Starting with commit <8947e396> ("Documentation: dt: mtd:
replace "nor-jedec" binding with "jedec, spi-nor"") we have
"jedec,spi-nor" binding indicating support for JEDEC identification.

Use it for all flashes that are supposed to support READ ID op
according to the datasheets.
Signed-off-by: NHou Zhiqiang <Zhiqiang.Hou@freescale.com>
Signed-off-by: NScott Wood <oss@buserror.net>

Signed-off-by: NZhao Qiang <qiang.zhao@nxp.com>
Signed-off-by: NScott Wood <oss@buserror.net>

This patch adds pcsphy node to FManV3 device tree.
Signed-off-by: NIgal Liberman <igal.liberman@freescale.com>
Signed-off-by: NScott Wood <oss@buserror.net>

Describe the PHY topology for all configurations supported by each board

Based on prior work by Andy Fleming <afleming@freescale.com>
Signed-off-by: NShruti Kanetkar <Shruti@freescale.com>
Signed-off-by: NEmil Medve <Emilian.Medve@Freescale.com>
Signed-off-by: NIgal Liberman <Igal.Liberman@freescale.com>
Signed-off-by: NScott Wood <oss@buserror.net>

Signed-off-by: NAlessio Igor Bogani <alessio.bogani@elettra.eu>
Signed-off-by: NScott Wood <oss@buserror.net>

Avoid duplication of the interrupt-parent, migrate to 4 interrupt-cells
and set the right clock-frequency for pcie (100 Mhz).
Signed-off-by: NAlessio Igor Bogani <alessio.bogani@elettra.eu>
Signed-off-by: NScott Wood <oss@buserror.net>

Signed-off-by: NAlessio Igor Bogani <alessio.bogani@elettra.eu>
Signed-off-by: NScott Wood <oss@buserror.net>

add the missing RAID Engine device node for p5040.
otherwise, the device can not be detected.
Signed-off-by: NXuelin Shi <xuelin.shi@nxp.com>
Signed-off-by: NScott Wood <oss@buserror.net>

Signed-off-by: NAdam Buchbinder <adam.buchbinder@gmail.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Also add nodes and properties for thermal management support. Meanwhile
preprocessor support is needed using thermal of framework.
Signed-off-by: NJia Hongtao <hongtao.jia@freescale.com>
Reviewed-by: NScott Wood <scottwood@freescale.com>
Signed-off-by: NScott Wood <scottwood@freescale.com>

Also add nodes and properties for thermal management support. Meanwhile
preprocessor support is needed using thermal of framework.
Signed-off-by: NJia Hongtao <hongtao.jia@freescale.com>
Reviewed-by: NScott Wood <scottwood@freescale.com>
Signed-off-by: NScott Wood <scottwood@freescale.com>

p1010rdb uses the irq[4:5] for inta and intb to pcie,
it is active-high, so set it.
Signed-off-by: NZhao Qiang <qiang.zhao@freescale.com>
Signed-off-by: NScott Wood <scottwood@freescale.com>

FMan V3H has 2 different MURAM sizes:
    In B4860/4420 the MURAM size is 512KB.
    In T4240 and T2080 the MURAM size is 384KB.

The MURAM size in FMan V3H device tree is 384KB.
This patch updates the MURAM size for B4 to 512KB.
Signed-off-by: NIgal Liberman <igal.liberman@freescale.com>
Signed-off-by: NScott Wood <scottwood@freescale.com>

Signed-off-by: NHarninder Rai <harninder.rai@freescale.com>
Signed-off-by: NMinghuan Lian <Minghuan.Lian@freescale.com>
Signed-off-by: NHou Zhiqiang <B48286@freescale.com>
Signed-off-by: NScott Wood <scottwood@freescale.com>

All users of QPACE have upgraded to QPACE2 so remove the Cell QPACE code.
Signed-off-by: NRashmica Gupta <rashmicy@gmail.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

This file was originally cloned off of the MPC8641D-HPCN reference
platform, which actually had a PHY IRQ line connected. However this
board does not. The bogus entry was largely inert and went undetected
until commit 321beec5 ("net: phy: Use
interrupts when available in NOLINK state") was added to the tree.

With the above commit, the board fails to NFS boot since it sits waiting
for a PHY IRQ event that of course never arrives. Removing the bogus
entries from the DTS file fixes the issue.

Cc: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

if the language is not english objdump output is not parsed correctly
and format is "". Later, "ld -m $format" fails.

This patch adds "LANG=C" to force english output for objdump.
Signed-off-by: NLaurent Vivier <laurent@vivier.eu>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Based on prior work by Andy Fleming <afleming@freescale.com>
Signed-off-by: NShruti Kanetkar <Shruti@freescale.com>
Signed-off-by: NEmil Medve <Emilian.Medve@Freescale.com>
Signed-off-by: NIgal Liberman <Igal.Liberman@freescale.com>
Signed-off-by: NScott Wood <scottwood@freescale.com>

Based on prior work by Andy Fleming <afleming@freescale.com>
Signed-off-by: NShruti Kanetkar <Shruti@freescale.com>
Signed-off-by: NEmil Medve <Emilian.Medve@Freescale.com>
Signed-off-by: NIgal Liberman <Igal.Liberman@freescale.com>
Signed-off-by: NScott Wood <scottwood@freescale.com>

This allows new-style clock references to be used, which is needed for
fman.  The old clock nodes will be removed and all clock references
converted to new-style once the qoriq-cpufreq driver is updated to stop
depending on the old-style references in cpu nodes.
Signed-off-by: NScott Wood <scottwood@freescale.com>

Add a device tree binding for Freescale MPC512x LocalPlus Bus FIFO and
introduce the document describing that binding.
Signed-off-by: NAlexander Popov <alex.popov@linux.com>
Signed-off-by: NAnatolij Gustschin <agust@denx.de>

Add a boot wrapper script function run_cmd which will run a shell command
quietly and only print the output if either V=1 or an error occurs.

Also, run the ps3 dd commands with run_cmd to clean up the build output.
Signed-off-by: NGeoff Levand <geoff@infradead.org>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

To make provision for more than one L2 caches in the system, change the
name from L2 to L2_1; same as in T4 platforms.
* Also remove the L2 entry from common file
  "arch/powerpc/boot/dts/fsl/b4si-post.dtsi"
  Keep them only in separate files for b4860 and b4420.
Signed-off-by: NShaveta Leekha <shaveta@freescale.com>
Signed-off-by: NPoonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: NScott Wood <scottwood@freescale.com>

It makes no sense that some Freescale device tree files are in fsl
directory while some others not. This patch move Freescale device tree
files into fsl folder. To do that the following two steps are made:
- Move Freescale device tree files into fsl folder.
- Update the include path in these files from "fsl/*.dtsi" to "*.dtsi".

Please add "fsl/" prefix when you make dtb using Makefile.
Signed-off-by: NJia Hongtao <hongtao.jia@freescale.com>
[scottwood: fixed cuImage rule]
Signed-off-by: NScott Wood <scottwood@freescale.com>

In case of B4860 LIODN register for sRIO is not in GUTs block but in
the sRIO register space.
Signed-off-by: NVarun Sethi <Varun.Sethi@freescale.com>
Signed-off-by: NPoonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: NScott Wood <scottwood@freescale.com>

This board uses a P5020 chip, and boots just fine using
the corenet_generic code. The device tree is very similar to the
P5020DS, except that there is no Flash memory. The environment is,
instead, stored on an MMC card on the motherboard.
Signed-off-by: NAndy Fleming <afleming@gmail.com>
[scottwood: fixed trailing whitespace]
Signed-off-by: NScott Wood <scottwood@freescale.com>

DS26522 is used for tdm, configured by SPI bus.
Add nodes under spi node to t104xd4rdb.dtsi.
Signed-off-by: NZhao Qiang <qiang.zhao@freescale.com>
Signed-off-by: NScott Wood <scottwood@freescale.com>

While the handling of fsl,pq3-gpio and fsl,mpc8572-gpio is done in the
same driver and the two hardly differ, the latter controller needs a
workaround for an erratum in the gpio_get callback. To make this
difference more explicit remove fsl,pq3-gpio from the list of
compatibles for mpc8572 machines.
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NScott Wood <scottwood@freescale.com>

Add 1588 timer node in files:
arch/powerpc/boot/dts/bsc9131rdb.dtsi
arch/powerpc/boot/dts/bsc9132qds.dtsi
arch/powerpc/boot/dts/p1010rdb.dtsi
arch/powerpc/boot/dts/p1020rdb-pd.dts
arch/powerpc/boot/dts/p1021rdb-pc.dtsi
arch/powerpc/boot/dts/p1022ds.dtsi
arch/powerpc/boot/dts/p1025twr.dtsi
For P2020RDB-PC, registers' values should be calculated
based on default 1588 reference clock(300MHz) not 250MHz,
and fix this in file:
arch/powerpc/boot/dts/p2020rdb-pc.dtsi
Signed-off-by: NYangbo Lu <yangbo.lu@freescale.com>
Signed-off-by: NScott Wood <scottwood@freescale.com>

In commit 3c8464a9 ("powerpc:
Delete old PrPMC 280/2800 support") we got rid of most of the C
code, and the Makefile/Kconfig hooks, but it seems I left the
platform's DTS file orphaned in the tree as well as the boot code.
Here we get rid of them both.

Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

This avoid errors like

        unsigned int usize = 1 << 30;
        int size = 1 << 30;
        unsigned long addr = 64UL << 30 ;

        value = _ALIGN_DOWN(addr, usize); -> 0
        value = _ALIGN_DOWN(addr, size);  -> 0x1000000000
Signed-off-by: NAneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Enable the "wake-on-filer" (aka. wake on user defined packet)
wake on lan capability for the eTSEC ethernet nodes.

Cc: Li Yang <leoli@freescale.com>
Cc: Zhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: NClaudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The kernel does it, not the boot wrapper, which breaks with some
cross compilers that still default to ABI v1.

Fixes: 147c0516 ("powerpc/boot: Add support for 64bit little endian wrapper")
Cc: stable@vger.kernel.org # v3.16+
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

IFC NAND chip select is wrongly mapped to 2 in reg property of
NAND node. Due to this kernel is not able probe NAND flash. Set
chip select to 1 in reg property.
Signed-off-by: NJaiprakash Singh <b44839@freescale.com>
Signed-off-by: NShengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: NScott Wood <scottwood@freescale.com>

Signed-off-by: NWang Dongsheng <dongsheng.wang@freescale.com>
Signed-off-by: NScott Wood <scottwood@freescale.com>

T1040D4RDB/T1042D4RDB are Freescale Reference Design Board
which can support T1040/T1042 QorIQ Power
Architecture™ processor respectively

T1040D4RDB/T1042D4RDB board Overview
-------------------------------------
- SERDES Connections, 8 lanes supporting:
        - PCI
        - SGMII
        - SATA 2.0
        - QSGMII(only for T1040D4RDB)
    - DDR Controller
        - Supports rates of up to 1600 MHz data-rate
        - Supports one DDR4 UDIMM
    -IFC/Local Bus
        - NAND flash: 1GB 8-bit NAND flash
        - NOR: 128MB 16-bit NOR Flash
    - Ethernet
        - Two on-board RGMII 10/100/1G ethernet ports.
        - PHY #0 remains powered up during deep-sleep
    - CPLD
    - Clocks
        - System and DDR clock (SYSCLK, “DDRCLK”)
        - SERDES clocks
    - Power Supplies
    - USB
        - Supports two USB 2.0 ports with integrated PHYs
        - Two type A ports with 5V@1.5A per port.
    - SDHC
        - SDHC/SDXC connector
    - SPI
        - On-board 64MB SPI flash
    - I2C
        - Devices connected: EEPROM, thermal monitor, VID controller
    - Other IO
        - Two Serial ports
        - ProfiBus port

    Add support for T1040/T1042D4RDB board:
    -add device tree
    -Add entry in corenet_generic.c
Signed-off-by: NPriyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: NScott Wood <scottwood@freescale.com>

In u-boot, when set the video as console, the name 'vga' is used
as a general name for the video device, during the fdt_fixup_stdout
process, the 'vga' name is used to search in the dtb to setup the
'linux,stdout-path' node. Though the P1022 DIU is not VGA-compatible
device, to meet the 'vga' name used in u-boot, the vga alias node is
added for P1022 in this patch. At the same time, a display alias is
also added so that no other components grow dependencies on the vga
alias node.
Signed-off-by: NJason Jin <Jason.Jin@freescale.com>
Signed-off-by: NWang Dongsheng <dongsheng.wang@freescale.com>
Signed-off-by: NScott Wood <scottwood@freescale.com>

Add support for INA220 current sensor.
Signed-off-by: NShengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: NScott Wood <scottwood@freescale.com>

Add support for INA220 current sensor.
Signed-off-by: NShengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: NScott Wood <scottwood@freescale.com>

Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
Signed-off-by: NGeoff Thorpe <Geoff.Thorpe@freescale.com>
Signed-off-by: NHai-Ying Wang <Haiying.Wang@freescale.com>
Signed-off-by: NChunhe Lan <Chunhe.Lan@freescale.com>
Signed-off-by: NPoonam Aggrwal <poonam.aggrwal@freescale.com>
[Emil Medve: Sync with the upstream binding]
Signed-off-by: NEmil Medve <Emilian.Medve@Freescale.com>
[Scott Wood: s/fsl,qman-channel-id/cell-index]
Signed-off-by: NScott Wood <scottwood@freescale.com>
Cc: Madalin-Cristian Bucur <madalin.bucur@freescale.com>