would be used by both of them, causing them both to refer to the same phy_device. Fixes: 9e42f715 ("drivers: net: cpsw: add phy-handle parsing") Signed-off-by: NDavid Rivshin <drivshin@allworx.com> Tested-by: NNicolas Chauvet <kwizart@gmail.com> Tested-by: NAndrew Goodbody <andrew.goodbody@cambrionix.com> Reviewed-by: NMugunthan V N <mugunthanvnm@ti.com> Reviewed-by: NGrygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Andreas Larsson 提交于
Signed-off-by: NAndreas Larsson <andreas@gaisler.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Jiri Benc 提交于
The collect metadata mode does not support GUE nor FOU. This might be implemented later; until then, we should reject such config. I think this is okay to be changed. It's unlikely anyone has such configuration (as it doesn't work anyway) and we may need a way to distinguish whether it's supported or not by the kernel later. For backwards compatibility with iproute2, it's not possible to just check the attribute presence (iproute2 always includes the attribute), the actual value has to be checked, too. Fixes: 2e15ea39 ("ip_gre: Add support to collect tunnel metadata.") Signed-off-by: NJiri Benc <jbenc@redhat.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 David S. Miller 提交于
Petko Manolov says: ==================== pegasus: correct buffer & packet sizes As noticed by Lincoln Ramsay <a1291762@gmail.com> some old (usb 1.1) Pegasus based devices may actually return more bytes than the specified in the datasheet amount. That would not be a problem if the allocated space for the SKB was equal to the parameter passed to usb_fill_bulk_urb(). Some poor bugger (i really hope it was not me, but 'git blame' is useless in this case, so anyway) decided to add '+ 8' to the buffer length parameter. Sometimes the usb transfer overflows and corrupts the socket structure, leading to kernel panic. The above doesn't seem to happen for newer (Pegasus2 based) devices which did help this bug to hide for so long. The new default is to not include the CRC at the end of each received package. So far CRC has been ignored which makes no sense to do it in a first place. The patch is against v4.6-rc5 and was tested on ADM8515 device by transferring multiple gigabytes of data over a couple of days without any complaints from the kernel. Please apply it to whatever net tree you deem fit. Changes since v1: - split the patch in two parts; - corrected the subject lines; Changes since v2: - do not append CRC by default (based on a discussion with Johannes Berg); ==================== Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Petko Manolov 提交于
The default Pegasus setup was to append the status and CRC at the end of each received packet. The status bits are used to update various stats, but CRC has been ignored. The new default is to not append CRC at the end of RX packets. Signed-off-by: NPetko Manolov <petkan@mip-labs.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Petko Manolov 提交于
usb_fill_bulk_urb() receives buffer length parameter 8 bytes larger than what's allocated by alloc_skb(); This seems to be a problem with older (pegasus usb-1.1) devices, which may silently return more data than the maximal packet length. Reported-by: NLincoln Ramsay <a1291762@gmail.com> Signed-off-by: NPetko Manolov <petkan@mip-labs.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 David S. Miller 提交于
Jiri Benc says: ==================== gre: fix lwtunnel support This patchset fixes a few bugs in ipgre metadata mode implementation. As an example, in this setup: ip a a 192.168.1.1/24 dev eth0 ip l a gre1 type gre external ip l s gre1 up ip a a 192.168.99.1/24 dev gre1 ip r a 192.168.99.2/32 encap ip dst 192.168.1.2 ttl 10 dev gre1 ping 192.168.99.2 the traffic does not go through before this patchset and does as expected with it applied. v3: Back to v1 in order not to break existing users. Dropped patch 3, will be fixed in iproute2 instead. v2: Rejecting invalid configuration, added patch 3, dropped patch for ETH_P_TEB (will target net-next). ==================== Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Jiri Benc 提交于
In ipgre (i.e. not gretap) + collect metadata mode, the skb was assumed to contain Ethernet header and was encapsulated as ETH_P_TEB. This is not the case, the interface is ARPHRD_IPGRE and the protocol to be used for encapsulation is skb->protocol. Fixes: 2e15ea39 ("ip_gre: Add support to collect tunnel metadata.") Signed-off-by: NJiri Benc <jbenc@redhat.com> Acked-by: NPravin B Shelar <pshelar@ovn.org> Reviewed-by: NSimon Horman <simon.horman@netronome.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Jiri Benc 提交于
In ipgre mode (i.e. not gretap) with collect metadata flag set, the tunnel is incorrectly assumed to be mGRE in NBMA mode (see commit 6a5f44d7). This is not the case, we're controlling the encapsulation addresses by lwtunnel metadata. And anyway, assigning dev->header_ops in collect metadata mode does not make sense. Although it would be more user firendly to reject requests that specify both the collect metadata flag and a remote/local IP address, this would break current users of gretap or introduce ugly code and differences in handling ipgre and gretap configuration. Keep the current behavior of remote/local IP address being ignored in such case. v3: Back to v1, added explanation paragraph. v2: Reject configuration specifying both remote/local address and collect metadata flag. Fixes: 2e15ea39 ("ip_gre: Add support to collect tunnel metadata.") Signed-off-by: NJiri Benc <jbenc@redhat.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 David S. Miller 提交于
Merge tag 'mac80211-for-davem-2016-04-27' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211 Johannes Berg says: ==================== Just a single fix, for a per-CPU memory leak in a (root user triggerable) error case. ==================== Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Timur Tabi 提交于
Commit 13a56b44 ("at803x: Add support for hardware reset") added a work-around for a hardware bug on the AT8030. However, the work-around was being called for all 803x PHYs, even those that don't need it. Function at803x_link_change_notify() checks to make sure that it only resets the PHY on the 8030, but it makes more sense to not call that function at all if it isn't needed. Signed-off-by: NTimur Tabi <timur@codeaurora.org> Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
git://git.open-mesh.org/linux-merge由 David S. Miller 提交于
Antonio Quartulli says: ==================== In this patchset you can find the following fixes: 1) check skb size to avoid reading beyond its border when delivering payloads, by Sven Eckelmann 2) initialize last_seen time in neigh_node object to prevent cleanup routine from accidentally purge it, by Marek Lindner 3) release "recently added" slave interfaces upon virtual/batman interface shutdown, by Sven Eckelmann 4) properly decrease router object reference counter upon routing table update, by Sven Eckelmann 5) release queue slots when purging OGM packets of deactivating slave interface, by Linus Lüssing Patch 2 and 3 have no "Fixes:" tag because the offending commits date back to when batman-adv was not yet officially in the net tree. ==================== Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Christophe Jaillet 提交于
The size allocated for target->hwinfo and the number of bytes copied in it should be consistent. Signed-off-by: NChristophe JAILLET <christophe.jaillet@wanadoo.fr> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Woojung Huh 提交于
At forced 100 Full & Half duplex mode, chip may fail to set mode correctly when cable is switched between long(~50+m) and short one. As workaround, set to 10 before setting to 100 at forced 100 F/H mode. Signed-off-by: NWoojung Huh <woojung.huh@microchip.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Woojung Huh 提交于
Fix rx_bytes, tx_bytes and tx_frames error in netdev.stats. - rx_bytes counted bytes excluding size of struct ethhdr. - tx_packets didn't count multiple packets in a single urb - tx_bytes included 8 bytes of extra commands. Signed-off-by: NWoojung Huh <woojung.huh@microchip.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Colin Ian King 提交于
The error return err is not initialized and there is a possibility that err is not assigned causing mv88e6xxx_port_bridge_join to return a garbage error return status. Fix this by initializing err to 0. Signed-off-by: NColin Ian King <colin.king@canonical.com> Reviewed-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Marcelo Ricardo Leitner 提交于
Fix casting in net_gso_ok. Otherwise the shift on gso_type << NETIF_F_GSO_SHIFT may hit the 32th bit and make it look like a INT_MIN, which is then promoted from signed to uint64 which is 0xffffffff80000000, resulting in wrong behavior when it is and'ed with the feature itself, as in: This test app: #include <stdio.h> #include <stdint.h> int main(int argc, char **argv) { uint64_t feature1; uint64_t feature2; int gso_type = 1 << 15; feature1 = gso_type << 16; feature2 = (uint64_t)gso_type << 16; printf("%lx %lx\n", feature1, feature2); return 0; } Gives: ffffffff80000000 80000000 So that this: return (features & feature) == feature; Actually works on more bits than expected and invalid ones. Fix is to promote it earlier. Issue noted while rebasing SCTP GSO patch but posting separetely as someone else may experience this meanwhile. Signed-off-by: NMarcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Neil Armstrong 提交于
When configured in fixed link, the DaVinci emac driver sets the priv->phydev to NULL and further ioctl calls to the phy_mii_ioctl() causes the kernel to crash. Cc: Brian Hutchinson <b.hutchman@gmail.com> Fixes: 1bb6aa56 ("net: davinci_emac: Add support for fixed-link PHY") Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com> Reviewed-by: NMugunthan V N <mugunthanvnm@ti.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 David S. Miller 提交于
Merge tag 'wireless-drivers-for-davem-2016-04-25' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers Kalle Valo says: ==================== wireless-drivers fixes for 4.6 ath9k * fix a couple release old throughput regression on ar9281 iwlwifi * add new device IDs for 8265 * fix a NULL pointer dereference when paging firmware asserts * remove a WARNING on gscan capabilities * fix MODULE_FIRMWARE for 8260 ==================== Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Bert Kenward 提交于
Add myself and Edward Cree as maintainers. Remove Shradha Shah, who is on extended leave. Cc: David S. Miller <davem@davemloft.net> Cc: Edward Cree <ecree@solarflare.com> Cc: Shradha Shah <sshah@solarflare.com> Signed-off-by: NBert Kenward <bkenward@solarflare.com> Acked-by: NEdward Cree <ecree@solarflare.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Jon Cooper 提交于
When certain firmware variants are selected (via the sfboot utility) the SFC7000 and SFC8000 series NICs don't support RSS. The driver still tries (and fails) to insert filters with the RSS flag, and the NIC fails to pass traffic. When the firmware reports RSS_LIMITED suppress allocating a default RSS context. The absence of an RSS context is picked up in filter insertion and RSS flags are discarded. Signed-off-by: NBert Kenward <bkenward@solarflare.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Stanislaw Gruszka 提交于
napi_disable() can not be called with bh disabled, move locking just around myri10ge_ss_lock_napi() . Patches fixes following bug: [ 114.278378] BUG: sleeping function called from invalid context at net/core/dev.c:4383 <snip> [ 114.313712] Call Trace: [ 114.314943] [<ffffffff817010ce>] dump_stack+0x19/0x1b [ 114.317673] [<ffffffff810ce7f3>] __might_sleep+0x173/0x230 [ 114.320566] [<ffffffff815b3117>] napi_disable+0x27/0x90 [ 114.323254] [<ffffffffa01e437f>] myri10ge_close+0xbf/0x3f0 [myri10ge] Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com> Acked-by: NHyong-Youb Kim <hykim@myri.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Eric Engestrom 提交于
Signed-off-by: NEric Engestrom <eric@engestrom.ch> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 28 4月, 2016 4 次提交
-
-
由 David S. Miller 提交于
Michael Chan says: ==================== bnxt_en: Bug fixes for net. Only use MSIX on VF, and fix rx page buffers on architectures with PAGE_SIZE >= 64K. ==================== Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michael Chan 提交于
If PAGE_SIZE is bigger than BNXT_RX_PAGE_SIZE, that means the native CPU page is bigger than the maximum length of the RX BD. Divide the page into multiple 32K buffers for the aggregation ring. Add an offset field in the bnxt_sw_rx_agg_bd struct to keep track of the page offset of each buffer. Since each page can be referenced by multiple buffer entries, call get_page() as needed to get the proper reference count. Signed-off-by: NMichael Chan <michael.chan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michael Chan 提交于
The RX BD length field of this device is 16-bit, so the largest buffer size is 65535. For LRO and GRO, we allocate native CPU pages for the aggregation ring buffers. It won't work if the native CPU page size is 64K or bigger. We fix this by defining BNXT_RX_PAGE_SIZE to be native CPU page size up to 32K. Replace PAGE_SIZE with BNXT_RX_PAGE_SIZE in all appropriate places related to the rx aggregation ring logic. The next patch will add additional logic to divide the page into 32K chunks for aggrgation ring buffers if PAGE_SIZE is bigger than BNXT_RX_PAGE_SIZE. Signed-off-by: NMichael Chan <michael.chan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michael Chan 提交于
Only MSI-X can be used on a VF. The driver should fail initialization if it cannot successfully enable MSI-X. Signed-off-by: NMichael Chan <michael.chan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 27 4月, 2016 5 次提交
-
-
由 Johannes Berg 提交于
In the case that dev_alloc_name() fails, e.g. because the name was given by the user and already exists, we need to clean up properly and free the per-CPU statistics. Fix that. Cc: stable@vger.kernel.org Fixes: 5a490510 ("mac80211: use per-CPU TX/RX statistics") Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
git://git.kernel.org/pub/scm/linux/kernel/git/davem/net由 Linus Torvalds 提交于
Pull networking fixes from David Miller: 1) Handle v4/v6 mixed sockets properly in soreuseport, from Craig Gallak. 2) Bug fixes for the new macsec facility (missing kmalloc NULL checks, missing locking around netdev list traversal, etc.) from Sabrina Dubroca. 3) Fix handling of host routes on ifdown in ipv6, from David Ahern. 4) Fix double-fdput in bpf verifier. From Jann Horn. * git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (31 commits) bpf: fix double-fdput in replace_map_fd_with_map_ptr() net: ipv6: Delete host routes on an ifdown Revert "ipv6: Revert optional address flusing on ifdown." net/mlx4_en: fix spurious timestamping callbacks net: dummy: remove note about being Y by default cxgbi: fix uninitialized flowi6 ipv6: Revert optional address flusing on ifdown. ipv4/fib: don't warn when primary address is missing if in_dev is dead net/mlx5: Add pci shutdown callback net/mlx5_core: Remove static from local variable net/mlx5e: Use vport MTU rather than physical port MTU net/mlx5e: Fix minimum MTU net/mlx5e: Device's mtu field is u16 and not int net/mlx5_core: Add ConnectX-5 to list of supported devices net/mlx5e: Fix MLX5E_100BASE_T define net/mlx5_core: Fix soft lockup in steering error flow qlcnic: Update version to 5.3.64 net: stmmac: socfpga: Remove re-registration of reset controller macsec: fix netlink attribute validation macsec: add missing macsec prefix in uapi ...
-
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc由 Linus Torvalds 提交于
Pull ARM SoC fixes from Arnd Bergmann: "Here are the latest bug fixes for ARM SoCs, mostly addressing recent regressions. Changes are across several platforms, so I'm listing every change separately here. Regressions since 4.5: - A correction of the psci firmware DT binding, to prevent users from relying on unintended semantics - Actually getting the newly merged clock driver for some OMAP platforms to work - A revert of patches for the Qualcomm BAM, these need to be reworked for 4.7 to avoid breaking boards other than the one they were intended for - A correction for the I2C device nodes on the Socionext Uniphier platform - i.MX SDHCI was broken for non-DT platforms due to a change with the setting of the DMA mask - A revert of a patch that accidentally added a nonexisting clock on the Rensas "Porter" board - A couple of OMAP fixes that are all related to suspend after the power domain changes for dra7 - On Mediatek, revert part of the power domain initialization changes that broke mt8173-evb Fixes for older bugs: - Workaround for an "external abort" in the omap34xx suspend/resume code. - The USB1/eSATA should not be listed as an excon device on am57xx-beagle-x15 (broken since v4.0) - A v4.5 regression in the TI AM33xx and AM43XX DT specifying incorrect DMA request lines for the GPMC - The jiffies calibration on Renesas platforms was incorrect for some modern CPU cores. - A hardware errata woraround for clockdomains on TI DRA7" * tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: drivers: firmware: psci: unify enable-method binding on ARM {64,32}-bit systems arm64: dts: uniphier: fix I2C nodes of PH1-LD20 ARM: shmobile: timer: Fix preset_lpj leading to too short delays Revert "ARM: dts: porter: Enable SCIF_CLK frequency and pins" ARM: dts: r8a7791: Don't disable referenced optional clocks Revert "ARM: OMAP: Catch callers of revision information prior to it being populated" ARM: OMAP3: Fix external abort on 36xx waking from off mode idle ARM: dts: am57xx-beagle-x15: remove extcon_usb1 ARM: dts: am437x: Fix GPMC dma properties ARM: dts: am33xx: Fix GPMC dma properties Revert "soc: mediatek: SCPSYS: Fix double enabling of regulators" ARM: mach-imx: sdhci-esdhc-imx: initialize DMA mask ARM: DRA7: clockdomain: Implement timer workaround for errata i874 ARM: OMAP: Catch callers of revision information prior to it being populated ARM: dts: dra7: Correct clock tree for sys_32k_ck ARM: OMAP: DRA7: Provide proper class to omap2_set_globals_tap ARM: OMAP: DRA7: wakeupgen: Skip SAR save for wakeupgen Revert "dts: msm8974: Add dma channels for blsp2_i2c1 node" Revert "dts: msm8974: Add blsp2_bam dma node" ARM: dts: Add clocks for dm814x ADPLL
-
由 Linus Torvalds 提交于
This is more prep-work for the upcoming pty changes. Still just code cleanup with no actual semantic changes. This removes a bunch pointless complexity by just having the slave pty side remember the dentry associated with the devpts slave rather than the inode. That allows us to remove all the "look up the dentry" code for when we want to remove it again. Together with moving the tty pointer from "inode->i_private" to "dentry->d_fsdata" and getting rid of pointless inode locking, this removes about 30 lines of code. Not only is the end result smaller, it's simpler and easier to understand. The old code, for example, depended on the d_find_alias() to not just find the dentry, but also to check that it is still hashed, which in turn validated the tty pointer in the inode. That is a _very_ roundabout way to say "invalidate the cached tty pointer when the dentry is removed". The new code just does dentry->d_fsdata = NULL; in devpts_pty_kill() instead, invalidating the tty pointer rather more directly and obviously. Don't do something complex and subtle when the obvious straightforward approach will do. The rest of the patch (ie apart from code deletion and the above tty pointer clearing) is just switching the calling convention to pass the dentry or file pointer around instead of the inode. Cc: Eric Biederman <ebiederm@xmission.com> Cc: Peter Anvin <hpa@zytor.com> Cc: Andy Lutomirski <luto@amacapital.net> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Peter Hurley <peter@hurleysoftware.com> Cc: Serge Hallyn <serge.hallyn@ubuntu.com> Cc: Willy Tarreau <w@1wt.eu> Cc: Aurelien Jarno <aurelien@aurel32.net> Cc: Alan Cox <gnomes@lxorguk.ukuu.org.uk> Cc: Jann Horn <jann@thejh.net> Cc: Greg KH <greg@kroah.com> Cc: Jiri Slaby <jslaby@suse.com> Cc: Florian Weimer <fw@deneb.enyo.de> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Jann Horn 提交于
When bpf(BPF_PROG_LOAD, ...) was invoked with a BPF program whose bytecode references a non-map file descriptor as a map file descriptor, the error handling code called fdput() twice instead of once (in __bpf_map_get() and in replace_map_fd_with_map_ptr()). If the file descriptor table of the current task is shared, this causes f_count to be decremented too much, allowing the struct file to be freed while it is still in use (use-after-free). This can be exploited to gain root privileges by an unprivileged user. This bug was introduced in commit 0246e64d ("bpf: handle pseudo BPF_LD_IMM64 insn"), but is only exploitable since commit 1be7f75d ("bpf: enable non-root eBPF programs") because previously, CAP_SYS_ADMIN was required to reach the vulnerable code. (posted publicly according to request by maintainer) Signed-off-by: NJann Horn <jannh@google.com> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org> Acked-by: NAlexei Starovoitov <ast@kernel.org> Acked-by: NDaniel Borkmann <daniel@iogearbox.net> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 26 4月, 2016 5 次提交
-
-
由 David Ahern 提交于
It was a simple idea -- save IPv6 configured addresses on a link down so that IPv6 behaves similar to IPv4. As always the devil is in the details and the IPv6 stack as too many behavioral differences from IPv4 making the simple idea more complicated than it needs to be. The current implementation for keeping IPv6 addresses can panic or spit out a warning in one of many paths: 1. IPv6 route gets an IPv4 route as its 'next' which causes a panic in rt6_fill_node while handling a route dump request. 2. rt->dst.obsolete is set to DST_OBSOLETE_DEAD hitting the WARN_ON in fib6_del 3. Panic in fib6_purge_rt because rt6i_ref count is not 1. The root cause of all these is references related to the host route for an address that is retained. So, this patch deletes the host route every time the ifdown loop runs. Since the host route is deleted and will be re-generated an up there is no longer a need for the l3mdev fix up. On the 'admin up' side move addrconf_permanent_addr into the NETDEV_UP event handling so that it runs only once versus on UP and CHANGE events. All of the current panics and warnings appear to be related to addresses on the loopback device, but given the catastrophic nature when a bug is triggered this patch takes the conservative approach and evicts all host routes rather than trying to determine when it can be re-used and when it can not. That can be a later optimizaton if desired. Signed-off-by: NDavid Ahern <dsa@cumulusnetworks.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 David S. Miller 提交于
This reverts commit 841645b5. Ok, this puts the feature back. I've decided to apply David A.'s bug fix and run with that rather than make everyone wait another whole release for this feature. Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Sudeep Holla 提交于
Currently ARM CPUs DT bindings allows different enable-method value for PSCI based systems. On ARM 64-bit this property is required and must be "psci" while on ARM 32-bit systems this property is optional and must be "arm,psci" if present. However, "arm,psci" has always been the compatible string for the PSCI node, and was never intended to be the enable-method. So this is a bug in the binding and not a deliberate attempt at specifying 32-bit differently. This is problematic if 32-bit OS is run on 64-bit system which has "psci" as enable-method rather than the expected "arm,psci". So let's unify the value into "psci" and remove support for "arm,psci" before it finds any users. Reported-by: NSoby Mathew <Soby.Mathew@arm.com> Cc: Rob Herring <robh+dt@kernel.org> Acked-by: NMark Rutland <mark.rutland@arm.com> Acked-by: NLorenzo Pieralisi <lorenzo.pieralisi@arm.com> Signed-off-by: NSudeep Holla <sudeep.holla@arm.com> Signed-off-by: NArnd Bergmann <arnd@arndb.de>
-
由 Eric Dumazet 提交于
When multiple skb are TX-completed in a row, we might incorrectly keep a timestamp of a prior skb and cause extra work. Fixes: ec693d47 ("net/mlx4_en: Add HW timestamping (TS) support") Signed-off-by: NEric Dumazet <edumazet@google.com> Cc: Willem de Bruijn <willemb@google.com> Reviewed-by: NEran Ben Elisha <eranbe@mellanox.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Ivan Babrou 提交于
Signed-off-by: NIvan Babrou <ivan@cloudflare.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-