Add geneve Rx offload support for x550em_a.

The implementation follows the vxlan code with the lower 16 bits of
the VXLANCTRL register holding the UDP port for VXLAN and the upper
for Geneve.

Disabled NFS filters in the RFCTL register which allows us to simplify
the check for VXLAN and Geneve packets in ixgbe_rx_checksum().

Removed vxlan from the name of the callback functions and replaced it
with udp_tunnel which is more in line with the new API.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The PF driver was only receiving the first 4 bytes of the MAC due
to an incorrect size parameter for ixgbevf_write_msg_read_ack()
in ixgbevf_set_rar_vf().

Correct the size by calculating it on a fly for all instances where
we call ixgbevf_write_msg_read_ack()
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

ethtool reports backplane type interfaces as 1000/10000baseT link modes.
This has been corrected to report the media as KR, KX or KX4 based on the backplane interface present.
Signed-off-by: NVeola Nazareth <veola.nazareth@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

RDMA client is closed during the PF reset and needs to be opened again.
Setting the flag so that RDMA client is opened in watchdog() function.

Change-ID: I507b1e4cbd05528cdff68fd360ef3dcac8901263
Signed-off-by: NAvinash Dayanand <avinash.dayanand@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Several defines and code comments were indented with spaces instead
of tabs, correct the issue to make indentation consistent.

Change-ID: I0dc6bbb990ec4a9e856acc9ec526d876181f092c
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>

Correcting the mutex usage, in client_subtask(), mutex_unlock has
to be called just before client_del_instance() since this function opens
and later closes the same mutex again.
Similarly in client_is_registered removing the mutex since it closes
the mutex twice.

This is a patch suggested by RDMA team.

Change-ID: Icce519c266e4221b8a2a72a15ba5bf01750e5852
Signed-off-by: NAvinash Dayanand <avinash.dayanand@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Use __stringify instead.
Signed-off-by: NJoe Perches <joe@perches.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The function i40e_client_release has a print statement that uses an
adapter pointer which is not initialized if a previous if statement
is not true. Hence, intialize it in the right place.

Change-ID: I1afdaa2c46771ac42be56edcc41bb56b455b06c8
Signed-off-by: NHarshitha Ramamurthy <harshitha.ramamurthy@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

We were having a race between the completion of the client open and
calls to the client ops so don't call a client op unless we are sure the
client is open.

Testing Hints: Load IWARP driver and make sure it works as expected.

Change-Id: I741f4f2aa4fcbfdad3e40dabbbb1b005856c396b
Signed-off-by: NCatherine Sullivan <catherine.sullivan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

i is defined as int but output as %u several times.
Adjust the format identifiers.
Signed-off-by: NHeinrich Schuchardt <xypron.glpk@gmx.de>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds support for HMC resource and profile cmds for X722
firmware.

Change-ID: Icc332101f38ab15d1bfa167823100eb4f6822f7e
Signed-off-by: NCarolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch fixes byte ordering problems found when enabling this feature
support. Without this patch, the feature will not work correctly. This
patch fixes the definitions to have the correct byte order.

Change-ID: Ic7489fbcbe2195df7be62ff5e359201b827cefe6
Signed-off-by: NCarolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch refactors tail bump check.

Change-ID: Ide0e19171d67d90cb2b06b8dcd4fa791ae120160
Signed-off-by: NCarolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The PF driver tells us the link speed, so do something with that
information. Add link speed to log messages, and report speed through
ethtool.

Change-Id: I279dc9540cc5203376406050a3e8d67e128d5882
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Replace calls to create_singlethread_workqueue instead with alloc_workqueue
as is style with other Intel drivers. This provides more control over
workqueue creation, and allows explicit setting of the desired mode of
operation. It also makes it more obvious that driver name constant is
passed to a format "%s".

Change-ID: I6192b44caf5140336cd54c5b350d51c73b541fdb
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

A previous refactor added support to store user configuration for VSIs,
so that extra VSIs such as for VMDq can use this information when
configuring. Unfortunately the i40e_vsi_config_rss function was missed
in this refactor, and the values were being ignored. Fix this by
checking for the fields and using those instead of always using the
default values.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

X722 hardware requires using the admin queue to configure RSS. This
function was previously re-written in commit e69ff813 ("i40e: rework
the functions to configure RSS with similar parameters").
However, the previous refactor did not work correctly for a few reasons

(a) it does not check whether seed is NULL before using it, resulting in
a NULL pointer dereference

[  402.954721] BUG: unable to handle kernel NULL pointer dereference at           (null)
[  402.955568] IP: [<ffffffffa0090ccf>] i40e_config_rss_aq.constprop.65+0x2f/0x1c0 [i40e]
[  402.956402] PGD ad610067 PUD accc0067 PMD 0
[  402.957235] Oops: 0000 [#1] SMP
[  402.958064] Modules linked in: ip6t_rpfilter ip6t_REJECT nf_reject_ipv6 xt_conntrack ip_set nfnetlink ebtable_filter ebtable_
broute bridge stp llc ebtable_nat ebtables ip6table_mangle ip6table_raw ip6table_nat nf_conntrack_ipv6 nf_defrag_ipv6 nf_nat_ipv
6 ip6table_security ip6table_filter ip6_tables iptable_mangle iptable_raw iptable_nat nf_conntrack_ipv4_ nf_defrag_ipv4_ nf_nat_ip
v4_ nf_nat nf_conntrack iptable_security intel_rapl i86_kg_temp_thermal coretemp kvm_intel kvm irqbypass crct10dif_clMl crc32_
pclMl ghash_clMlni_intel iTCO_wdt iTCO_vendor_support shpchp sb_edac dcdbas pcspkr joydev ipmi_devintf wmi edac_core ipmi_ssif
 acpi_ad acpi_ower_meter ipmi_si ipmi_msghandler mei_me nfsd lpc_ich mei ioatdma tpm_tis auth_rpcgss tpm nfs_acl lockd grace s
unrpc ifs nngag200 i2c_algo_bit drm_kms_helper ttm drm iigbe bnx2x i40e dca mdio ptp pps_core libcrc32c fjes crc32c_intel
[  402.965563] CPU: 22 PID: 2461 Conm: ethtool Not tainted 4.6.0-rc7_1.2-ABNidQ+ #20
[  402.966719] Hardware name: Dell Inc. PowerEdge R720/0C4Y3R, BIOS 2.5.2 01/28/2015
[  402.967862] task: ffff880219b51dc0 ti: ffff8800b3408000 task.ti: ffff8800b3408000
[  402.969046] RIP: 0010:[<ffffffffa0090ccf>]  [<ffffffffa0090ccf>] i40e_config_rss_aq.constprop.65+0x2f/0x1c0 [i40e]
[  402.970339] RSP: 0018:ffff8800b340ba90  EFLAGS: 00010246
[  402.971616] RAX: 0000000000000000 RBX: ffff88042ec14000 RCX: 0000000000000200
[  402.972961] RDX: ffff880428eb9200 RSI: 0000000000000000 RDI: ffff88042ec14000
[  402.974312] RBP: ffff8800b340baf8 R08: ffff880237ada8f0 R09: ffff880428eb9200
[  402.975709] R10: ffff880428eb9200 R11: 0000000000000000 R12: ffff88042ec2e000
[  402.977104] R13: ffff88042ec2e000 R14: ffff88042ec14000 R15: ffff88022ea00800
[  402.978541] FS:  00007f84fd054700(0000) GS:ffff880237ac0000(0000) knlGS:0000000000000000
[  402.980003] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[  402.981508] CR2: 0000000000000000 CR3: 000000003289e000 CR4: 00000000000406e0
[  402.983028] Stack:
[  402.984578]  0000000002000200 0000000000000000 ffff88023ffeda68 ffff88023ffef000
[  402.986187]  0000000000000268 ffff8800b340bbf8 ffff88023ffedd80 0000000088ce4f1d
[  402.987844]  ffff88042ec14000 ffff88022ea00800 ffff88042ec2e000 ffff88042ec14000
[  402.989509] Call Trace:
[  402.991200]  [<ffffffffa009636f>] i40e_config_rss+0x11f/0x1c0 [i40e]
[  402.992924]  [<ffffffffa00a1ae0>] i40e_set_rifh+0ic0/0x130 [i40e]
[  402.994684]  [<ffffffff816d54b7>] ethtool_set_rifh+0x1f7/0x300
[  402.996446]  [<ffffffff8136d02b>] ? cred_has_capability+0io6b/0x100
[  402.998203]  [<ffffffff8136d102>] ? selinux_capable+0x12/0x20
[  402.999968]  [<ffffffff8136277b>] ? security_capable+0x4b/0x70
[  403.001707]  [<ffffffff816d6da3>] dev_ethtool+0x1423/0x2290
[  403.003461]  [<ffffffff816eab41>] dev_ioctl+0x191/0io630
[  403.005186]  [<ffffffff811cf80a>] ? lru_cache_add+0x3a/0i80
[  403.006942]  [<ffffffff817f2a8e>] ? _raw_spin_unlock+0ie/0x20
[  403.008691]  [<ffffffff816adb95>] sock_do_ioctl+0x45/0i50
[  403.010421]  [<ffffffff816ae229>] sock_ioctl+0x209/0x2d0
[  403.012173]  [<ffffffff81262194>] do_vfs_ioctl+0u4/0io6c0
[  403.013911]  [<ffffffff81262829>] SyS_ioctl+0x79/0x90
[  403.015710]  [<ffffffff817f2e72>] entry_SYSCALL_64_fastpath+0x1a/0u4
[  403.017500] Code: 90 55 48 89 e5 41 57 41 56 41 55 41 54 53 48 89 fb 48 83 ec 40 4c 8b a7 e0 05 00 00 65 48 8b 04 25 28 00 00 00 48 89 45 d0 31 c0 <48> 8b 06 41 0f b7 bc 24 f2 0f 00 00 48 89 45 9c 48 8b 46 08 48
[  403.021454] RIP  [<ffffffffa0090ccf>] i40e_config_rss_aq.constprop.65+0x2f/0x1c0 [i40e]
[  403.023395]  RSP <ffff8800b340ba90>
[  403.025271] CR2: 0000000000000000
[  403.027169] ---[ end trace 64561b528cf61cf0 ]---

(b) it does not even bother to use the passed in *lut parameter which
defines the requested lookup table. Instead it uses its own round robin
table.

Fix these issues by re-writing it to be similar to i40e_config_rss_reg
and i40e_get_rss_aq.

Fixes: e69ff813 ("i40e: rework the functions to configure RSS with similar parameters", 2015-10-21)
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Move this function below the two functions related to configuring RSS
via the admin queue. This helps co-locate the two functions, and made it
easier to spot a bug in the first i40e_config_rss_aq function as
compared to the i40e_get_rss_aq function.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This new firmware for the qed* adpaters fixes several issues:
 - Better blocking of malicious VFs.
 - After FLR, Tx-switching [internal routing] of packets might
   be incorrect.
 - Deletion of unicast MAC filters would sometime have side-effect
   of corrupting the MAC filters configred for a device.
It also contains fixes for future qed* drivers that *hopefully* would be
sent for review in the near future.

In addition, it would allow driver some new functionality, including:
 - Allowing PF/VF driver compaitibility with old drivers [running
   pre-8.10.5.0 firmware].
 - Better debug facilities.

This would also bump the qed* driver versions to 8.10.9.20.
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

An upcoming feature of IBM VNIC protocol is the ability to configure
redundant backing devices for a VNIC client. In case of a failure
on the current backing device, the driver will receive a signal
from the hypervisor indicating that a failover will occur. The driver
will then wait for a message from the backing device before
establishing a new connection.
Signed-off-by: NThomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It added reset function for RoCE driver. RoCE is a feature of hns.
In hip06 SoC, in RoCE reset process, it's needed to configure dsaf
channel reset, port and sl map info. Reset function of RoCE is
located in dsaf module, we only call it in RoCE driver when needed.

This patch is used to fix the conflict, please refer to this link:
  https://www.spinics.net/lists/linux-rdma/msg39114.htmlSigned-off-by: NWei Hu <xavier.huwei@huawei.com>
Signed-off-by: NNenglong Zhao <zhaonenglong@hisilicon.com>
Signed-off-by: NLijun Ou <oulijun@huawei.com>
Signed-off-by: NSheng Li <lisheng011@huawei.com>
Reviewed-by: NYisen Zhuang <yisen.zhuang@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NAtul Gupta <atul.gupta@chelsio.com>
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a new commmon infrastructure to allocate reosurces dynamically to
Upper layer driver's(ULD) when they register with cxgb4 driver and free
them during unregistering. All the queues and the interrupts for
them will be allocated during ULD probe only and freed during remove.
Signed-off-by: NAtul Gupta <atul.gupta@chelsio.com>
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It doesn't really change anything as BGMAC_CHIPCTL_1_IF_TYPE_RMII is
equal to 0. It make code a bit clener, so far when reading it one could
think we forgot to set a proper mode. It also keeps this mode code in
sync with other ones.
Signed-off-by: NRafał Miłecki <rafal@milecki.pl>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

BCM53573 is a new series of Broadcom's SoCs. It's based on ARM and can
be found in two packages (versions): BCM53573 and BCM47189. It shares
some code with the Northstar family, but also requires some new quirks.

First of all there can be up to 2 Ethernet cores on this SoC. If that is
the case, they are connected to two different switch ports allowing some
more complex/optimized setups. It seems the second unit doesn't come
fully configured and requires some IRQ quirk.

Other than that only the first core is connected to the PHY. For the
second one we have to register fixed PHY (similarly to the Northstar),
otherwise generic PHY driver would get some invalid info.

This has been successfully tested on Tenda AC9 (BCM47189B0).
Signed-off-by: NRafał Miłecki <rafal@milecki.pl>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

trivial fix to spelling mistake in dev_err message
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The division is already being done properly in efx_ef10_get_timer_config
which returns zero-on-success, unlike the old efx_ef10_get_sysclk_freq.

Fixes: d95e329a ("sfc: get timer configuration from adapter")
Signed-off-by: NEdward Cree <ecree@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

While '0xdead' and '0xbeef' are "great" values, we should
use the correct SPEED_* values instead.

Fixes: 054c67d1 ("qed*: Add support for ethtool link_ksettings callbacks")
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When moving into using ethtool's link_ksetting, qed started
supplying its own bitmask of speed/capabilities, but qede
is still checking for the SUPPORTED value to determine whether
it supports pause.

Fixes: 054c67d1 ("qed*: Add support for ethtool link_ksettings callbacks")
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use atomic bitwise operations when setting and checking reset
requests. This should help with possible races in the service task.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Following a write the VFTXDCTL.ENABLE bit is set only when the Tx queue
is actually enabled, which may not happen during the configure phase even
if we waited for it. Make this check debug only since this is causing
confusion with users who notice the warning in dmesg.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Instead of the home brewed macro make use of netdev_dbg same as
the ixgbe driver.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Following a write the TXDCTL.ENABLE bit is set only when the Tx queue
is actually enabled, which may not happen during the configure phase even
if we waited for it. Make this check debug only since this is causing
confusion with users who notice the warning in dmesg.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Use error "rmgr: Cannot insert RX class rule: Operation not supported" is
more meaningful than "rmgr: Cannot insert RX class rule: Unknown error 524"
Signed-off-by: NGangfeng Huang <gangfeng.huang@ni.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch is meant to allow for RX network flow classification to insert
and remove VLAN priority filter by ethtool

Example:
Add an VLAN priority filter:
$ ethtool -N eth0 flow-type ether vlan 0x6000 vlan-mask 0x1FFF action 2 loc 1

Show all filters:
$ ethtool -n eth0
4 RX rings available
Total 1 rules

Filter: 1
	Flow Type: Raw Ethernet
	Src MAC addr: 00:00:00:00:00:00 mask: FF:FF:FF:FF:FF:FF
	Dest MAC addr: 00:00:00:00:00:00 mask: FF:FF:FF:FF:FF:FF
	Ethertype: 0x0 mask: 0xFFFF
	VLAN EtherType: 0x0 mask: 0xffff
	VLAN: 0x6000 mask: 0x1fff
	User-defined: 0x0 mask: 0xffffffffffffffff
	Action: Direct to queue 2

Delete the filter by location:
$ ethtool -N delete 1
Signed-off-by: NRuhao Gao <ruhao.gao@ni.com>
Signed-off-by: NGangfeng Huang <gangfeng.huang@ni.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch is meant to allow for RX network flow classification to insert
and remove ethertype filter by ethtool

Example:
Add an ethertype filter:
$ ethtool -N eth0 flow-type ether proto 0x88F8 action 2

Show all filters:
$ ethtool -n eth0
4 RX rings available
Total 1 rules

Filter: 15
	Flow Type: Raw Ethernet
	Src MAC addr: 00:00:00:00:00:00 mask: FF:FF:FF:FF:FF:FF
	Dest MAC addr: 00:00:00:00:00:00 mask: FF:FF:FF:FF:FF:FF
	Ethertype: 0x88F8 mask: 0x0
	Action: Direct to queue 2

Delete the filter by location:
$ ethtool -N delete 15
Signed-off-by: NRuhao Gao <ruhao.gao@ni.com>
Signed-off-by: NGangfeng Huang <gangfeng.huang@ni.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch is meant to allow for RX network flow classification to insert
and remove Rx filter by ethtool. Ethtool interface has it's own rules
manager

Show all filters:
$ ethtool -n eth0
4 RX rings available
Total 2 rules
Signed-off-by: NRuhao Gao <ruhao.gao@ni.com>
Signed-off-by: NGangfeng Huang <gangfeng.huang@ni.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The patch adds driver support for sending the NCSI statistics to the
MFW. This is an asynchronous request from MFW. Upon receiving this, driver
populates the required data and send it to MFW.
Signed-off-by: NSudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NSudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The patch adds driver support for capturing stats ttl0_discard and
packet_too_big_discard in "ethtool -S" display.
Signed-off-by: NSudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>