A malicious VF might try to starve the other VFs & PF by creating
contineous doorbell floods. In order to negate this, HW has a threshold of
doorbells per client, which will stop the client doorbells from arriving
if crossed.

The threshold currently configured for VFs is too low - under extreme traffic
scenarios, it's possible for a VF to reach the threshold and thus for its
fastpath to stop working.
Signed-off-by: NAriel Elior <ariel.elior@qlogic.com>
Signed-off-by: NYuval Mintz <yuval.mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If L2FW utilized by the UNDI driver has the same version number as that
of the regular FW, a driver loading after UNDI and receiving an uncommon
answer from management will mistakenly assume the loaded FW matches its
own requirement and try to exist the flow via FLR.
Signed-off-by: NYuval Mintz <yuval.mintz@qlogic.com>
Signed-off-by: NAriel Elior <ariel.elior@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Set the phy access mode even in case of link-flap avoidance.
Signed-off-by: NYaniv Rosner <yaniv.rosner@qlogic.com>
Signed-off-by: NYuval Mintz <yuval.mintz@qlogic.com>
Signed-off-by: NAriel Elior <ariel.elior@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This avoids clearing the RX polarity setting in KR mode when polarity lane
is swapped, as otherwise this will result in failed link.
Signed-off-by: NYaniv Rosner <yaniv.rosner@qlogic.com>
Signed-off-by: NYuval Mintz <yuval.mintz@qlogic.com>
Signed-off-by: NAriel Elior <ariel.elior@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NShruti Kanetkar <Shruti@Freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Print the device address, the register number and the PHY ID for
which the MDIO read operation failed
Signed-off-by: NShruti Kanetkar <Shruti@Freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Need to gro_postpull_rcsum for GRO to work with checksum complete.
Signed-off-by: NTom Herbert <therbert@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NShahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

- Check interrupt mode at the start of qlcnic_set_channels().
- Do not validate ring count if they are not going to change.
Signed-off-by: NShahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pre-allocate the physically contiguous DMA buffer used for
minidump collection at driver load time, rather than at
run time, to minimize allocation failures. Driver will allocate
the buffer at load time if PEX DMA support capability is indicated
by the adapter.
Signed-off-by: NShahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We recently change the kzalloc() to devm_kzalloc() so freeing "ctlr"
here could lead to a double free.

Fixes: e1943128 ('drivers: net: davinci_cpdma: Convert kzalloc() to devm_kzalloc().')
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There is a typo here so we return directly instead of unwinding.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Acked-by: NTom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

adds the device managed APIs so that no need worry about
freeing the resources.
Signed-off-by: NVarka Bhadram <varkab@cdac.in>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fixes:ee45fd92
("sfc: Use TX PIO for sufficiently small packets")

The linux net driver uses memcpy_toio() in order to copy into
the PIO buffers.
Even on a 64bit machine this causes 32bit accesses to a write-
combined memory region.
There are hardware limitations that mean that only 64bit
naturally aligned accesses are safe in all cases.
Due to being write-combined memory region two 32bit accesses
may be coalesced to form a 64bit non 64bit aligned access.
Solution was to open-code the memory copy routines using pointers
and to only enable PIO for x86_64 machines.

Not tested on platforms other than x86_64 because this patch
disables the PIO feature on other platforms.
Compile-tested on x86 to ensure that works.

The WARN_ON_ONCE() code in the previous version of this patch
has been moved into the internal sfc debug driver as the
assertion was unnecessary in the upstream kernel code.

This bug fix applies to v3.13 and v3.14 stable branches.
Signed-off-by: NShradha Shah <sshah@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

commit e9ce7cb6 ("xen-netback: Factor queue-specific data into
queue struct") added a use of vzalloc/vfree to interface.c, but
removed the #include <linux/vmalloc.h> statement at the same time,
which causes this build error:

drivers/net/xen-netback/interface.c: In function 'xenvif_free':
drivers/net/xen-netback/interface.c:754:2: error: implicit declaration of function 'vfree' [-Werror=implicit-function-declaration]
  vfree(vif->queues);
  ^
cc1: some warnings being treated as errors
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Cc: Wei Liu <wei.liu2@citrix.com>
Cc: Andrew J. Bennieston <andrew.bennieston@citrix.com>
Acked-by: NWei Liu <wei.liu2@citrix.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Using phy_drivers_register/_unregister functions is proper way to
handle multiple PHY drivers registration. For Realtek PHY drivers
module, it fixes incomplete current error-handlings up and adds
missed unregistration for the RTL8201CP driver.
Signed-off-by: NJongsung Kim <neidhard.kim@lge.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes an issue that we cannot use nfs rootfs correctly
on r8a7790 when the command below runs on a host PC.

 $ sudo ping -f -l 8 $BOARD_IP_ADDR

Since the driver sets the RACT to 1 in the first while loop of
sh_eth_rx(), the controller accepts a next frame into the next RX
descriptor during the while loop. But, in the first while loop
doesn't allocate a next skb. So, this patch removes the RACT setting
in the first while loop of sh_eth_rx().
Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes the packet "exceeded" condition in sh_eth_rx() when
RACT in an RX descriptor is not set and the "quota" is 0.
Otherwise, kernel panic happens because the "&n->poll_list" is deleted
twice in sh_eth_poll() which calls napi_complete() and net_rx_action().
Signed-off-by: NKouei Abe <kouei.abe.cp@renesas.com>
Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The SXGBE_CORE_L34_ADDCTL_REG define is cut and pasted twice so we can
delete the second instance.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The QLC_83XX_GET_LSO_CAPABILITY define is cut and pasted twice so we can
delete the second instance.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Acked-by: NSony Chacko <sony.chacko@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The “affinity hint” mechanism is used by the user space
daemon, irqbalancer, to indicate a preferred CPU mask for irqs.
Irqbalancer can use this hint to balance the irqs between the
cpus indicated by the mask.

We wish the HCA to preferentially map the IRQs it uses to numa cores
close to it.  To accomplish this, we use cpumask_set_cpu_local_first(), that
sets the affinity hint according the following policy:
First it maps IRQs to “close” numa cores.  If these are exhausted, the
remaining IRQs are mapped to “far” numa cores.
Signed-off-by: NYuval Atias <yuvala@mellanox.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Bump versions.

Change-ID: Ic4a84354955061ca18321b1e97c9c30fe1563b5c
Signed-off-by: NCatherine Sullivan <catherine.sullivan@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

No need to read the PCI register for the PF's base queue on every single Tx
queue enable and disable as we already have the value stored from reading
the capability features at startup.

Change-ID: Ic02fb622757742f43cb8269369c3d972d4f66555
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

A drop action comes down as a ring_cookie value, so allow it as
a special value that can be used to configure destination control.

Also fix the output to filter read command accordingly.

Change-ID: I9956723cee42f3194885403317dd21ed4a151144
Signed-off-by: NAnjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add members to stat struct to keep track of Flow director ATR and
SideBand filter packet matches.

Change-ID: Ibbb31a53c7adcc2bb96991dd80565442a2f2513c
Signed-off-by: NAnjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change drops the FTYPE field from the Rx descriptor, to
match the hardware implementation.

Change-ID: I66d31d2b43861da45e8ace4fb03df033abe88bab
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

FW can indicate any admin queue error states to the driver via some bits
in the length registers. Each time we process an admin queue message,
check these bits and log any errors we find. Since the VF really can't
do much, we just print the message and depend on the PF driver to clear
things up on our behalf.

Change-ID: I92bc6c53ce3b4400544e0ca19c5de2d27490bd0d
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Linux gives us a function to copy Ethernet MAC addresses, let's use it.

Change-ID: I0c861900029ca5ea65a53ca39565852fb633f6fd
Signed-off-by: NGreg Rose <gregory.v.rose@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Remove the filter created by the firmware with the default MAC address it
reads out of the NVM storage and a promiscuous VLAN tag and replace it
with a filter that will not accept tagged packets by default.  The system
must request a VLAN tag packet filter to get packets with that tag.

Change-ID: I119e6c3603a039bd68282ba31bf26f33a575490a
Signed-off-by: NGreg Rose <gregory.v.rose@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Currently if the firmware reports DCB capability the driver enables
I40E_FLAG_DCB_ENABLED flag. When this flag is enabled the driver
inserts a tag when transmitting a packet from the port even if there
are no DCB traffic classes configured at the port.

This patch adds a new flag I40E_FLAG_DCB_CAPABLE that will be set
when the DCB capability is present and the existing flag
I40E_FLAG_DCB_ENABLED will be set only if there are more than one
traffic classes configured at the port.

Change-ID: I24ccbf53ef293db2eba80c8a9772acf729795bd5
Signed-off-by: NNeerav Parikh <neerav.parikh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

If the device is down, there's no place to go but up, so don't try to go
down even more. This prevents a CPU soft lock in napi_disable().

Change-ID: I8b058b9ee974dfa01c212fae2597f4f54b333314
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

In XL710 devices we program FD filter's fields from Tx perspective of the flow.
However the user interface exposed in ethtool should be compliant with the
previous generation of drivers where a filter src and dst field are from
the RX perspective. This patch changes the ethtool interface in this regard
to match the other drivers.

Change-ID: Iec6ccddd87357c4fb53ccf33aa0fae699faf70cf
Signed-off-by: NAnjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add set_pf_context, replace set_phy_reset with set_phy_debug, add
nvm_config_read/write, remove nvm_read/write_reg_se and add some
PHY types.

With these changes we bump the API version to 1.2.

Change-ID: I4dc3aec175c2316f66fc9b726b3f7d594699d84e
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Set appropriate fields in Tx queue configuration virtchnl message
to pf to enable headwb and setup headwb addr.
Then use that info from the VF to set headwb and headwb_addr instead of
always enabling them.

Change-ID: I7d393d1b2b07f0f3355b3a4f7c2d3c6ee3b0d622
Signed-off-by: NAshish Shah <ashish.n.shah@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch separates the hardware logic from the set function, so that
we can re-use it during a ptp_reset. This enables the reset to return
functionality to the last known timestamp mode, rather than resetting
the value. We initialize the mode to off during the ptp_init cycle.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Return a 0 directly rather than a constant.
Reported-by: NPeter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: NTodd Fujinaka <todd.fujinaka@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

MAX_DMA_CHANNELS is defined in asm/scatterlist.h of the powerpc
architecture.  Rename this #define in xgbe.h to avoid the
redefined warning issued during compilation.
Reported-by: NFengguang Wu <fengguang.wu@intel.com>
Signed-off-by: NTom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use dma_addr_t for DMA address parameters and u32 for shared memory
offset parameters.

Do not assume that dma_addr_t is the same as unsigned long; it will
not be in PAE configurations.  Truncate DMA addresses to 32 bits when
printing them.  This is OK because the DMA mask for this device is
32-bit (per default).

Also rename the DMA address parameters from 'skb' to 'dma'.

Compile-tested only.
Signed-off-by: NBen Hutchings <ben@decadent.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Following commit befdf897 "net/mlx4_core: Preserve pci_dev_data after
__mlx4_remove_one()", there are two mlx4 pci callbacks which will
attempt to release the mlx4_priv object -- .shutdown and .remove.

This leads to a use-after-free access to the already freed mlx4_priv
instance and trigger a "Kernel access of bad area" crash when both
.shutdown and .remove are called.

During reboot or kexec, .shutdown is called, with the VFs probed to
the host going through shutdown first and then the PF. Later, the PF
will trigger VFs' .remove since VFs still have driver attached.

Fix that by keeping only one driver entry which releases mlx4_priv.

Fixes: befdf897 ('net/mlx4_core: Preserve pci_dev_data after __mlx4_remove_one()')
CC: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NWei Yang <weiyang@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The Hypervisor driver tracks free slots and reserved slots at the global level
and tracks allocated slots and guaranteed slots per VF.

Guaranteed slots are treated as reserved by the driver, so the total
reserved slots is the sum of all guaranteed slots over all the VFs.

As VFs allocate resources, free (global) is decremented and allocated (per VF)
is incremented for those resources. However, reserved (global) is never changed.

This means that effectively, when a VF allocates a resource from its
guaranteed pool, it is actually reducing that resource's free pool (since
the global reserved count was not also reduced).

The fix for this problem is the following: For each resource, as long as a
VF's allocated count is <= its guaranteed number, when allocating for that
VF, the reserved count (global) should be reduced by the allocation as well.

When the global reserved count reaches zero, the remaining global free count
is still accessible as the free pool for that resource.

When the VF frees resources, the reverse happens: the global reserved count
for a resource is incremented only once the VFs allocated number falls below
its guaranteed number.

This fix was developed by Rick Kready <kready@us.ibm.com>
Reported-by: NRick Kready <kready@us.ibm.com>
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>