Effectively removes one layer of indirection between the mask of
possible engines and the engine constructors. Instead of spelling
out in code the mapping of HAS_<engine> to constructors, makes
more use of the recently added data driven approach by putting
engine constructor vfuncs into the table as well.

Effect is fewer lines of source and smaller binary.

At the same time simplify the error handling since engine
destructors can run on unitialized engines anyway.

Similar approach could be done for legacy submission is wanted.

v2: Removed ugly BUILD_BUG_ONs in favour of newly introduced
    ENGINE_MASK and HAS_ENGINE macros.
    Also removed the forward declarations by shuffling functions
    around.

v3: Warn when logical_rings table does not contain enough data
    and disable the engines which could not be initialized.
    (Chris Wilson)

v4: Chris Wilson suggested a nicer engine init loop.
Signed-off-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1466689961-23232-1-git-send-email-tvrtko.ursulin@linux.intel.com

During hibernation the cached DP port register value will be left with
whatever value we have there when we create the hibernation image.
Currently that means the port (and eDP PLL) will be off in the cached
value. However when we resume there is no guarantee that the value
in the actual register will match the cached value. If i915 isn't
loaded in the kernel that loads the hibernation image, the port may
well be on (eg. left on by the BIOS). The encoder state readout
does the right thing in this case and updates our encoder state
to reflect the actual hardware state. However the post-resume modeset
will then use the stale cached port register value in
intel_dp_link_down() and potentially confuse the hardware.

This was caught by the following assert
 WARNING: CPU: 3 PID: 5288 at ../drivers/gpu/drm/i915/intel_dp.c:2184 assert_edp_pll+0x99/0xa0 [i915]
 eDP PLL state assertion failure (expected on, current off)
on account of the eDP PLL getting prematurely turned off when
shutting down the port, since the DP_PLL_ENABLE bit wasn't set
in the cached register value.

Presumably I introduced this problem in
commit 6fec7662 ("drm/i915: Use intel_dp->DP in eDP PLL setup")
as before that we didn't update the cached value after shuttting the
port down. That's assuming the port got enabled at least once prior
to hibernating. If that didn't happen then the cached value would
still have been totally out of sync with reality (eg. first boot w/o
eDP on, then hibernate, and then resume with eDP on).

So, let's fix this properly and refresh the cached register value from
the hardware register during resume.

DDI platforms shouldn't use the cached value during port disable at
least, so shouldn't have this particular issue. They might still have
issues if we skip the initial modeset and then try to retrain the link
or something. But untangling this DP vs. DDI mess is a bigger topic,
so let's jut punt on DDI for now.

Cc: Jani Nikula <jani.nikula@intel.com>
Cc: stable@vger.kernel.org
Fixes: 6fec7662 ("drm/i915: Use intel_dp->DP in eDP PLL setup")
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463162036-27931-1-git-send-email-ville.syrjala@linux.intel.comReviewed-by: NImre Deak <imre.deak@intel.com>

The wait for panel status helper will only function correctly if the
HW panel timings are programmed correctly. Returning prematurely from
this helper may lead to obscure bugs later, so sanity check the HW
timing registers.

v2:
- Check the T8, T9 fields too, we do program them (Ville)

CC: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1466096506-11937-1-git-send-email-imre.deak@intel.com

This will be needed by the next patch too so factor it out.

No functional change.
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1466084243-5388-4-git-send-email-imre.deak@intel.com

No functional change.
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1466084243-5388-3-git-send-email-imre.deak@intel.com

The PPS registers are backed by power well #0 and as such may be reset
after system or runtime suspend (both implying a possible DC9
transition). Fix this by reusing the VLV/CHV PPS pipe-reassignment
logic. The difference on BXT is that the PPS instances are not pipe but
port (or more accurately pin) specific, so we only need to care about
the lost HW state. As opposed to VLV/CHV the SW state is fixed and
initialized during connector init.

This also paves the way towards using the actual port->PPS instance
mapping based on VBT.

This fixes eDP link training errors on BXT after suspend, where we
started the link training too early due to an incorrect T3 (panel power
on) register value.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=96436Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1466084243-5388-2-git-send-email-imre.deak@intel.com

Move the early PPS initialization calls next to the rest of PPS
initialization steps. This allows us to forgo a duplicated call to
intel_dp_init_panel_power_sequencer_registers() on VLV/CHV.

This will swap the order of DP AUX registration wrt. PPS initialization.
There is an existing race here in case of a user space access via the
DPAUX device node after DP AUX registration and before calling
intel_dp_init_panel_power_sequencer_registers(), but this change won't
make this worse. The fix for this is to separate DP AUX initialization
and registration, that's a separate work already underway.

The order of MST wrt. PPS init as well as the order of
intel_dp_init_panel_power_sequencer_registers() wrt.
intel_edp_panel_vdd_sanitize() also swap, which is ok, there are no
dependencies between these steps.

Suggested by Ville.

CC: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1466499109-20240-4-git-send-email-imre.deak@intel.com

The initial DPCD read for eDP detection involves using the PPS, but so
far we only initialized the PPS registers after the DPCD read. The
reason this was done so far is to preserve a possible LVDS PPS HW setup
if LVDS is detected but eDP is not. This is not an issue any more after
the previous patch, so we can move the init earlier now.

This was caught by CI with the PPS sanity checks in place and the
initial eDP DPCD readout waiting for the panel power cycle timeout
without the PPS registers being initialized.

CC: Ville Syrjälä <ville.syrjala@linux.intel.com>
CC: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1466499109-20240-3-git-send-email-imre.deak@intel.com

Atm on IBX/CPT we attempt to detect if eDP is present even if LVDS was
already detected and an encoder for it was registered. This involves
trying to read out the eDP DPCD, which in turn needs the same power
sequencer that LVDS uses. Poking at the VDD line at an unexpected time
may or may not interfere with the LVDS panel, but it's probably safer to
prevent this. Registering both an LVDS and an eDP connector would also
present a similar problem accessing the shared PPS at any point later in
an unexpected way.

We also need this to be able fix PPS initialization before its first use
in the next patch. For that we want to be sure that PPS is not in use
by LVDS.

v2:
- Split out the PPS init fix to a separate patch. (Chris)
- Add comment about eDP init depending on LVDS init. (Chris)
- Make the use of the intel_encoder ptr less error prone.
v3:
- Use IBX/CPT reference instead of the incorrect ILK, add a WARN about
  this. (Ville)
v4:
- Use a helper to get the lvds encoder instead of opencoding the same.
  (Ville)

CC: Ville Syrjälä <ville.syrjala@linux.intel.com>
CC: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> (v2)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> (v3)
Link: http://patchwork.freedesktop.org/patch/msgid/1466499109-20240-2-git-send-email-imre.deak@intel.com

Also extract drm_auth.h for nicer grouping.

v2: Nuke the other comments since they don't really explain a lot, and
within the drm core we generally only document functions exported to
drivers: The main audience for these docs are driver writers.

v3: Limit the exposure of drm_master internals by only including
drm_auth.h where it is neede (Chris).

v4: Spelling polish (Emil).

Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NEmil Velikov <emil.l.velikov@gmail.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@intel.com>

Just rolling out a bit of abstraction to be able to clean
up the master logic in the next step.

Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NEmil Velikov <emil.l.velikov@gmail.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

No need for local struct drm_device * since dev_priv is the
correct thing to pass in to NEEDS_WaRsDisableCoarsePowerGating
anyway. Changed the macro definition for the latter to reflect
that as well.

v2: Alignment bikeshed.
Signed-off-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Dave Gordon <david.s.gordon@intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1466518034-24838-1-git-send-email-tvrtko.ursulin@linux.intel.com

Instead of looking at encoder->type, which may be set to UNKNOWN,
use connector->connector_type. Info cannot be printed for MST
connectors which may have a NULL encoder, return early in that case.

Changes since v1:
- Whitelist encoder types for HDMI and LVDS.
- Fix oops on MST.
- Do not list encoder types for eDP/DP, they're always valid.
Signed-off-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/7cf34026-392d-01ec-e79b-e91919d1d783@linux.intel.com

DPMS is unreliable, use crtc->state.
Signed-off-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1466431059-8919-4-git-send-email-maarten.lankhorst@linux.intel.comReviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>

Signed-off-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1466431059-8919-3-git-send-email-maarten.lankhorst@linux.intel.comReviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>

This removes relying on intel_encoder->type, which may be set to
unknown.
Signed-off-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1466431059-8919-2-git-send-email-maarten.lankhorst@linux.intel.comReviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>

If we update the value of i915.enable_gvt should we fail to load GVT,
userspace can easily detect when it fails to load as requested.

Testcase: igt/gvt_basic
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Zhi Wang <zhi.a.wang@intel.com>
Reviewed-by: NZhi Wang <zhi.a.wang@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1466507234-23242-1-git-send-email-chris@chris-wilson.co.uk

The access right of kernel param "i915.enable_gvt" should be read-only as
it only applies during module load (and is not *runtime* writable).

Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NZhi Wang <zhi.a.wang@intel.com>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1466425022-3709-1-git-send-email-zhi.a.wang@intel.com

If the GPU load is low enough, it's possible that we'll be stuck at idle
frequency rather than transition into softmin frequency requested by
userspace.

v2: Use intel_set_rps, drop vlv_set_idle
v3: Back to vlv_set_idle, clamp to valid range
v4: Place intel_set_rps at the end

References: https://bugs.freedesktop.org/show_bug.cgi?id=89728
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NMichał Winiarski <michal.winiarski@intel.com>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1466416707-12075-1-git-send-email-michal.winiarski@intel.com

The ONLY places that guc_id (aka hw_id) should be used are those where
the value or address is determined by and shared with the GuC firmware;
specifically, when filling in the GuC-context-descriptor or the GuC
addon data, or putting an entry in the GuC's work queue.

It need not (and therefore should not) be used to index GuC statistics
or similar host-managed tracking data. In particular, i915_guc_submit()
produces (and debugfs decodes) GuC submission statistics which should be
indexed by driver-engine-id rather then guc-engine-id.
Signed-off-by: NDave Gordon <david.s.gordon@intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1466432287-5799-1-git-send-email-david.s.gordon@intel.com

During lastclose, we call intel_fbdev_restore_mode() to switch back to
the fbcon configuration on return to VT. However, if we have not yet
finished the asynchronous fbdev initialisation, the current mode will be
invalid and trigger WARNs upon application.

Serialise with the outstanding initialisation if the first application
exits quickly. Note that to hit this in practice requires using an
unregistered async_domain as otherwise modprobe will force a full
synchronisation prior to init() completing.

v2: Reuse comment explaining the +1 by refactoring the wait on fbdev
sync in the previous patch.
Reported-by: NGustav Fägerlind <gustav.fagerlind@gmail.com>
Reported-by: N"Li, Weinan Z" <weinan.z.li@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=93580Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1466497015-8509-3-git-send-email-chris@chris-wilson.co.uk

During cleanup we have to synchronise with the async task we are using
to initialise and register our fbdev. Currently, we are using a full
synchronisation on the global domain, but we can restrict this to just
synchronising up to our task if we remember our cookie.

Whilst there, streamline the function parameters.

v2: async_synchronize_cookie() takes an exclusive upper bound, to
synchronize with our task we have to pass in the next cookie.
v3: Drop premature disregarding of the active cookie (we need to wait
until the task is complete before continuing in the teardown).
v4: Refactor waiting on async to incorporate a comment explaining why we
need the +1.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1466497015-8509-2-git-send-email-chris@chris-wilson.co.uk

Setting up fbdev requires everything ready and registered (in particular
the connectors). In the forthcoming patches, we defer registration of the KMS
objects and unless we defer setting off fbdev, it may run before they are
registered and oops.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1466497015-8509-1-git-send-email-chris@chris-wilson.co.uk

... instead of the previous ORIGIN_GTT. This should actually
invalidate FBC once something is written on the frontbuffer using WC
mmaps. The problem with ORIGIN_GTT is that the automatic hardware
tracking is not able to detect the WC writes as it can detect the GTT
writes.

This should help fix the SKL bug where nothing happens when you type
your username/password on lightdm.

This patch was originally pasted on an email by Chris and converted to
an actual git patch by Paulo.

v2 (from Paulo):
 - Make it a full variable instead of a bit-field (Daniel)
 - Use WRITE_ONCE (Chris)
v3 (from Paulo):
 - Remove huge comment since now we have WRITE_ONCE (Chris)
 - Remove uneeded new line (Chris)
 - Add Chris' Signed-off-by, authorized via IRC

Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1466185599-26401-1-git-send-email-paulo.r.zanoni@intel.com

The DDX driver changes its behavior depending on the value it reads
from i915.enable_fbc, so sanitize the value in order to allow it to
know what's going on. It uses this in order to choose the defaults for
the TearFree option. Before this patch, it would read -1 and always
assume that FBC was disabled, so it wouldn't force TearFree.

v2: Extract intel_sanitize_fbc_option() (Chris).
v3: Rebase.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1460574069-14005-1-git-send-email-paulo.r.zanoni@intel.com

We ignore ORIGIN_GTT because the hardware tracking can recognize GTT
writes and take care of them. We also ignore ORIGIN_FLIP because we
deal with flips without relying on the frontbuffer tracking
infrastructure. On the other hand, a flush is a flush and means we're
good to go, so we need to update busy_bits in order to reflect that,
even if we're not going to do anything else about it.

How to reproduce the bug fixed by this patch:
 - boot SKL up to the desktop environment
 - stop the display manager
 - run any of the igt/kms_frontbuffer_tracking/*fbc*onoff* subtests
 - the tests will fail

The steps above will create the right conditions for us to lose track
of busy_bits. If you, for example, run the full set of FBC tests, the
onoff subtests will succeed.

Also notice that the "bug" is that we'll just keep FBC disabled on
cases where it could be enabled, so it's not something the users can
perceive, it just affects power consumption numbers on properly
configured machines.

Testcase: igt/kms_frontbuffer_tracking/*fbc*onoff* (see above)
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459804638-3588-2-git-send-email-paulo.r.zanoni@intel.com

>From https://bugs.freedesktop.org/show_bug.cgi?id=96461 :

This was kind of a difficult bug to track down. If you're using a
Haswell system running GNOME and you have fbc completely enabled and
working, playing videos can result in video artifacts. Steps to
reproduce:

- Run GNOME
- Ensure FBC is enabled and active
- Download a movie, I used the ogg version of Big Buck Bunny for this
- Run `gst-launch-1.0 filesrc location='some_movie.ogg' ! decodebin !
  glimagesink` in a terminal
- Watch for about over a minute, you'll see small horizontal lines go
  down the screen.

For the time being, disable FBC for Haswell by default.

Stefan Richter reported kernel freezes (no video artifacts) when fbc
is on.  (E3-1245 v3 with HD P4600; openbox and some KDE and LXDE
applications, thread begins at https://lkml.org/lkml/2016/4/26/813).
We also got reports from Steven Honeyman on openbox+roxterm.

v2 (From Paulo):
  - Add extra information to the commit message
  - Add Fixes tag
  - Rebase

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=96461
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=96464
Fixes: a98ee793 ("drm/i915/fbc: enable FBC by default on HSW and BDW")
Cc: stable@vger.kernel.org
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NLyude <cpaul@redhat.com>
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1465487895-7401-1-git-send-email-cpaul@redhat.com

The idea behind relaxing the restriction for pread/pwrite was to handle
!obj->base.flip, i.e. non-shmemfs backed objects, which only requires
that the object provide struct pages.

v2: Remove excess (). Note enough editing after copy'n'paste.
v3: Use new i915_gem_object_has_struct_page()

Testcase: igt/prime_vgem/read
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Ankitprasad Sharma <ankitprasad.r.sharma@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1466431552-17860-2-git-send-email-chris@chris-wilson.co.uk

Currently to see if an object is backed by struct pages (as opposed to
being a simple pointer to stolen memory, for example) we do a manual
check on the obj->ops->flags. This is quite shouty and before adding
more checks in future, we should make it a bit calmer.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1466431552-17860-1-git-send-email-chris@chris-wilson.co.uk

The drm_dp_aux is associated with the intel_dp encoder and not the
connector. Since the encoder is destroyed before the connector,
attempting to free the drm_dp_aux from inside the connector cleanup
causes a use-after-free.

This was applied to the patch that CI was happy with, but in the
confusion of so many series trying to make CI happy, the unready
patch was plucked.

Fixes: c191eca1 ("drm/i915: Move intel_connector->unregister to connector->early_unregister")
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1466411357-730-1-git-send-email-chris@chris-wilson.co.uk

It has been found out that in some HW combination the DisplayPort
fast link training feature caused screen flickering. Let's revert
this feature for now until we can ensure that the feature works for
all platforms.

This is a manual revert of commits 5fa836a9 ("drm/i915: DP link
training optimization") and 4e96c977 ("drm/i915: eDP link training
optimization").

Fixes: 5fa836a9 ("drm/i915: DP link training optimization")
Fixes: 4e96c977 ("drm/i915: eDP link training optimization")
Cc: <stable@vger.kernel.org> # v4.2+

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=91393Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NMika Kahola <mika.kahola@intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1466410226-19543-1-git-send-email-mika.kahola@intel.com

Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Currently the backlight is being unregistered in the unload phase (after
the display and its objects are unregistered). Move the backlight
unregistration into the analogous phase by performing it from the
connector unregistration, just prior to its deletion.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1466160034-12173-3-git-send-email-chris@chris-wilson.co.uk

We now have a connector->func that serves the same purpose as our own
intel_connector->unregister vfunc allowing us to unwrap ourselves and
use drm_connector_register() (and friends) as the central function.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1466160034-12173-2-git-send-email-chris@chris-wilson.co.uk

GVT workload scheduler needs special host LRC contexts, the so called
"shadow LRC context" to submit guest workload to host i915. During the
guest workload submission, workload scheduler fills the shadow LRC
context with the content of guest LRC context: engine context is copied
without changes, ring context is mostly owned by host i915.

v8:

- Remove the graph temporarily. (Chris)
- Use interruptible mutex_lock. (Chris)
- Rename the function name of creating a GVT context. (Chris)
- Add the missing declaration in i915_drv.h (Chris)

v7:

- Move chart to a better place. (Joonas)

v6:

- Make GVT code as dead code when !CONFIG_DRM_I915_GVT. (Chris)

v5:
- Only compile this feature when CONFIG_DRM_I915_GVT is enabled. (Tvrtko)
- Rebase the code into new repo.
- Add a comment about the ring buffer size. (Joonas)

v2:

Mostly based on Daniel's idea. Call the refactored core logic of GEM
context creation service and LRC context creation service to create the GVT
context.
Reviewed-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Signed-off-by: NZhi Wang <zhi.a.wang@intel.com>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1466078825-6662-10-git-send-email-zhi.a.wang@intel.com

This patch introduces the support of LRC context single submission.
As GVT context may come from different guests, which require different
configuration of render registers. It can't be combined into a dual ELSP
submission combo.

Only GVT-g will create this kinds of GEM context currently.

v8:

- Rename the data member in struct i915_gem_context. (Chris)

v7:

- Fix typos in commit message. (Joonas)

v6:
- Make GVT code as dead code when !CONFIG_DRM_I915_GVT. (Chris)

v5:

- Only compile this feature when CONFIG_DRM_I915_GVT=y. (Tvrtko)
Reviewed-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Signed-off-by: NZhi Wang <zhi.a.wang@intel.com>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1466078825-6662-9-git-send-email-zhi.a.wang@intel.com

This patch introduces an approach to track the execlist context status
change.

GVT-g uses GVT context as the "shadow context". The content inside GVT
context will be copied back to guest after the context is idle. And GVT-g
has to know the status of the execlist context.

This function is configurable when creating a new GEM context. Currently,
Only GVT-g will create the "status-change-notification" enabled GEM
context.

v10:

- Fix the identation. (Joonas)

v8:

- Remove the boolean flag in struct i915_gem_context. (Joonas)

v7:

- Remove per-engine ctx status notifiers. Use one status notifier for all
engines. (Joonas)
- Add prefix "INTEL_" for related definitions. (Joonas)
- Refine the comments in execlists_context_status_change(). (Joonas)

v6:

- When !CONFIG_DRM_I915_GVT, make GVT code as dead code then compiler
could automatically eliminate them for us. (Chris)
- Always initialize the notifier header, so it could be switched on/off
at runtime. (Chris)

v5:

- Only compile this feature when CONFIG_DRM_I915_GVT is enabled.(Tvrtko)

Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> (v8)
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Signed-off-by: NZhi Wang <zhi.a.wang@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1466078825-6662-8-git-send-email-zhi.a.wang@intel.comSigned-off-by: NChris Wilson <chris@chris-wilson.co.uk>

Currently the addressing mode bit in context descriptor is statically
generated from the configuration of system-wide PPGTT usage model.

GVT-g will load the PPGTT shadow page table by itself and probably one
guest is using a different addressing mode with i915 host. The addressing
mode bits of a LRC context should be configurable under this case.

v10:

- Fix the identation. (Joonas)

v9:
- Rename the data member in struct i915_gem_context. (Chris)

v8:
- Rename the data member in struct i915_gem_context. (Chris)

v7:
- Move context addressing mode bit into i915_reg.h. (Joonas/Chris)
- Add prefix "INTEL_" for related definitions. (Joonas)

v6:
- Directly save the addressing mode bits inside i915_gem_context. (Chris)
- Move the LRC context addressing mode bits into intel_lrc.h. (Chris)

v5:
- Change USES_FULL_48BIT(dev) to USES_FULL_48BIT(dev_priv) (Tvrtko)

Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> (v9)
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Signed-off-by: NZhi Wang <zhi.a.wang@intel.com>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1466078825-6662-7-git-send-email-zhi.a.wang@intel.com

This patch introduces an option for configuring the ring buffer size
of a LRC context after the context creation.

v9:
- Fix an identation issue. (Chris)

v8:
- Rename the data member in i915_gem_context. (Chris)
Reviewed-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NZhi Wang <zhi.a.wang@intel.com>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1466078825-6662-6-git-send-email-zhi.a.wang@intel.com

This patch introduces the very basic framework of GVT-g device model,
includes basic prototypes, definitions, initialization.

v12:
- Call intel_gvt_init() in driver early initialization stage. (Chris)

v8:
- Remove the GVT idr and mutex in intel_gvt_host. (Joonas)

v7:
- Refine the URL link in Kconfig. (Joonas)
- Refine the introduction of GVT-g host support in Kconfig. (Joonas)
- Remove the macro GVT_ALIGN(), use round_down() instead. (Joonas)
- Make "struct intel_gvt" a data member in struct drm_i915_private.(Joonas)
	- Remove {alloc, free}_gvt_device()
	- Rename intel_gvt_{create, destroy}_gvt_device()
	- Expost intel_gvt_init_host()
- Remove the dummy "struct intel_gvt" declaration in intel_gvt.h (Joonas)

v6:
- Refine introduction in Kconfig. (Chris)
- The exposed API functions will take struct intel_gvt * instead of
void *. (Chris/Tvrtko)
- Remove most memebers of strct intel_gvt_device_info. Will add them
in the device model patches.(Chris)
- Remove gvt_info() and gvt_err() in debug.h. (Chris)
- Move GVT kernel parameter into i915_params. (Chris)
- Remove include/drm/i915_gvt.h, as GVT-g will be built within i915.
- Remove the redundant struct i915_gvt *, as the functions in i915
will directly take struct intel_gvt *.
- Add more comments for reviewer.

v5:
Take Tvrtko's comments:
- Fix the misspelled words in Kconfig
- Let functions take drm_i915_private * instead of struct drm_device *
- Remove redundant prints/local varible initialization

v3:
Take Joonas' comments:
- Change file name i915_gvt.* to intel_gvt.*
- Move GVT kernel parameter into intel_gvt.c
- Remove redundant debug macros
- Change error handling style
- Add introductions for some stub functions
- Introduce drm/i915_gvt.h.

Take Kevin's comments:
- Move GVT-g host/guest check into intel_vgt_balloon in i915_gem_gtt.c

v2:
- Introduce i915_gvt.c.
It's necessary to introduce the stubs between i915 driver and GVT-g host,
as GVT-g components is configurable in kernel config. When disabled, the
stubs here do nothing.

Take Joonas' comments:
- Replace boolean return value with int.
- Replace customized info/warn/debug macros with DRM macros.
- Document all non-static functions like i915.
- Remove empty and unused functions.
- Replace magic number with marcos.
- Set GVT-g in kernel config to "n" by default.
Reviewed-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Cc: Kevin Tian <kevin.tian@intel.com>
Signed-off-by: NZhi Wang <zhi.a.wang@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1466078825-6662-5-git-send-email-zhi.a.wang@intel.comSigned-off-by: NChris Wilson <chris@chris-wilson.co.uk>