Conflicts:
	drivers/net/can/Kconfig

ks8695_rx() will call refill_buffers() for every incoming packet.
Its not necessary. We just need do it after finishing receiving thing.
And the 'RX dma engine' is in the same situation.
This blocks our user space application. The following patch may fix it.
Signed-off-by: Nzeal <zealcook@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

ks8695 rx irq is edge-level. Before arriving at irq handler, the
corresponding status bit has been clear(irq's ack).
So we should not check it after that.
Signed-off-by: Nzeal <zealcook@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

PPP does not correctly call pskb_may_pull() on all necessary receive paths
before reading the PPP protocol, thus causing PPP to report seemingly
random 'unsupported protocols' and eventually trigger BUG_ON(skb->len <
skb->data_len) in skb_pull_rcsum() when receiving multilink protocol in
non-linear skbs.

ppp_receive_nonmp_frame() does not call pskb_may_pull() before reading the
protocol number.  For the non-mp receive path this is not a problem, as
this check is done in ppp_receive_frame().  For the mp receive path,
ppp_mp_reconstruct() usually copies the data into a new linear skb.
However, in the case where the frame is made up of a single mp fragment,
the mp header is pulled and the existing skb used.  This skb was then
passed to ppp_receive_nonmp_frame() without checking if the encapsulated
protocol header could safely be read.
Signed-off-by: NBen McKeegan <ben@netservers.co.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After commmit 4b77b0a2 EEH breaks
after the second error, since it calls pci_restore_state()
but it returns 0, since pci->state_saved is false.

So, this patch just call pci_save_state() after pci_restore_state().
Signed-off-by: NBreno Leitao <leitao@linux.vnet.ibm.com>
Acked-by: NPeter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

net: Fix the rollback test in dev_change_name()

In dev_change_name() an err variable is used for storing the original
call_netdevice_notifiers() errno (negative) and testing for a rollback
error later, but the test for non-zero is wrong, because the err might
have positive value as well - from dev_alloc_name(). It means the
rollback for a netdevice with a number > 0 will never happen. (The err
test is reordered btw. to make it more readable.)
Signed-off-by: NJarek Poplawski <jarkao2@gmail.com>
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Technically there is no need to set the card offline to change
RX checksumming. Get rid of this stupid limitation.
Signed-off-by: NFrank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The maximum TSO size OSA can handle is 15 * PAGE_SIZE. This
patch reduces gso_max_size to this value and adds some sanity
checks and statistics to the TSO implementation.
Since only layer 3 is able to do TSO move all TSO related functions
to the qeth_l3 module.
Signed-off-by: NFrank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Setting a qeth device online requires to call function
ccw_device_set_online() for read-, write-, and data-subchannel.
Failures should be detected immediately without an attempt to
invoke follow-on activity qeth_qdio_clear_card().,

In addition, ccw_device_set_online calls are consolidated in
qeth_core_main.c only.
Signed-off-by: NUrsula Braun <ursula.braun@de.ibm.com>
Signed-off-by: NFrank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

EDDP code has been removed from qeth in 2009. This patch removes two
useless remaining EDDP-references.
Signed-off-by: NUrsula Braun <ursula.braun@de.ibm.com>
Signed-off-by: NFrank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Isolate data connection to a shared OSA card against other data
connections to the same OSA card. Connectivity between isolated
data connections sharing the same OSA card is therefore possible only
through external network gear (e.g. a router).
Signed-off-by: NEinar Lueck <elelueck@de.ibm.com>
Signed-off-by: NFrank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This reverts commit 38783e67.

It causes kernel bugzilla #14594
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The function print_mac in net/ethernet/eth.c is marked __deprecated
and not used. Remove it.
Signed-off-by: NMarin Mitov <mitov@issp.bas.bg>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The language of 802.3ad 43.4.9 requires the "recordPDU" function
to, in part, compare the Partner parameter values in a received LACPDU
to the stored Actor values.  If those match, then the Partner's
synchronization state is set to true.

	The current 802.3ad implementation is performing these steps out
of order; first, the synchronization check is done, then the paramters are
checked to see if they match (the synch check being done against a match
check of a prior LACPDU).  This causes delays in establishing aggregators
in some circumstances.

	This patch modifies the 802.3ad code to call __choose_matched,
the function that does the "match" comparisions, as the first step of
__record_pdu, instead of immediately afterwards.  This new behavior is
in compliance with the language of the standard.

	Some additional commentary relating to code vs. standard is also
added.

	Reported by Martin Patterson <martin@gear6.com> who also supplied
the logic of the fix and verified the patch.
Signed-off-by: NJay Vosburgh <fubar@us.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 05423b24 (vlan: allow null VLAN ID to be used)
forgot to update __vlan_hwaccel_rx() & vlan_gro_common()

We need to set VLAN_TAG_PRESENT flag in skb->vlan_tci
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In the NAPI poll function(emac_poll), check for netif_running()
is unnecassary. In addition to associated runtime overhead, it
also results in a continuous softirq loop when the interface is
brought down under heavy traffic(tested wit Traffic Generator).
Once the interface is disabled, the poll function always returns
zero(with the check for netif_running) and napi_complete() would
never get called resulting in softirq loop.
Signed-off-by: NSriramakrishnan <srk@ti.com>
Acked-by: NChaithrika U S <chaithrika@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In the NAPI poll function, check for netif_running() is unnecassary.
In addition to associated runtime overhead, it also results in
continuous softirq loop when the interface is brought down under heavy
traffic(tested with Traffic Generator).Once the interface is disabled,
the poll function always returns zero(with the check for netif_running)
and napi_complete() would never get called resulting in softirq loop.
Signed-off-by: NSriramakrishnan <srk@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch updates the tg3 version to 3.104.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes the 5717 variant device ID enumerations and adds those
DIDs to the PCI ID table.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds code to funnel each MSI-X vector's rx packet buffers
into a single set of producer rings which will then be submitted to the
hardware.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The rx producer mailbox registers are used in several spots in the code.
The addition of TG3_64BIT_REG_LOW makes register references
uncomfortably long.  This patch creates an alias for the standard and
jumbo ring producer index registers to make the code cleaner.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The patch increases the number of producer rings available and
implements the constructor and destructor code that deals with them.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch changes how the code uses the rx_std_prod_idx member.  In the
following patch, the code will be changed so that it will act just like
a hardware mailbox.  This patch prepares the code so that memory barriers
can be more easily inserted.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A later patch is going to add consumer indicies for the producer rings.
To keep things readable, this patch renames rx_[std|jmb]_ptr to
rx_[std|jmb]_prod_idx.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch converts the tnapi argument of tg3_alloc_rx_skb() to tp.  The
level of indirection is unnecessary.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch changes the tg3_alloc_rx_skb() implementation to accept the
destination producer ring set pointer as a parameter rather than
assuming the source and destination producer rings are the same.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch removes the source index parameter of tg3_alloc_rx_skb().  A
later patch will make it possible for the source and destination
producer rings to be different.  This patch opts to make
tg3_alloc_rx_skb() a destination-only implementation and move the code
sensitive to the difference elsewhere.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

tg3_get_invariants(), among other things, discovers whether or not
the device is MSI-X capable and how many interrupts it supports.
This discovery needs to happen before registering NAPI instances with
netdev.  This patch moves the code block that calls napi_add later in
tg3_init_one() so that tg3_get_invariants() has a chance to run first.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch gives all non-zero MSIX vectors their own NAPI handler.  This
will make NAPI handling for those vectors slightly more efficient.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

By default, the 5717 (and future chips) break up PCIe DMA packets across
cacheline boundaries.  This isn't necessary on x86.  This patch
selectively loosens the restriction.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The A0 revision of the 5717 has problems with short packet fragments.
It needs to use the tg3_start_xmit_dma_bug() routine.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The 5717 sets up TSO slightly differently in the transmit path.  It
looks like this method will be the new way of doing things.  This patch
defines a flag to indicate this.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch consolidates the TSO capability discovery code into its own
code block.  The code that decides whether or not to allow TSO is then
cleaned up.  Finally, the patch consolidates all MSI and MSIX
capability code into a single code block.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We need room for another TSO flag and it would be most efficient if it
resided in tg3_flags2.  This patch moves the TG3_FLG2_PROTECTED_NVRAM
to tg3_flags3 to make room.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch converts tg3_start_xmit_dma_bug() to accomodate multiple NAPI
instances.  This is prep work for a later patch in this series.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch avoids reprogramming the RCB NIC addresses for all 5755 and
later devices.  The address is incorrect for 5717 devices and should be
correct by default for all other affected devices.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds the 5717 phy ID.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Recent changes in the TX error propagation require additional checking
and masking of values returned from hard_start_xmit(), mainly to
separate cases where skb was consumed. This aim can be simplified by
changing the order of NETDEV_TX and NET_XMIT codes, because the latter
are treated similarly to negative (ERRNO) values.

After this change much simpler dev_xmit_complete() is also used in
sch_direct_xmit(), so it is moved to netdevice.h.

Additionally NET_RX definitions in netdevice.h are moved up from
between TX codes to avoid confusion while reading the TX comment.
Signed-off-by: NJarek Poplawski <jarkao2@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

drop the version parts not needed for in-tree driver
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>