This adds a driver for the SPI connected AK4104 S/PDIF transmitter
device. Its features are fairly simple, but as there is need to set up
certain bits in the IEC958 information, this better goes into a real
driver.
Signed-off-by: NDaniel Mack <daniel@caiaq.de>
Cc: Mark Brown <broonie@sirena.org.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Removes numbers from the list of features/limitations and makes it
reflect recent changes to the code.
Signed-off-by: NDaniel Mack <daniel@caiaq.de>
Acked-by: NTimur Tabi <timur@freescale.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Add support for true pause and unpause.  Without this, mplayer will drop some
audio (less than one second, but still noticeable) when pausing playback.

Remove support for PM suspend and resume from the trigger function, since the
driver doesn't support PM anyway.

Optimize the delay after starting capture.  Instead of delaying 1ms, the driver
now polls the hardware.  The new delay is shorter by over 90% yet still
effective.
Signed-off-by: NTimur Tabi <timur@freescale.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NHugo Villeneuve <hugo@hugovil.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Upgrade the severity of some failure messages from debug level so
they're displayed by default.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

The recent set of S3C64xx patches re-added a lot of uses of DBG() that
had previously been removed - revert this so the standard pr_debug()
macro is used.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Reported-by: NRob Maris <maris.rob@vdi.de>
Signed-off-by: NMike Frysinger <vapier.adi@gmail.com>
Signed-off-by: NBryan Wu <cooloney@kernel.org>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NMike Frysinger <vapier.adi@gmail.com>
Signed-off-by: NBryan Wu <cooloney@kernel.org>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Add headset jack detection for SDP3430 boards using SoC jack
reporting interface. Headset detection on SDP3430 board is
achieved through TWL4030 GPIO_2 pin.
Signed-off-by: NMisael Lopez Cruz <x0052729@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Add a new device tree property for the SSI node: "fsl,ssi-asynchronous".  If
defined, the SSI is programmed into asynchronous mode, otherwise it is
programmed into synchronous mode.  In asynchronous mode, pin SRCK must be
connected to the same clock source as STFS, and pin SRFS must be connected to
the same signal as STFS.  Asynchronous mode allows playback and capture to
use different sample sizes.  It also technically allows different sample rates,
but the driver does not support that.
Signed-off-by: NTimur Tabi <timur@freescale.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

We now support the 64xx series as well as the 24xx series - make sure
people using Kconfig know this.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

snd_soc_dapm_switch ends up ends up in dapm_new_mixer() (since a switch
is a special case of a mixer with only one input) but this wasn't
correctly handled in the code.

Also fix the coding style for the switch below while we're here.
Reported-by: NJoonyoung Shim <dofmind@gmail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Essentially simple code motion to facilitate refactoring of the power
decisions.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

A bit in PXA's SSCR0 register was erroneously named ADC but its name is
in fact ACS (audio clock select).
Signed-off-by: NDaniel Mack <daniel@caiaq.de>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Enum type for selecting the desired ramp delay for the headset output.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Remove uneeded startup callback and use snd_soc_dapm_nc_pin()
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Select the relevant DMA implementation when the
sound driver is selected.
Signed-off-by: NBen Dooks <ben@simtec.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Add the initial code to support the S3C64XX I2S hardware using the
s3c-i2s-v2 core code.
Signed-off-by: NBen Dooks <ben@simtec.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

The S3C2412 I2S (IIS) interface is replicated on further Samsung SoC
parts in a broadly compatible way, so split the common code out into
a core called s3c-i2s-v2.[ch] so that the newer SoCs such as the
S3C6410 can make use of it.

As such, all the original s3c2412 functions are currently being left
with their original names, and will be renamed later in the series.
Signed-off-by: NBen Dooks <ben@simtec.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Add support for the Jive's WM8750 codec attached via the S3C2412 IIS.
Signed-off-by: NBen Dooks <ben@simtec.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Add DAPM machine domain widgets to SDP3430 machine driver.
Interconnection:
* Ext Mic: MAINMIC, SUBMIC
* Ext Spk: HFL, HFR
* Headset Jack: HSMIC, HSOL, HSOR
Signed-off-by: NMisael Lopez Cruz <x0052729@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

The <mach/audio.h> file needs to be common to both ARCH_S3C2410 and
ARCH_S3C64XX as they share common driver code, so move it to <plat/audio.h>.
Signed-off-by: NBen Dooks <ben@simtec.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Move the IIS headers to their correct place.
Signed-off-by: NBen Dooks <ben@simtec.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

When setting WM8510_MCLKDIV the pll was turned off.

When setting pll frequency you got twice the expected freq, because
the  code calculated  with postscaler of 8,  but  the hardware divide by 4.
Signed-off-by: NJonas Andersson <jonas@microbit.se>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Add GPIO support to jack reporting framework in ASoC using gpiolib calls.
The gpio support exports two new functions: snd_soc_jack_add_gpios and
snd_soc_jack_free_gpios.

Client drivers using gpio feature must pass an array of jack_gpio pins
belonging to a specific jack to the snd_soc_jack_add_gpios function. The
framework will request the gpios, set the data direction and request irq.
The framework will update power status of related jack_pins when an event on
the gpio pins comes according to the reporting bits defined for each gpio.

All gpio resources allocated when adding jack_gpio pins can be released
using snd_soc_jack_free_gpios function.
Signed-off-by: NMisael Lopez Cruz <x0052729@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Only allow SND_SOC_DAIFMT_CBS_CFS for the playback DAI.
Signed-off-by: NPhilipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

For consistency with 24-bit and 32-bit modes, don't send 16-bit stereo
in one 32-bit transfer. Use 2 slots instead on Zylonite. It should result
in exactly the same behaviour.
Now it is possible to use 16-bit single slot transfers in pxa-ssp, which
are needed for Magician to get two frame clock pulses per sample
(one for each channel).
Signed-off-by: NPhilipp Zabel <philipp.zabel@gmail.com>
Tested-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

If the UDA1380's interpolator or decimator are set to be clocked from
the WSPLL (which syncs to the WSI signal), the DAI link must be running
to change the interpolator/decimator registers (which include volume
controls and digital mute setting).

* Queue work in the alsa PCM_START .trigger to flush registers
  as soon as the link is running. This replaces the .prepare
  and .digital_mute callbacks.
* Use the SILENCE override instead of MTM for muting and remove
  its alsa control to avoid confusion.
Signed-off-by: NPhilipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NPhilipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

This removes a misspelled comment and got rid of superfluous switch
case.
Signed-off-by: NDaniel Mack <daniel@caiaq.de>
Acked-by: NTimur Tabi <timur@freescale.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

On some systems it is desirable for control for DAPM pins to be provided
to user space. This is the case with things like GSM modems which are
controlled primarily from user space, for example. Provide a helper which
exposes the state of a DAPM pin to user space for use in cases like this.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Added support for scenarios where the Cirrus CS4270 audio codec is slave
to the bitclk and lrclk. Mixed setups are unsupported.
Signed-off-by: NDaniel Mack <daniel@caiaq.de>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Fix the copyright statements in two of the S3C24XX ASoC files
that have (c) when we require the full word.
Signed-off-by: NBen Dooks <ben@simtec.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

sound/soc/codecs/wm8753.c: In function 'wm8753_probe':
sound/soc/codecs/wm8753.c:1577: error: implicit declaration of function 'wm8753_add_controls'
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

This will reduce the number of writes done on resume, allowing that to
complete faster (especially on systems with very slow I2C like the
current Samsung driver).
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

The base support for the only in-tree user, the GTA01, is out of tree
and will be updated separately.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

This patch should be pure code motion, separating that out from the
functional changes to move to new style device registration.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

We always run in the first timeslot of one.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>