A malicious VF might try to starve the other VFs & PF by creating
contineous doorbell floods. In order to negate this, HW has a threshold of
doorbells per client, which will stop the client doorbells from arriving
if crossed.

The threshold currently configured for VFs is too low - under extreme traffic
scenarios, it's possible for a VF to reach the threshold and thus for its
fastpath to stop working.
Signed-off-by: NAriel Elior <ariel.elior@qlogic.com>
Signed-off-by: NYuval Mintz <yuval.mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If L2FW utilized by the UNDI driver has the same version number as that
of the regular FW, a driver loading after UNDI and receiving an uncommon
answer from management will mistakenly assume the loaded FW matches its
own requirement and try to exist the flow via FLR.
Signed-off-by: NYuval Mintz <yuval.mintz@qlogic.com>
Signed-off-by: NAriel Elior <ariel.elior@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Set the phy access mode even in case of link-flap avoidance.
Signed-off-by: NYaniv Rosner <yaniv.rosner@qlogic.com>
Signed-off-by: NYuval Mintz <yuval.mintz@qlogic.com>
Signed-off-by: NAriel Elior <ariel.elior@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This avoids clearing the RX polarity setting in KR mode when polarity lane
is swapped, as otherwise this will result in failed link.
Signed-off-by: NYaniv Rosner <yaniv.rosner@qlogic.com>
Signed-off-by: NYuval Mintz <yuval.mintz@qlogic.com>
Signed-off-by: NAriel Elior <ariel.elior@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The SYSTEMPORT driver uses libphy to determine the carrier state, so
make sure we start with a carrier off until libphy has completed the
link training process.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The comment about how the hardware prepends 2bytes to align the IP
header on a 4-byte boundary was not correct, fix that.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We were missing an and comparison with status to check whether
RX_STATUS_OVFLOW is asserted or not in the per-packet status word, fix
that.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Our transmit locking scheme did not account for the TX ring full
interrupt. If a TX ring full interrupt fires while we are attempting to
transmit, we will cause a deadlock to occur. Fix this by making sure
that we properly disable interrupts while acquiring the spinlock.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A rmb() is required to ensure that the CQE is not read before it
is written by the adapter DMA.  PCI ordering rules will make sure
the other fields are written before the marker at the end of struct
eth_fast_path_rx_cqe but without rmb() a weakly ordered processor can
process stale data.

Without the barrier we have observed various crashes including
bnx2x_tpa_start being called on queues not stopped (resulting in message
start of bin not in stop) and NULL pointer exceptions from bnx2x_rx_int.
Signed-off-by: NMilton Miller <miltonm@us.ibm.com>
Signed-off-by: NWen Xiong <wenxiong@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When injecting EEH error to bnx2x adapter, adapter couldn't be recovery
and caused recursive EEH errors. The patch fixes the issue.
Signed-off-by: NWen Xiong <wenxiong@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The iSCSI netlink message needs to be sent before the ulp_ops is cleared
as it is sent through a function pointer in the ulp_ops.  This bug
causes iscsid to not get the message when the bnx2i driver is unloaded.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We are allocating memory with GFP_KERNEL under spinlock.  Since this is
the only call manipulating the cnic_udev_list and it is always under
rtnl_lock, cnic_dev_lock can be safely removed.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Because the called function, such as bnx2fc_indicate_netevent(), can sleep,
we cannot take rcu_lock().  To prevent the rcu protected ulp_ops from going
away, we use the cnic_lock mutex and set the ULP_F_CALL_PENDING flag.
The code already waits for ULP_F_CALL_PENDING flag to clear in
cnic_unregister_device().
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

ETHTOOL_{G,S}RXFHINDIR and ETHTOOL_{G,S}RSSH should work for drivers
regardless of whether they expose the hash key, unless you try to
set a hash key for a driver that doesn't expose it.
Signed-off-by: NBen Hutchings <ben@decadent.org.uk>
Acked-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch remove variables that are initialized with a constant,
are never updated, and are only used as parameter of return.
Return the constant instead of using a variable.

Verified by compilation only.

The coccinelle script that find and fixes this issue is:
// <smpl>
@@
type T;
constant C;
identifier ret;
@@
- T ret = C;
... when != ret
    when strict
return
- ret
+ C
;
// </smpl>
Signed-off-by: NPeter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

To fix:

  CC      drivers/net/ethernet/broadcom/bcmsysport.o
In file included from drivers/net/ethernet/broadcom/bcmsysport.c:28:0:
drivers/net/ethernet/broadcom/bcmsysport.h:41:8: error: redefinition of 'struct tsb'
arch/sparc/include/asm/mmu_64.h:65:8: note: originally defined here
make[1]: *** [drivers/net/ethernet/broadcom/bcmsysport.o] Error 1

we change struct tsb to struct bcm_tsb in the broadcom driver in
order to avoid the namespace collision.  For consistency, we also
change struct rsb to struct bcm_rsb, so the Rx/Tx symmetry is
maintained.
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The bnx2x development team has transferred from Broadcom to Qlogic.
This patch updates some obsolete email addresses to usable ones.
The bnx2x files contain headers with legal information from
Broadcom. Qlogic Legal depratment is taking their time coming up
with their own legal info. So this patch only updates contact
information. I will follow up with a patch for the headers once I
have the required info.
Signed-off-by: NAriel Elior <ariel.elior@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When cable is not present the clock speed of some of the devices is
reduced based upon power saving mode setting in NVRAM. Due to this
NVRAM reads take long time to complete as a result CPU soft lockup
message is seen. Fix is to override clock, disable link aware and link
idle modes before NVRAM reads and restore them back after the reads
are complete. During this period also check if the thread needs to be
rescheduled and if there are any signals to handle.

Also decrease the NVRAM command execution timeout value to 1ms.
Signed-off-by: NPrashant Sreedharan <prashant@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

o min_tx_rate puts lower limit on the VF bandwidth. VF is guaranteed
  to have a bandwidth of at least this value.
  max_tx_rate puts cap on the VF bandwidth. VF can have a bandwidth
  of up to this value.

o A new handler set_vf_rate for attr IFLA_VF_RATE has been introduced
  which takes 4 arguments:
  netdev, VF number, min_tx_rate, max_tx_rate

o ndo_set_vf_rate replaces ndo_set_vf_tx_rate handler.

o Drivers that currently implement ndo_set_vf_tx_rate should now call
  ndo_set_vf_rate instead and reject attempt to set a minimum bandwidth
  greater than 0 for IFLA_VF_TX_RATE when IFLA_VF_RATE is not yet
  implemented by driver.

o If user enters only one of either min_tx_rate or max_tx_rate, then,
  userland should read back the other value from driver and set both
  for IFLA_VF_RATE.
  Drivers that have not yet implemented IFLA_VF_RATE should always
  return min_tx_rate as 0 when read from ip tool.

o If both IFLA_VF_TX_RATE and IFLA_VF_RATE options are specified, then
  IFLA_VF_RATE should override.

o Idea is to have consistent display of rate values to user.

o Usage example: -

  ./ip link set p4p1 vf 0 rate 900

  ./ip link show p4p1
  32: p4p1: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode
  DEFAULT qlen 1000
    link/ether 00:0e:1e:08:b0:f0 brd ff:ff:ff:ff:ff:ff
    vf 0 MAC 3e:a0:ca:bd:ae:5a, tx rate 900 (Mbps), max_tx_rate 900Mbps
    vf 1 MAC f6:c6:7c:3f:3d:6c
    vf 2 MAC 56:32:43:98:d7:71
    vf 3 MAC d6:be:c3:b5:85:ff
    vf 4 MAC ee:a9:9a:1e:19:14
    vf 5 MAC 4a:d0:4c:07:52:18
    vf 6 MAC 3a:76:44:93:62:f9
    vf 7 MAC 82:e9:e7:e3:15:1a

  ./ip link set p4p1 vf 0 max_tx_rate 300 min_tx_rate 200

  ./ip link show p4p1
  32: p4p1: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode
  DEFAULT qlen 1000
    link/ether 00:0e:1e:08:b0:f0 brd ff:ff:ff:ff:ff:ff
    vf 0 MAC 3e:a0:ca:bd:ae:5a, tx rate 300 (Mbps), max_tx_rate 300Mbps,
    min_tx_rate 200Mbps
    vf 1 MAC f6:c6:7c:3f:3d:6c
    vf 2 MAC 56:32:43:98:d7:71
    vf 3 MAC d6:be:c3:b5:85:ff
    vf 4 MAC ee:a9:9a:1e:19:14
    vf 5 MAC 4a:d0:4c:07:52:18
    vf 6 MAC 3a:76:44:93:62:f9
    vf 7 MAC 82:e9:e7:e3:15:1a

  ./ip link set p4p1 vf 0 max_tx_rate 600 rate 300

  ./ip link show p4p1
  32: p4p1: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode
  DEFAULT qlen 1000
    link/ether 00:0e:1e:08:b0:f brd ff:ff:ff:ff:ff:ff
    vf 0 MAC 3e:a0:ca:bd:ae:5, tx rate 600 (Mbps), max_tx_rate 600Mbps,
    min_tx_rate 200Mbps
    vf 1 MAC f6:c6:7c:3f:3d:6c
    vf 2 MAC 56:32:43:98:d7:71
    vf 3 MAC d6:be:c3:b5:85:ff
    vf 4 MAC ee:a9:9a:1e:19:14
    vf 5 MAC 4a:d0:4c:07:52:18
    vf 6 MAC 3a:76:44:93:62:f9
    vf 7 MAC 82:e9:e7:e3:15:1a
Signed-off-by: NSucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

of_phy_connect_fixed_link() is becoming obsolete, and also required
platform code to register the fixed PHYs at the specified addresses for
those to be usable. Get rid of it and use the new of_phy_is_fixed_link()
plus of_phy_register_fixed_link() helpers to transition over the new
scheme.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

of_phy_connect_fixed_link() is becoming obsolete, and also required
platform code to register the fixed PHYs at the specified addresses for
those to be usable. Get rid of it and use the new of_phy_is_fixed_link()
plus of_phy_register_fixed_link() helpers to transition over the new
scheme.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

These "return 0;" uses seem wrong as there are
rc variables where error return values are set
but unused.
Signed-off-by: NJoe Perches <joe@perches.com>
Acked-by: NDmitry Kravkov <Dmitry.Kravkov@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When umac_enable_set() is used to disable the UniMAC receiver or
transmitter, we need to make sure that we wait for a full-sized packet
to be processed because the UniMAC hardware stops on a packet boundary,
not immediately.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

dma_unmap_single() was called with dma_unmap_len(cb, dma_len),
unfortunately we failed to assign this length field in
bcm_sysport_rx_refill() or bcm_sysport_alloc_rx_bufs() using
dma_unmap_len_set().

This causes packet contents corruption because are we not invoking the
cache invalidation routines with the proper length.  Fix this by using
the full RX buffer size (RX_BUF_LENGTH) because the mappings for the RX
bufers are created with that size.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Packets need to be at least 64 bytes to enter the switch port logic,
including the FCS, otherwise they will be discarded as RUNT packets.

With packets having Broadcom tags, the 4-bytes tag is first stripped
off the packet, and the packet length is then checked, so we need to
make sure that the packet length with FCS is at least 64 bytes.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The link adjustment callback can be called as frequently as desired by
the PHY library, as such, let's avoid doing a Read/Modify/Write sequence
if nothing changed, which is more than likely since we are interfaced
with a switch device.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use devm_ioremap_resource() because devm_request_and_ioremap() is
obsoleted by devm_ioremap_resource().
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Acked-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If any TSO fragment hits hardware bug conditions (e.g. 4G boundary), the
driver will workaround by calling skb_copy() to copy to a linear SKB.  Users
have reported page allocation failures as the TSO packet can be up to 64K.
Copying such a large packet is also very inefficient.  We fix this by using
existing tg3_tso_bug() to transmit the packet using GSO.
Signed-off-by: NPrashant Sreedharan <prashant@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

tg3 uses GSO as workaround if the hardware cannot perform TSO on certain
packets.  We should not modify the ip header fields if we do GSO on the
packet.  It happens to work by accident because GSO recalculates the IP
checksum and IP total length.

Also fix the tg3_start_xmit comment to reflect that this is the only
xmit function for all devices.
Signed-off-by: NPrashant Sreedharan <prashant@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

net: get rid of SET_ETHTOOL_OPS

Dave Miller mentioned he'd like to see SET_ETHTOOL_OPS gone.
This does that.

Mostly done via coccinelle script:
@@
struct ethtool_ops *ops;
struct net_device *dev;
@@
-       SET_ETHTOOL_OPS(dev, ops);
+       dev->ethtool_ops = ops;

Compile tested only, but I'd seriously wonder if this broke anything.
Suggested-by: NDave Miller <davem@davemloft.net>
Signed-off-by: NWilfried Klaebe <w-lkml@lebenslange-mailadresse.de>
Acked-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix build when BNX2X_SRIOV is not enabled.
Change one parameter struct from bnx2 to bnx2x and don't return a value
from a void function.

drivers/net/ethernet/broadcom/bnx2x/bnx2x_sriov.h:576:48: warning: 'struct bnx2' declared inside parameter list [enabled by default]
drivers/net/ethernet/broadcom/bnx2x/bnx2x_sriov.h:576:48: warning: its scope is only this definition or declaration, which is probably not what you want [enabled by default]

drivers/net/ethernet/broadcom/bnx2x/bnx2x_sriov.h:576:60: warning: 'return' with a value, in function returning void [enabled by default]
Signed-off-by: NRandy Dunlap <rdunlap@infradead.org>
Cc:	Ariel Elior <ariele@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 91ebb928b "bnx2x: Add support for Multi-Function UNDI" contains a bug
which prevent the emptying of the device's Rx buffers before reset.
As a result, on new boards it is likely HW will reach some fatal assertion
once its interfaces load after UNDI was previously loaded.
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NAriel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Hook the Broadcom SYSTEMPORT driver into the build system under the
SYSTEMPORT Kconfig symbol.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

SYSTEMPORT is the latest Ethernet MAC hardware block used on newer
BCM7xxx Set Top Box SoCs in conjunction with an internal Ethernet
switch. This patch adds support for this hardware block along with the
following hardware features:

- support for hardware checksum offload (transmit and receive)
- support for the 32 transmit queues
- MIB counters reading
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 2dc33bbc "bnx2x: Remove the sriov VFOP mechanism" caused a regression,
preventing VFs from configuring multicast filters.
Signed-off-by: NNaredner Kumar <narender.kumar@qlogic.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NAriel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Starting with commit 2dc33bbc "bnx2x: Remove the sriov VFOP mechanism",
the bnx2x started enforcing vlan credits for all vlan configurations.
This exposed 2 issues:
  - Vlan credits are not returned once a VF is removed; this causes a leak
    of credits, and eventually will lead to VFs with no vlan credits.
  - A vlan credit must be set aside for the Hypervisor to use, and should
    not be visible to the VF.

Although linux VFs at the moment do not support vlan configuration [from the
VF side] which causes them to be resilient to this sort of issue, Windows VF
over linux hypervisors might fail to load as the vlan credits become depleted.
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NAriel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When removing a VF interface, the driver fails to release that VF's mailbox
and bulletin board allocated memory.
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NAriel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use the ARRAY_SIZE macro to determine the number of entries in
bcm_enet_gstrings_stats.
Signed-off-by: NTobias Klauser <tklauser@distanz.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>