powerpc/fsl-booke: Add T1040D4RDB/T1042D4RDB board support

T1040D4RDB/T1042D4RDB are Freescale Reference Design Board
which can support T1040/T1042 QorIQ Power
Architecture™ processor respectively

T1040D4RDB/T1042D4RDB board Overview
-------------------------------------
- SERDES Connections, 8 lanes supporting:
        - PCI
        - SGMII
        - SATA 2.0
        - QSGMII(only for T1040D4RDB)
    - DDR Controller
        - Supports rates of up to 1600 MHz data-rate
        - Supports one DDR4 UDIMM
    -IFC/Local Bus
        - NAND flash: 1GB 8-bit NAND flash
        - NOR: 128MB 16-bit NOR Flash
    - Ethernet
        - Two on-board RGMII 10/100/1G ethernet ports.
        - PHY #0 remains powered up during deep-sleep
    - CPLD
    - Clocks
        - System and DDR clock (SYSCLK, “DDRCLK”)
        - SERDES clocks
    - Power Supplies
    - USB
        - Supports two USB 2.0 ports with integrated PHYs
        - Two type A ports with 5V@1.5A per port.
    - SDHC
        - SDHC/SDXC connector
    - SPI
        - On-board 64MB SPI flash
    - I2C
        - Devices connected: EEPROM, thermal monitor, VID controller
    - Other IO
        - Two Serial ports
        - ProfiBus port

    Add support for T1040/T1042D4RDB board:
    -add device tree
    -Add entry in corenet_generic.c
Signed-off-by: NPriyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: NScott Wood <scottwood@freescale.com>

arch/powerpc/boot/dts/t1040d4rdb.dts

+/*
+ * T1040D4RDB Device Tree Source
+ *
+ * Copyright 2015 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ *     * Redistributions of source code must retain the above copyright
+ *	 notice, this list of conditions and the following disclaimer.
+ *     * Redistributions in binary form must reproduce the above copyright
+ *	 notice, this list of conditions and the following disclaimer in the
+ *	 documentation and/or other materials provided with the distribution.
+ *     * Neither the name of Freescale Semiconductor nor the
+ *	 names of its contributors may be used to endorse or promote products
+ *	 derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor "AS IS" AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+/include/ "fsl/t104xsi-pre.dtsi"
+/include/ "t104xd4rdb.dtsi"
+
+/ {
+	model = "fsl,T1040D4RDB";
+	compatible = "fsl,T1040D4RDB";
+	#address-cells = <2>;
+	#size-cells = <2>;
+	interrupt-parent = <&mpic>;
+};
+
+/include/ "fsl/t1040si-post.dtsi"

arch/powerpc/boot/dts/t1042d4rdb.dts

+/*
+ * T1042D4RDB Device Tree Source
+ *
+ * Copyright 2015 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ *     * Redistributions of source code must retain the above copyright
+ *	 notice, this list of conditions and the following disclaimer.
+ *     * Redistributions in binary form must reproduce the above copyright
+ *	 notice, this list of conditions and the following disclaimer in the
+ *	 documentation and/or other materials provided with the distribution.
+ *     * Neither the name of Freescale Semiconductor nor the
+ *	 names of its contributors may be used to endorse or promote products
+ *	 derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor "AS IS" AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+/include/ "fsl/t104xsi-pre.dtsi"
+/include/ "t104xd4rdb.dtsi"
+
+/ {
+	model = "fsl,T1042D4RDB";
+	compatible = "fsl,T1042D4RDB";
+	#address-cells = <2>;
+	#size-cells = <2>;
+	interrupt-parent = <&mpic>;
+
+	ifc: localbus@ffe124000 {
+		cpld@3,0 {
+			compatible = "fsl,t1040d4rdb-cpld",
+					"fsl,deepsleep-cpld";
+		};
+	};
+};
+
+/include/ "fsl/t1040si-post.dtsi"

arch/powerpc/boot/dts/t104xd4rdb.dtsi

+/*
+ * T1040D4RDB/T1042D4RDB Device Tree Source
+ *
+ * Copyright 2015 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ *     * Redistributions of source code must retain the above copyright
+ *	 notice, this list of conditions and the following disclaimer.
+ *     * Redistributions in binary form must reproduce the above copyright
+ *	 notice, this list of conditions and the following disclaimer in the
+ *	 documentation and/or other materials provided with the distribution.
+ *     * Neither the name of Freescale Semiconductor nor the
+ *	 names of its contributors may be used to endorse or promote products
+ *	 derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor "AS IS" AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+/ {
+	reserved-memory {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		bman_fbpr: bman-fbpr {
+			size = <0 0x1000000>;
+			alignment = <0 0x1000000>;
+		};
+		qman_fqd: qman-fqd {
+			size = <0 0x400000>;
+			alignment = <0 0x400000>;
+		};
+		qman_pfdr: qman-pfdr {
+			size = <0 0x2000000>;
+			alignment = <0 0x2000000>;
+		};
+	};
+
+	ifc: localbus@ffe124000 {
+		reg = <0xf 0xfe124000 0 0x2000>;
+		ranges = <0 0 0xf 0xe8000000 0x08000000
+			  2 0 0xf 0xff800000 0x00010000
+			  3 0 0xf 0xffdf0000 0x00008000>;
+
+		nor@0,0 {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			compatible = "cfi-flash";
+			reg = <0x0 0x0 0x8000000>;
+			bank-width = <2>;
+			device-width = <1>;
+		};
+
+		nand@2,0 {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			compatible = "fsl,ifc-nand";
+			reg = <0x2 0x0 0x10000>;
+		};
+
+		cpld@3,0 {
+			compatible = "fsl,t1040d4rdb-cpld";
+			reg = <3 0 0x300>;
+		};
+	};
+
+	memory {
+		device_type = "memory";
+	};
+
+	dcsr: dcsr@f00000000 {
+		ranges = <0x00000000 0xf 0x00000000 0x01072000>;
+	};
+
+	bportals: bman-portals@ff4000000 {
+		ranges = <0x0 0xf 0xf4000000 0x2000000>;
+	};
+
+	qportals: qman-portals@ff6000000 {
+		ranges = <0x0 0xf 0xf6000000 0x2000000>;
+	};
+
+	soc: soc@ffe000000 {
+		ranges = <0x00000000 0xf 0xfe000000 0x1000000>;
+		reg = <0xf 0xfe000000 0 0x00001000>;
+
+		spi@110000 {
+			flash@0 {
+				#address-cells = <1>;
+				#size-cells = <1>;
+				compatible = "micron,n25q512ax3";
+				reg = <0>;
+				/* input clock */
+				spi-max-frequency = <10000000>;
+			};
+		};
+		i2c@118000 {
+			hwmon@4c {
+				compatible = "adi,adt7461";
+				reg = <0x4c>;
+			};
+
+			rtc@68 {
+				compatible = "dallas,ds1337";
+				reg = <0x68>;
+				interrupts = <0x2 0x1 0 0>;
+			};
+		};
+
+		i2c@118100 {
+			mux@77 {
+				/*
+				 * Child nodes of mux depend on which i2c
+				 * devices are connected via the mini PCI
+				 * connector slot1, the mini PCI connector
+				 * slot2, the HDMI connector, and the PEX
+				 * slot. Systems with such devices attached
+				 * should provide a wrapper .dts file that
+				 * includes this one, and adds those nodes
+				 */
+				compatible = "nxp,pca9546";
+				reg = <0x77>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+
+	};
+
+	pci0: pcie@ffe240000 {
+		reg = <0xf 0xfe240000 0 0x10000>;
+		ranges = <0x02000000 0 0xe0000000 0xc 0x0 0x0 0x10000000
+			  0x01000000 0 0x0 0xf 0xf8000000 0x0 0x00010000>;
+		pcie@0 {
+			ranges = <0x02000000 0 0xe0000000
+				  0x02000000 0 0xe0000000
+				  0 0x10000000
+
+				  0x01000000 0 0x00000000
+				  0x01000000 0 0x00000000
+				  0 0x00010000>;
+		};
+	};
+
+	pci1: pcie@ffe250000 {
+		reg = <0xf 0xfe250000 0 0x10000>;
+		ranges = <0x02000000 0 0xe0000000 0xc 0x10000000 0 0x10000000
+			  0x01000000 0 0 0xf 0xf8010000 0 0x00010000>;
+		pcie@0 {
+			ranges = <0x02000000 0 0xe0000000
+				  0x02000000 0 0xe0000000
+				  0 0x10000000
+
+				  0x01000000 0 0x00000000
+				  0x01000000 0 0x00000000
+				  0 0x00010000>;
+		};
+	};
+
+	pci2: pcie@ffe260000 {
+		reg = <0xf 0xfe260000 0 0x10000>;
+		ranges = <0x02000000 0 0xe0000000 0xc 0x20000000 0 0x10000000
+			  0x01000000 0 0x00000000 0xf 0xf8020000 0 0x00010000>;
+		pcie@0 {
+			ranges = <0x02000000 0 0xe0000000
+				  0x02000000 0 0xe0000000
+				  0 0x10000000
+
+				  0x01000000 0 0x00000000
+				  0x01000000 0 0x00000000
+				  0 0x00010000>;
+		};
+	};
+
+	pci3: pcie@ffe270000 {
+		reg = <0xf 0xfe270000 0 0x10000>;
+		ranges = <0x02000000 0 0xe0000000 0xc 0x30000000 0 0x10000000
+			  0x01000000 0 0x00000000 0xf 0xf8030000 0 0x00010000>;
+		pcie@0 {
+			ranges = <0x02000000 0 0xe0000000
+				  0x02000000 0 0xe0000000
+				  0 0x10000000
+
+				  0x01000000 0 0x00000000
+				  0x01000000 0 0x00000000
+				  0 0x00010000>;
+		};
+	};
+};

arch/powerpc/platforms/85xx/corenet_generic.c

@@ -153,6 +153,8 @@ static const char * const boards[] __initconst = {
 	"fsl,T1023RDB",
 	"fsl,T1024QDS",
 	"fsl,T1024RDB",
+	"fsl,T1040D4RDB",
+	"fsl,T1042D4RDB",
 	"fsl,T1040QDS",
 	"fsl,T1042QDS",
 	"fsl,T1040RDB",