We always use zero delay before queueing a work on the ordered workqueue
('mlxsw_owq'), so use work_struct directly instead of delayable work.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

HTGT register length is limited to 32 bytes and not 256 bytes.
Signed-off-by: NElad Raz <eladr@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The mvneta itself does not support WOL, but the PHY might.
So pass the calls to the PHY
Signed-off-by: NJingju Hou <houjingj@marvell.com>
Signed-off-by: NJisheng Zhang <jszhang@marvell.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch switches the imx6 and vf610 based SoCs from the hardware FIFO
to the timestamp based rx offloading.
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

The flexcan IP core has 64 mailboxes. For now they are configured for
RX as a hardware FIFO. This FIFO has a fixed depth of 6 CAN frames. In
some high load scenarios it turns out thas this buffer is too small.

In order to have a buffer larger than the 6 frames FIFO, this patch adds
support for timestamp based offloading via the generic rx-offload
infrastructure.
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

In order to receive RTR frames in the non HW FIFO mode the RSS and EACEN bits
of the reg_ctrl2 have to be activated. As this has no side effect in the FIFO
mode, we do this unconditionally on cores with the reg_ctrl2.
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

Modern flexcan IP cores support two RX modes. One is using the 6 fames deep
hardware FIFO, the other is using up to 64 mailboxes (in non FIFO mode). For
now only the HW FIFO mode is activated.

In order to make use of the RX mailboxes the individual RX masking feature has
to be activated, otherwise matching mailboxes are overwritten during the
reception process. This however switches on the individual RX masking, which
uses reg_rximr registers for masking.

This patch activates the individual RX masking feature unconditionally and
initializes the mask registers (reg_rximr) with 0x0 == "don't care", which
switches off any filtering.
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

This patch converts the flexcan driver to make use of the rx-offload
can_rx_offload_irq_offload_fifo() helper function. The idea is to read
the CAN frames already in the interrupt context, as the depth of the
flexcan HW FIFO is too shallow, resulting in too many missed frames.
During a normal NAPI poll the frames are the pushed into the upper
layers.
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

This patch makes the TX mailbox selectable duing runtime. This is a preparation
patch to use of the hardware FIFO selectable via runtime. As the TX mailbox
number is different in HW FIFO and normal mode.
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

This patch converts the define FLEXCAN_IFLAG_DEFAULT into the runtime
calculated value priv->reg_imask1_default. This is a preparation patch to make
the TX mailbox selectable during runtime, too.
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

This patch changes the flexcan_irq() function to only return
IRQ_HANDLED, if the interrupt really has been handled, otherwise
IRQ_NONE is returned.
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

This patch folds in the do_bus_err() function into
flexcan_poll_bus_err().
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

This patch removed the not needed initialisation from the new_state,
rx_state, tx_state variabled.
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

This patch converts the rx_errors and tx_errors from int into bool
values, to reflect their actual meaning.
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

This patch changes the declaration of the devtype data to const.
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

This patch removes the write only member pdata from the struct
flexcan_priv.
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

This patch adds some missing register definitions, which are needed in an
upcoming patch.
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

Some CAN controllers don't implement a FIFO in hardware, but fill their
mailboxes in a particular order (from lowest to highest or highest to lowest).
This makes problems to read the frames in the correct order from the hardware,
as new frames might be filled into just read (low) mailboxes. This gets worse,
when following new frames are received into not read (higher) mailboxes.

On the bright side some these CAN controllers put a timestamp on each received
CAN frame. This patch adds support to offload CAN frames in interrupt context,
order them by timestamp and then transmitted in a NAPI context.
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

Some CAN controllers have a usable FIFO already but can still benefit
from off-loading the CAN controller FIFO. The CAN frames of the FIFO are
read and put into a skb queue during interrupt and then transmitted in a
NAPI context.
Signed-off-by: NDavid Jander <david@protonic.nl>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

We plan to remove __napi_complete() soon,
this driver is the last user.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use napi_complete_done() instead of __napi_complete()

We plan to remove __napi_complete() to reduce NAPI complexity.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use napi_complete_done() instead of __napi_complete() to :

1) Get support of gro_flush_timeout if opt-in
2) Not rearm interrupts for busy-polling users.
3) use standard NAPI API.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use napi_complete_done() instead of __napi_complete() to :

1) Get support of gro_flush_timeout if opt-in
2) Not rearm interrupts for busy-polling users.
3) use standard NAPI API.

Note that rx_lock seems to be useless, NAPI logic should
not need this extra care.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use napi_complete_done() instead of __napi_complete() to :

1) Get support of gro_flush_timeout if opt-in
2) Not rearm interrupts for busy-polling users.
3) use standard NAPI API and get rid of napi_gro_flush()
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use napi_complete_done() instead of __napi_complete() to :

1) Get support of gro_flush_timeout if opt-in
2) Not rearm interrupts for busy-polling users.
3) use standard NAPI API.
4) get rid of baroque code and ease maintenance.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use napi_complete_done() instead of __napi_complete() to :

1) Get support of gro_flush_timeout if opt-in
2) Not rearm interrupts for busy-polling users.
3) use standard NAPI API.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use napi_complete_done() instead of __napi_complete() to :

1) Get support of gro_flush_timeout if opt-in
2) Not rearm interrupts for busy-polling users.
3) use standard NAPI API.
4) get rid of baroque code and ease maintenance.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use napi_complete_done() instead of __napi_complete() to :

1) Get support of gro_flush_timeout if opt-in
2) Not rearm interrupts for busy-polling users.
3) use standard NAPI API.
4) get rid of baroque code and ease maintenance.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use napi_complete_done() instead of __napi_complete() to :

1) Get support of gro_flush_timeout if opt-in
2) Not rearm interrupts for busy-polling users.
3) use standard NAPI API.
4) Eventually get rid of napi_gro_flush() in the future.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use napi_complete_done() instead of __napi_complete() to :

1) Get support of gro_flush_timeout if opt-in
2) Not rearm interrupts for busy-polling users.
3) use standard NAPI API.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since commit 364b6055 ("net: busy-poll: return busypolling status to
drivers"), napi_complete_done() returns a boolean that can be used
by drivers to conditionally rearm interrupts.

This patch changes virtio_net to use this boolean to avoid a bit of
overhead for busy-poll users.

Jason reports about 1.1% improvement for 1 byte TCP_RR (burst 100).
Signed-off-by: NEric Dumazet <edumazet@google.com>
Acked-by: NJason Wang <jasowang@redhat.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Willem de Bruijn <willemb@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We do polling generically these days.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In linux-4.5, busy polling was implemented in core
NAPI stack, meaning that all custom implementation can
be removed from drivers.

Not only we remove lot's of code, we also remove one lock
operation in fast path, and allow GRO to do its job.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In linux-4.5, busy polling was implemented in core
NAPI stack, meaning that all custom implementation can
be removed from drivers.

Not only we remove lot's of code, we also remove one lock
operation in fast path, and allow GRO to do its job.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Extend the existing setup_tc ndo call and allow to offload cls_flower
rules. Only limited set of dissector keys and actions are supported now.
Use previously introduced ACL infrastructure to offload cls_flower rules
to be processed in the HW.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add ACL core infrastructure for Spectrum ASIC. This infra provides an
abstraction layer over specific HW implementations. There are two basic
objects used. One is "rule" and the second is "ruleset" which serves as a
container of multiple rules. In general, within one ruleset the rules are
allowed to have multiple priorities and masks. Each ruleset is bound to
either ingress or egress a of port netdevice.

The initial TCAM implementation is very simple and limited. It utilizes
parman lsort manager to take care of TCAM region layout.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add couple of resource limits related to ACL.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Introduce basic set of Spectrum flexible key blocks. It contains blocks
needed to carry all elements defined so far.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Each entry which is matched during ACL lookup points to an action set.
This action set contains up to three separate actions. If more actions
are needed to be chained, the extended set is created to hold them
in KVD linear area.

This patch implements handling of sets and encoding of actions.
Currectly, only two actions are supported. Drop and forward. Forward
action uses PBS pointer to KVD linear area, so the action code needs to
take care of this as well.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Hardware supports matching on so called "flexible keys". The idea is to
assemble an optimal key to use for matching according to the fields in
packet (elements) requested by user. Certain sets of elements are
combined into pre-defined blocks. There is a picker to find needed blocks.
Keys consist of 1..n blocks.

Alongside with that, an initial portion of elements is introduced in order
to be able to offload basic cls_flower rules.

Picked keys are cached so multiple rules could share them.

There is an encode function provided that takes care of encoding key and
mask values according to given key.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>