Some hardware require L2 padding between header and payload
because both must be aligned to a 4-byte boundary. This hardware
also is easier during the RX path since we no longer need to
move the entire payload but rather only the header to remove
the padding (mac80211 only wants the payload to be 4-byte aligned).
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

By placing the iv_len into the tx descriptor data and
by passing this data to the crypto IV handlers we can
save multiple calls to ieee80211_get_hdrlen_from_skb()
and some if-statements when copying/removing the IV data
from the outgoing frame.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

commit 8e218fb2 reverted the previous
patch (commit 925be8a3).

The C99 specification states in section 6.11.5:

The placement of a storage-class specifier other than at the
beginning of the declaration specifiers in a declaration is an
obsolescent feature.
Signed-off-by: NTobias Klauser <tklauser@distanz.ch>
Acked-by: NJiri Slaby <jirislaby@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

remove redundant test: outlen is unsigned
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Acked-by: NChristian Lamparter <chunkeey@web.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch takes care of an outstanding comment in
"[PATCH] ar9170usb: fix hang on resume" commit message.

>However, the device does not accept the firmware on resume.
>and it will exit with:
>
>> firmware part 1 upload failed (-71).
>> device is in a bad state. please reconnect it!
Reported-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NChristian Lamparter <chunkeey@web.de>
Tested-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch redo the driver code so that p54usb no longer hangs
the kernel on resume.
Signed-off-by: NChristian Lamparter <chunkeey@web.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Since "p54: prevent upload of wrong firmwares" we no longer allow
outdated LM86 firmwares to be uploaded on ISL3887 (LM87) devices.
Therefore we can purge this buggy legacy code altogether.
Signed-off-by: NChristian Lamparter <chunkeey@web.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Set null key type even on ar5211, otherwise it en/decrypts every frame with
protected bit set which renders the card unusable on encrypted networks.
Signed-off-by: NJiri Slaby <jirislaby@gmail.com>
Cc: Luis R. Rodriguez <lrodriguez@atheros.com>
Cc: Bob Copeland <me@bobcopeland.com>
Acked-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch uncomment a few lines that survived the RFCs.
However, there is not much to worry about, since AP mode is
not officially advertised and supported.
Signed-off-by: NChristian Lamparter <chunkeey@web.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Otus uses slightly different set of "Minimum MPDU Start Spacing" values
than the 802.11n D2.0 specifies. (the whole table is shifted by one and
therefore the 16us spacing is not officially available!)

And while we're at it, we also initialize our MAC's density register.
So, this annoying _feature_ will not break TX A-MPDU later.
Signed-off-by: NChristian Lamparter <chunkeey@web.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

A typo slipped into my patch to configure beacon intervals
properly -- this warning is supposed to trigger when the
beacon interval is zero, not non-zero.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The config_interface method is a little strange, it contains the
BSSID and beacon updates, while bss_info_changed contains most
other BSS information for each interface. This patch removes
config_interface and rolls all the information it previously
passed to drivers into bss_info_changed.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We currently have two beacon interval configuration knobs:
hw.conf.beacon_int and vif.bss_info.beacon_int. This is
rather confusing, even though the former is used when we
beacon ourselves and the latter when we are associated to
an AP.

This just deprecates the hw.conf.beacon_int setting in favour
of always using vif.bss_info.beacon_int. Since it touches all
the beaconing IBSS code anyway, we can also add support for
the cfg80211 IBSS beacon interval configuration easily.

NOTE: The hw.conf.beacon_int setting is retained for now due
      to drivers still using it -- I couldn't untangle all
      drivers, some are updated in this patch.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

char bname[5] is too small for the string "X GHz" when the null
terminator is taken into account.  Thus, turning on rate debugging
can crash unless we have lucky stack alignment.

Cc: stable@kernel.org
Reported-by: NParide Legovini <legovini@spiro.fisica.unipd.it>
Signed-off-by: NBob Copeland <me@bobcopeland.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Under certain circumstances iwlwifi can get stuck and will no
longer accept scan requests, because the core code (cfg80211)
thinks that it's still processing one. This fixes one of the
points where it can happen, but I've still seen it (although
only with my radio-off-when-idle patch).
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Acked-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

rndis_wext_link_change() might be called from rndis_command() at
initialization stage and priv->workqueue/priv->work have not been
initialized yet. This causes invalid opcode at rndis_wext_bind on
some brands of bcm4320.

Fix by initializing workqueue/workers in rndis_wext_bind() before
rndis_command is used.

This bug has existed since 2.6.25, reported at:
	http://bugzilla.kernel.org/show_bug.cgi?id=12794Signed-off-by: NJussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

drivers/net/wireless/iwlwifi/iwl3945-base.c:1415: error: __ksymtab_iwl3945_rx_queue_reset causes a section type conflict

I am pretty sure that this is a compiler bug, so not to worry.  However,
as far as I can see, iwl-3945.o (the only user) and iwl3945-base.o are
always linked into the same module, so the EXPORT_SYMBOL (which causes
the problem) should not be needed.  Correct?
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

net/mac80211/tx.c: In function ‘ieee80211_tx_h_select_key’:
net/mac80211/tx.c:448: warning: ‘key’ may be used uninitialized in this function

drivers/net/wireless/ath/ath9k/rc.c: In function ‘ath_rc_rate_getidx’:
drivers/net/wireless/ath/ath9k/rc.c:815: warning: ‘nextindex’ may be used uninitialized in this function

drivers/net/wireless/hostap/hostap_plx.c: In function ‘prism2_plx_probe’:
drivers/net/wireless/hostap/hostap_plx.c:438: warning: ‘cor_index’ may be used uninitialized in this function
drivers/net/wireless/hostap/hostap_plx.c:438: warning: ‘cor_offset’ may be used uninitialized in this function
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

drivers/net/wireless/libertas/if_spi.c: In function ‘if_spi_c2h_data’:
drivers/net/wireless/libertas/if_spi.c:733: warning: format ‘%u’ expects type ‘unsigned int’, but argument 4 has type ‘long unsigned int’
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Private structure is allocated by wiphy_new now, so use
wiphy_free instead of kfree.
Signed-off-by: NJussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

rndis_wext_link_change() might be called from rndis_command() at
initialization stage and priv->workqueue/priv->work have not been
initialized yet. This causes invalid opcode at rndis_wext_bind on
some brands of bcm4320.

Fix by initializing workqueue/workers in rndis_wext_bind() before
rndis_command is used.
Signed-off-by: NJussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

sparse complains, correctly, about these:

drivers/net/wireless/rndis_wlan.c:418:21: warning: symbol 'rndis_config_ops' was not declared. Should it be static?
drivers/net/wireless/rndis_wlan.c:423:6: warning: symbol 'rndis_wiphy_privid' was not declared. Should it be static?

Fix that.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Allow user to config the device all the time but only allow commiting
these changes to card if the card is up and running.
Signed-off-by: NMohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Patch removes the "manual radio disable" parameter
as there is no usage scenario of disabling radio using this module parameter.
User can use iwconfig's txpower to enable and disable radio.

This module parameter also does not work as expected. During module load
the status of radio is set, the radio is not actually disabled. Even so,
the moment mac80211 requests the interface to be up the radio will be
enabled again.
Signed-off-by: NAbhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Function rs_stay_in_table was flushing the rate scale table way to early. time_after
macro in expecting long value and was failing because we passing u32 value.
Signed-off-by: NMohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch clean up the code for NL80211_IFTYPE_MONITOR mode,
priv->iw_mode is set in add_interface, but add_interface is never called
for monitor mode.
The only way mac80211 informs us about monitor mode is through
configuring filter; since iw_mode will never set to
NL80211_IFTYPE_MONITOR, modify and remove all the code refer to
NL80211_IFTYPE_MONITOR and replace with iwl_is_monitor_mode() function
call.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch calculates interrupt statistics for debugfs.
Signed-off-by: NAbhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Patch adds debugfs to 3945. Also fix debugfs registration in iwlagn
to return error code if it fails.
Signed-off-by: NAbhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

If passive scanning is requested we should not ask the
microcode to do active scanning after detecting traffic
on a channel -- that should only be used when an active
scan is requested but some channels are marked passive.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This modifies iwlwifi to
 * no longer build its own probe request, but use mac80211's
 * therefore, support arbitrary scan IEs (up to the max len)
 * support multiple scan SSIDs
 * support passive scanning
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This limit applies to current (APIv1 and APIv2) 3945 firmware only, not
supported firmware of any of the other cards.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

With this patch ar9170 is capable of receiving aggregated 802.11n frames
and sniffing on most networks without having a "debug message overhead".

(Includes phy initialization requested by
Johannes Berg <johannes@sipsolutions.net> -- JWL)
Signed-off-by: NChristian Lamparter <chunkeey@web.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch adds support for configuring HT40 channels
and receiving HT40 to ar9170. Receiving aggregation
doesn't seem to work right now, so it's not enabled.
Same goes for TX aggregation, but that probably needs
even more work.

With this, I can receive roughly 33 Mbits/sec.

The HT capabilities are a little odd, I tried following
otus here -- in particular having SGI_40 but not SGI_20
is a little weird but afaict that's what otus does.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Supporting wireless extension nickname is pointless
and no other modern driver supports this, so remove
it.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Acked-by: NJussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Trying to separate header files into net/wireless.h and
net/cfg80211.h has been a source of confusion. Remove
net/wireless.h (because there also is the linux/wireless.h)
and subsume everything into net/cfg80211.h -- except the
definitions for regulatory structures which get moved to
a new header net/regulatory.h.

The "new" net/cfg80211.h is now divided into sections.

There are no real changes in this patch but code shuffling
and some very minor documentation fixes.

I have also, to make things reflect reality, put in a
copyright line for Luis to net/regulatory.h since that
is probably exclusively written by him but was formerly
in a file that only had my copyright line.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Cc: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

PS-Polled frames must be sent with OUT_NOCANCEL flag set,
or the firmware will reject all of them, at the station is still blacklisted.
Signed-off-by: NChristian Lamparter <chunkeey@web.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The following patch implements some control over the LED on RTL8187B and
RTL8187L devices. Triggers are registered for TX and RX. Whenever the
trigger event occurs, the LED is turned off for 1/20 second, then turned
back on.

Note: For those RTL8187X devices that are built into the computer and have
a LED that is expected to be controlled with a radio switch, this patch will
not operate that LED. That will take a separate patch to be prepared later.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NHerton Ronaldo Krzesinski <herton@mandriva.com.br>
Tested-by: NHin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

A detection function was added for identifying CF8381.
Signed-off-by: NMarek Vasut <marek.vasut@gmail.com>
Acked-by: NDan Williams <dcbw@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch deactivates powersave in station mode.

It does not work correctly yet, so the code does more harm than good.

(I split the original patch and sent part of it for 2.6.30, which didn't
have the IEEE80211_HW_BEACON_FILTER flag. -- JWL)
Reported-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NChristian Lamparter <chunkeey@web.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>