Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

The error handling for the mpc5200 fec interrupt is broken. The intended
behaviour is like this:

* If one of FEC_IEVENT_RFIFO_ERROR and FEC_IEVENT_XFIFO_ERROR happens,
  the datasheet says (MPC5200B User's Guide R1.2, p. 14-13): "When this
  occurs, software must ensure both the FIFO Controller and BestComm are
  soft-reset".

* On any other error (non-TFINT) interrupt, just issue a debug message.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

Add board support for the Phytec pcm030 mpc5200b based board. It
does not need any platform specific fixups and as such is handled
as a mpc5200 simple platform.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

This patch adds gpiolib support for mpc5200 SOCs.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

Add a set_type function for external (GPIO) interrupts.
Signed-off-by: NJuergen Beisert <j.beisert@pengutronix.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

If CONFIG_PPC_MPC5121 is not set, then the of_device_id table for the
mpc5200 serial driver will not get terminated with a NULL entry.
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

Change RapidIO doorbell source and target ID field to 16-bit for
support large system size, which max rio devid is 65535.
Signed-off-by: NZhang Wei <wei.zhang@freescale.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Signed-off-by: NZhang Wei <wei.zhang@freescale.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Signed-off-by: NZhang Wei <wei.zhang@freescale.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Signed-off-by: NZhang Wei <wei.zhang@freescale.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This adds properties describing the RapidIO controller to the
device-tree source for the MPC8641HPCN board.
Signed-off-by: NZhang Wei <wei.zhang@freescale.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

The RapidIO system size will auto probe in RIO setup.  The route table
and rionet_active in rionet.c are changed to be allocated dynamically
according to the size of the system.
Signed-off-by: NZhang Wei <wei.zhang@freescale.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This initializes the RapidIO controller driver using addresses and
interrupt numbers obtained from the firmware device tree, rather than
using hardcoded constants.
Signed-off-by: NZhang Wei <wei.zhang@freescale.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

The original RapidIO driver suppose there is only one mpc85xx RIO controller
in system.  So, some data structures are defined as mpc85xx_rio global, such
as 'regs_win', 'dbell_ring', 'msg_tx_ring'.  Now, I changed them to mport's
private members.  And you can define multi RIO OF-nodes in dts file for multi
RapidIO controller in one processor, such as PCI/PCI-Ex host controllers in
Freescale's silicon.  And the mport operation function declaration should be
changed to know which RapidIO controller is target.
Signed-off-by: NZhang Wei <wei.zhang@freescale.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Signed-off-by: NZhang Wei <wei.zhang@freescale.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Signed-off-by: NZhang Wei <wei.zhang@freescale.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

The driver is suitable for the Freescale MPC8641 processor as well as
85xx processors, so this changes the mpc85xx prefix to fsl.
Signed-off-by: NZhang Wei <wei.zhang@freescale.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Provide walk_memory_resource() for 64-bit powerpc.  PowerPC maintains
logical memory region mapping in the lmb.memory structure.  Walk
through these structures and do the callbacks for the contiguous
chunks.
Signed-off-by: NBadari Pulavarty <pbadari@us.ibm.com>
Cc: Yasunori Goto <y-goto@jp.fujitsu.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

The powerpc kernel maintains information about logical memory blocks
in the lmb.memory structure, which is initialized and updated at boot
time, but not when memory is added or removed while the kernel is
running.

This adds a hotplug memory notifier which updates lmb.memory when
memory is added or removed.  This information is useful for eHEA
driver to find out the memory layout and holes.

NOTE: No special locking is needed for lmb_add() and lmb_remove().
Calls to these are serialized by caller. (pSeries_reconfig_chain).
Signed-off-by: NBadari Pulavarty <pbadari@us.ibm.com>
Cc: Yasunori Goto <y-goto@jp.fujitsu.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Hotplug memory remove notifier for 64-bit powerpc.  This gets invoked
by writing to /proc/ppc64/ofdt the string "remove_node " followed by
the firmware device tree pathname of the node that needs to be removed.

In response, this adjusts the sections and removes sysfs entries by
calling __remove_pages().  Then it calls arch-specific code to get rid
of the hardware MMU mappings for the section of memory.
Signed-off-by: NBadari Pulavarty <pbadari@us.ibm.com>
Reviewed-by: NMichael Ellerman <michael@ellerman.id.au>
Cc: Yasunori Goto <y-goto@jp.fujitsu.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This implements a new driver named windfarm_pm121, which drives the
fans on PowerMac 12,1 machines : iMac G5 iSight (rev C) 17" and
20".  It's based on the windfarm_pm81 driver from Benjamin
Herrenschmidt.

This includes fixes from David Woodhouse correcting the names of some
of the sensors.
Signed-off-by: NÉtienne Bersac <bersace@gmail.com>
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Kamalesh Babulal (kamalesh@linux.vnet.ibm.com) reports that CONFIG_NVRAM=m
is valid in terms of Kconfig but fails to build with:
  Building modules, stage 2.
  MODPOST 1401 modules
ERROR: "pmac_newworld" [arch/powerpc/platforms/powermac/nvram.ko] undefined!
ERROR: "__alloc_bootmem" [arch/powerpc/platforms/powermac/nvram.ko] undefined!
make[1]: *** [__modpost] Error

The arch/powerpc/platforms/powermac/nvram.c code really needs to be
builtin, but as its compilation is dependent on a generic Kconfig
symbol we force nvram.c to be builtin if CONFIG_NVRAM is 'y' or 'm'.
Signed-off-by: NTony Breeds <tony@bakeyournoodle.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This makes it possible to use separate stacks for hard and soft IRQs
on 32-bit powerpc as well as on 64-bit.  The code for 32-bit is just
the 32-bit analog of the 64-bit code.

* Added allocation and initialization of the irq stacks.  We limit the
  stacks to be in lowmem for ppc32.
* Implemented ppc32 versions of call_do_softirq() and call_handle_irq()
  to switch the stack pointers
* Reworked how we do stack overflow detection.  We now keep around the
  limit of the stack in the thread_struct and compare against the limit
  to see if we've overflowed.  We can now use this on ppc64 if desired.

[ paulus@samba.org: Fixed bug on 6xx where we need to reload r9 with the
  thread_info pointer. ]
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This changes the definitions of the xchg and cmpxchg families of
functions in include/asm-powerpc/system.h to be marked __always_inline
rather than __inline__.  The reason for doing this is that we rely on
the compiler inlining them in order to eliminate the references to
__xchg_called_with_bad_pointer and __cmpxchg_called_with_bad_pointer,
which are deliberately left undefined.  Thus this change will enable
us to make the inline keyword be just a hint rather than a directive.
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This adds a system call on 64-bit platforms for switching between
little-endian and big-endian modes that is much faster than doing a
prctl call.  This system call is handled as a special case right at
the start of the system call entry code, and because it is a special
case, it uses a system call number which is out of the range of
normal system calls, namely 0x1ebe.

Measurements with lmbench on a 4.2GHz POWER6 showed no measurable
change in the speed of normal system calls with this patch.

Switching endianness with this new system call takes around 60ns on a
4.2GHz POWER6, compared with around 300ns to switch endian mode with a
prctl.  This can provide a significant performance advantage for
emulators for little-endian architectures that want to switch between
big-endian and little-endian mode frequently, e.g. because they are
generating instructions sequences on the fly and they want to run
those sequences in little-endian mode.

The other thing about this system call is that it doesn't clobber as
many registers as a normal system call.  It only clobbers r12.
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Signed-off-by: NHarvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

drivers/media/video/v4l2-common.c:719:16: warning: Using plain integer as NULL pointer
drivers/media/video/au0828/au0828-dvb.c:122:19: warning: Using plain integer as NULL pointer
drivers/media/video/ivtv/ivtv-yuv.c:1101:22: warning: Using plain integer as NULL pointer
drivers/media/video/ivtv/ivtv-yuv.c:1102:23: warning: Using plain integer as NULL pointer
drivers/media/video/pvrusb2/pvrusb2-audio.c:78:39: warning: Using plain integer as NULL pointer
drivers/media/video/pvrusb2/pvrusb2-video-v4l.c:84:39: warning: Using plain integer as NULL pointer
drivers/media/video/pvrusb2/pvrusb2-v4l2.c:1264:9: warning: Using plain integer as NULL pointer
drivers/media/video/pvrusb2/pvrusb2-context.c:197:28: warning: Using plain integer as NULL pointer
drivers/media/video/pvrusb2/pvrusb2-cx2584x-v4l.c:126:39: warning: Using plain integer as NULL pointer
drivers/media/video/pvrusb2/pvrusb2-dvb.c:133:32: warning: Using plain integer as NULL pointer
drivers/media/video/pvrusb2/pvrusb2-dvb.c:145:31: warning: Using plain integer as NULL pointer
drivers/media/video/pvrusb2/pvrusb2-dvb.c:177:55: warning: Using plain integer as NULL pointer
drivers/media/video/videobuf-core.c:100:9: warning: Using plain integer as NULL pointer
Signed-off-by: NHarvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

drivers/scsi/aic7xxx/aic7770_osm.c:53:58: warning: Using plain integer as NULL pointer
drivers/scsi/aic7xxx/aic7xxx_osm_pci.c:355:47: warning: Using plain integer as NULL pointer
drivers/scsi/aic7xxx/aic7xxx_osm_pci.c:372:55: warning: Using plain integer as NULL pointer
drivers/scsi/aha152x.c:997:28: warning: Using plain integer as NULL pointer
drivers/scsi/aha152x.c:1003:28: warning: Using plain integer as NULL pointer
drivers/scsi/aha152x.c:1165:46: warning: Using plain integer as NULL pointer
drivers/scsi/fdomain.c:1446:40: warning: Using plain integer as NULL pointer
drivers/scsi/sym53c8xx_2/sym_hipd.c:1650:51: warning: Using plain integer as NULL pointer
drivers/scsi/sym53c8xx_2/sym_hipd.c:3171:42: warning: Using plain integer as NULL pointer
drivers/scsi/sym53c8xx_2/sym_hipd.c:5732:52: warning: Using plain integer as NULL pointer
drivers/scsi/ncr53c8xx.c:8189:31: warning: Using plain integer as NULL pointer
drivers/scsi/ncr53c8xx.c:8225:34: warning: Using plain integer as NULL pointer
drivers/scsi/dpt_i2o.c:156:32: warning: Using plain integer as NULL pointer
drivers/scsi/ultrastor.c:954:42: warning: Using plain integer as NULL pointer
drivers/scsi/ultrastor.c:1104:18: warning: Using plain integer as NULL pointer
Signed-off-by: NHarvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6: (35 commits)
  siimage: coding style cleanup (take 2)
  ide-cd: clean up cdrom_analyze_sense_data()
  ide-cd: fix test unsigned var < 0
  ide: add TSSTcorp CDDVDW SH-S202H to ivb_list[]
  piix: add Asus Eee 701 controller to short cable list
  ARM: always select HAVE_IDE
  remove the broken ETRAX_IDE driver
  ide: remove ->dma_prdtable field from ide_hwif_t
  ide: remove ->dma_vendor{1,3} fields from ide_hwif_t
  scc_pata: add ->dma_host_set and ->dma_start methods
  ide: skip "VLB sync" if host uses MMIO
  ide: add ide_pad_transfer() helper
  ide: remove ->INW and ->OUTW methods
  ide: use IDE I/O helpers directly in ide_tf_{load,read}()
  ns87415: add ->tf_read method
  scc_pata: add ->tf_{load,read} methods
  ide-h8300: add ->tf_{load,read} methods
  ide-cris: add ->tf_{load,read} methods
  ide: add ->tf_load and ->tf_read methods
  ide: move ide_tf_{load,read} to ide-iops.c
  ...

* git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild:
  kconfig: add named choice group
  kconfig: fix choice dependency check
  kconifg: 'select' considered less evil
  dontdiff: ignore timeconst.h
  dontdiff: add modules.order
  kbuild: fix unportability in gen_initramfs_list.sh
  kbuild: fix help output to show correct arch
  kbuild: show defconfig subdirs in make help
  kconfig: reversed borderlines in inputbox

drivers/atm/nicstar.c:418:25: warning: Using plain integer as NULL pointer
drivers/char/drm/r128_cce.c:820:25: warning: Using plain integer as NULL pointer
drivers/char/tty_io.c:1183:10: warning: Using plain integer as NULL pointer
Signed-off-by: NHarvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

mm/hugetlb.c:207:11: warning: Using plain integer as NULL pointer
Signed-off-by: NHarvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

kernel/cpuset.c:1268:52: warning: Using plain integer as NULL pointer
kernel/pid_namespace.c:95:24: warning: Using plain integer as NULL pointer
Signed-off-by: NHarvey Harrison <harvey.harrison@gmail.com>
Reviewed-by: NPaul Jackson <pj@sgi.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

init/do_mounts_rd.c:215:13: warning: Using plain integer as NULL pointer
init/do_mounts_md.c:136:45: warning: Using plain integer as NULL pointer
Signed-off-by: NHarvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix 18 errors and several warnings given by checkpatch.pl:

- use of C99 // comments;

- trailing whitespace;

- 'switch' and 'case' not at the same indentation level;

- no space before the open parenthesis of the 'if' and 'switch' statements;

- space between function name and open parenthesis (though I have introduced
  such warnins in some places since the code looks prettier with the spaces);

- including <asm/io.h> instead of <linux/io.h>;

- line over 80 characters.

In addition to these changes, also do the following:

- make the arrays in sil_set_pio_mode() 'static', and make the arrays in
  sil_set_dma_mode() 'static const';

- change the string of the 'if' statements into the 'switch' statement in
  sil_pata_udma_filter();

- drop the needless '==' operators from the 'if' statements where a condition
  is a mere bit test;

- remove needless initializer for the 'tmp' variable in init_chipset_siimage();

- beautify groups of the variable initializers and assignment operators;

- add new line after variable definitions;

- remove new line between the comment and the statements it refers to;

- remove needless curly braces and parentheses;

- fix typos, capitalize acronyms, etc. in the comments...
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

[bart: fix handling of bio_sectors(failed_command->bio) == 0]
Signed-off-by: NRoel Kluin <12o3l@tiscali.nl>
Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

valid is unsigned and cannot be below 0.
Signed-off-by: NRoel Kluin <12o3l@tiscali.nl>
Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Based on ata_piix patch by Dan McGee.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

It's plain wrong for PCMCIA to select HAVE_IDE that implies e.g. the
availability of an asm/ide.h

It turns out this was done for ARM, and we can simply always select 
HAVE_IDE on ARM instead of manually tracking which platforms might 
possible have an IDE controller directly or indirectly.
Signed-off-by: NAdrian Bunk <bunk@kernel.org>
Cc: Russell King <rmk+lkml@arm.linux.org.uk>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>