This patch ports more useful features to p54
  - PDR definitions for the synth chips & regulatory domain.
  - honour IEEE80211_TX_CTL_ASSIGN_SEQ flag, if it's set.
  - adds some lost mutex_lock & mutex_unlock.
  - replace two more "magic values" that sneaked past.
Signed-off-by: NChristian Lamparter <chunkeey@web.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Johannes thought it would have been a good idea to change the firmware names.

Note: we still have fallbacks in case our users don't want to "break their running system",
but we won't advertise them with MODULE_FIRMWARE.
Signed-off-by: NChristian Lamparter <chunkeey@web.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We have some reasons to kill netdev->priv:
1. netdev->priv is equal to netdev_priv().
2. netdev_priv() wraps the calculation of netdev->priv's offset, obviously
   netdev_priv() is more flexible than netdev->priv.
But we cann't kill netdev->priv, because so many drivers reference to it
directly.

OK, becasue Dave S. Miller said, "every direct netdev->priv usage is a bug",
and I want to kill netdev->priv later, I decided to convert all the direct
reference of netdev->priv first.

Different to readonly reference of netdev->priv, in this driver, netdev->priv
was changed. I use netdev->ml_priv to replace netdev->priv.
Signed-off-by: NWang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

I was recently hunting a bug that occurred in network namespace
cleanup.  In looking at the code it became apparrent that we have
and will continue to have cases where if we have anything going
on in a network namespace there will be assumptions that the
loopback device is present.   Things like sending igmp unsubscribe
messages when we bring down network devices invokes the routing
code which assumes that at least the loopback driver is present.

Therefore to avoid magic initcall ordering hackery that is hard
to follow and hard to get right insert a call to register the
loopback device directly from net_dev_init().    This guarantes
that the loopback device is the first device registered and
the last network device to go away.

But do it carefully so we register the loopback device after
we clear dev_boot_phase.
Signed-off-by: NEric W. Biederman <ebiederm@maxwell.aristanetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This reverts commit ae33bc40.

Write interrupt ack bit in fjn_interrupt for lan and modem to work
simultaneously.
Signed-off-by: NKomuro <komurojun-mbn@nifty.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

This patch fixes iwl3945 deadlock during suspend by moving notify_mac out
of iwl3945 mutex. This is a portion of the same fix for iwlwifi by Tomas.
Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Do not send scan command if no channels to scan.

This avoids a Microcode error as reported in:
http://www.intellinuxwireless.org/bugzilla/show_bug.cgi?id=1650
http://bugzilla.kernel.org/show_bug.cgi?id=11806
http://marc.info/?l=linux-wireless&m=122437145211886&w=2Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch ensures we clear any scan status bit when
an error occurs while sending the scan command. It is
the implementation of patch:
"iwlwifi: clear scanning bits upon failure"
for iwl3945.
Signed-off-by: NMohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

ath5k_rx_status fields rs_antenna and rs_more are u8s, but we
were setting them with bitwise ANDs of 32-bit values.

As a consequence, jumbo frames would not be discarded as intended.
Then, because the hw rate value of such frames is zero, and, since
"ath5k: rates cleanup", we do not fall back to the basic rate, such
packets would trigger the following WARN_ON:

------------[ cut here ]------------
WARNING: at net/mac80211/rx.c:2192 __ieee80211_rx+0x4d/0x57e [mac80211]()
Modules linked in: ath5k af_packet sha256_generic aes_i586 aes_generic cbc loop i915 drm binfmt_misc acpi_cpufreq fan container nls_utf8 hfsplus dm_crypt dm_mod kvm_intel kvm fuse sbp2 snd_hda_intel snd_pcm_oss snd_pcm snd_mixer_oss snd_seq_dummy snd_seq_oss arc4 joydev hid_apple ecb snd_seq_midi snd_rawmidi snd_seq_midi_event snd_seq snd_timer snd_seq_device usbhid appletouch mac80211 sky2 snd ehci_hcd ohci1394 bitrev crc32 sr_mod cdrom rtc sg uhci_hcd snd_page_alloc cfg80211 ieee1394 thermal ac battery processor button evdev unix [last unloaded: ath5k]
Pid: 0, comm: swapper Tainted: G        W  2.6.28-rc2-wl #14
Call Trace:
 [<c0123d1e>] warn_on_slowpath+0x41/0x5b
 [<c012005d>] ? sched_debug_show+0x31e/0x9c6
 [<c012489f>] ? vprintk+0x369/0x389
 [<c0309539>] ? _spin_unlock_irqrestore+0x54/0x58
 [<c011cd8f>] ? try_to_wake_up+0x14f/0x15a
 [<f81918cb>] __ieee80211_rx+0x4d/0x57e [mac80211]
 [<f828872a>] ath5k_tasklet_rx+0x5a1/0x5e4 [ath5k]
 [<c013b9cd>] ? clockevents_program_event+0xd4/0xe3
 [<c01283a9>] tasklet_action+0x94/0xfd
 [<c0127d19>] __do_softirq+0x8c/0x13e
 [<c0127e04>] do_softirq+0x39/0x55
 [<c0128082>] irq_exit+0x46/0x85
 [<c010576c>] do_IRQ+0x9a/0xb2
 [<c010461c>] common_interrupt+0x28/0x30
 [<f80e934a>] ? acpi_idle_enter_bm+0x2ad/0x31b [processor]
 [<c02976bf>] cpuidle_idle_call+0x65/0x9a
 [<c010262c>] cpu_idle+0x76/0xa6
 [<c02fb402>] rest_init+0x62/0x64
Signed-off-by: NBob Copeland <me@bobcopeland.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

07fa/1196
Bewan BWIFI-USB54AR: Tested by night1308, this device is a ZD1211B with
an AL2230S radio.

0ace/b215
HP 802.11abg: Tested by Robert Philippe
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

__ieee80211_tasklet_handler -> __ieee80211_rx ->
	__ieee80211_rx_handle_packet -> ieee80211_invoke_rx_handlers ->
	ieee80211_rx_h_decrypt -> ieee80211_crypto_tkip_decrypt ->
	ieee80211_tkip_decrypt_data -> iwl4965_mac_update_tkip_key ->
	iwl_scan_cancel_timeout -> msleep

Ooops!

Avoid the sleep by changing iwl_scan_cancel_timeout with
iwl_scan_cancel and simply returning on failure if the scan persists.
This will cause hardware decryption to fail and we'll handle a few more
frames with software decryption.
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In iwl_bg_request_scan function, if we could not send a
scan command it will go to done.
In done it does the right thing to call mac80211 with
scan complete, but the problem is STATUS_SCAN_HW is still
set causing any future scan to fail. Fix by clearing the scanning status
bits if scan fails.
Signed-off-by: NMohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Unfortunately, the result was that mac80211 didn't see all the beacons
it actually wanted to see.  This caused lost associations.

Hopefully we can revisit this when mac80211 is less greedy about seeing
beacons directly...

This reverts commit 06327906.
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Attached is a driver for SMSC's LAN911x and LAN921x families of embedded
ethernet controllers.

There is an existing smc911x driver in the tree; this is intended to
replace it.  Dustin McIntire (the author of the smc911x driver) has
expressed his support for switching to this driver.

This driver contains workarounds for all known hardware issues, and has
been tested on all flavours of the chip on multiple architectures.

This driver now uses phylib, so this patch also adds support for the
device's internal phy
Signed-off-by: NSteve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: NBahadir Balban <Bahadir.Balban@arm.com>
Signed-off-by: NDustin Mcintire <dustin@sensoria.com>
Signed-off-by: NBill Gatliff <bgat@billgatliff.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

This patch removes some trailing whitespaces and spaces before tabs.
Signed-off-by: NHannes Hering <hering2@de.ibm.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

The TX watchdog should trigger a reset, but a temperature/power alarm
should not as this is unlikely to solve the problem.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Add board monitoring to periodic work whenever link is down.
For SFE4001, report when a fault has caused the PHY to turn off.
For SFE4002, switch XFP PHY into low-power state in case of a fault.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

The boot code that appears as a PCI expansion ROM on the SFC4000 is
stored in flash.  Expose this as a standard MTD device to allow for
in-place upgrades.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Move flash and EEPROM partition boundary constants into spi.h and rename
them to be consistent.

Add a comment on the partitioning.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Due to a hardware bug, the originally assigned range cannot reliably
be used for boot configuration and must not be modifiable through
ethtool.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

	This patch implements alternative aggregator selection policies
for 802.3ad.  The existing policy, now termed "stable," selects the active
aggregator by greatest bandwidth, and only reselects a new aggregator
if the active aggregator is entirely disabled (no more ports or all ports
down).

	This patch adds two new policies: bandwidth and count, selecting
the active aggregator by total bandwidth (like the stable policy) or by
the number of ports in the aggregator, respectively.  These two policies
also differ from the stable policy in that they will reselect the active
aggregator when availability-related changes occur in the bond (e.g.,
link state change).

	This permits "gang failover" within 802.3ad, allowing redundant
aggregators along parallel paths to always maintain the "best" aggregator
as the active aggregator (rather than having to wait for the active to
entirely fail).

	This patch also updates the driver version to 3.5.0.
Signed-off-by: NJay Vosburgh <fubar@us.ibm.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

	The current ALB function that processes incoming ARPs
does not handle traffic for VLANs configured above bonding.  This causes
traffic on those VLANs to all be assigned the same slave.  This patch
corrects that misbehavior by locating the bonding interface nested below
the VLAN interface.

	Bug reported by Sven Anders <anders@anduras.de>, who also
tested an earlier version of this patch and confirmed that it resolved
the problem.
Signed-off-by: NJay Vosburgh <fubar@us.ibm.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

This patch adds better IPv6 failover support for bonding devices,
especially when in active-backup mode and there are only IPv6 addresses
configured, as reported by Alex Sidorenko.

- Creates a new file, net/drivers/bonding/bond_ipv6.c, for the
   IPv6-specific routines.  Both regular bonds and VLANs over bonds
   are supported.

- Adds a new tunable, num_unsol_na, to limit the number of unsolicited
   IPv6 Neighbor Advertisements that are sent on a failover event.
   Default is 1.

- Creates two new IPv6 neighbor discovery functions:

   ndisc_build_skb()
   ndisc_send_skb()

   These were required to support VLANs since we have to be able to
   add the VLAN id to the skb since ndisc_send_na() and friends
   shouldn't be asked to do this.  These two routines are basically
   __ndisc_send() split into two pieces, in a slightly different order.

- Updates Documentation/networking/bonding.txt and bumps the rev of bond
   support to 3.4.0.

On failover, this new code will generate one packet:

- An unsolicited IPv6 Neighbor Advertisement, which helps the switch
   learn that the address has moved to the new slave.

Testing has shown that sending just the NA results in pretty good
behavior when in active-back mode, I saw no lost ping packets for example.
Signed-off-by: NBrian Haley <brian.haley@hp.com>
Signed-off-by: NJay Vosburgh <fubar@us.ibm.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

I was recently hunting a bug that occurred in network namespace
cleanup.  In looking at the code it became apparrent that we have
and will continue to have cases where if we have anything going
on in a network namespace there will be assumptions that the
loopback device is present.   Things like sending igmp unsubscribe
messages when we bring down network devices invokes the routing
code which assumes that at least the loopback driver is present.

Therefore to avoid magic initcall ordering hackery that is hard
to follow and hard to get right insert a call to register the
loopback device directly from net_dev_init().    This guarantes
that the loopback device is the first device registered and
the last network device to go away.
Signed-off-by: NEric W. Biederman <ebiederm@xmission.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NJianjun Kong <jianjun@zeuux.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The generic packet receive code takes care of setting
netdev->last_rx when necessary, for the sake of the
bonding ARP monitor.

Drivers need not do it any more.

Some cases had to be skipped over because the drivers
were making use of the ->last_rx value themselves.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

	The only user of the net_device->last_rx field is bonding.
This patch adds a conditional update of last_rx to the bonding special
logic in skb_bond_should_drop, causing last_rx to only be updated when
the ARP monitor is running.

	This frees network device drivers from the necessity of
updating last_rx, which can have cache line thrash issues.
Signed-off-by: NJay Vosburgh <fubar@us.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch updates the version to 3.95.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds the BCM50610 to the list of phys supported by the
broadcom driver.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch makes the expansion register access routines a little more
formal.  They will be used by the following bcm50610 support patch.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds flow control support to Broadcom phys.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch refines support for the 5785 device.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch refines the phylib support in the tg3 driver.  The patch does
the following things :

* Rename tg3_mdio_config() to tg3_mdio_config_5785().  The 5785 will be
  the only device that will use it so the name might as well reflect
  that.
* Fix a memory leak if mdiobus_register() fails.
* Add code to deal with phy device detection failures.
* Add code to correct the supported list of phy features based on the
  MAC <=> PHY interface.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch allows WOL to be enabled for Broadcom phys under phylib
control.  The only exception is the AC131, which has a completely
different register set.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 12dac075 ("tg3: adapt tg3 to
use reworked PCI PM code") introduced the new PCI PM API to the tg3
driver.  The patch was understandably conservative, so this patch
elaborates on that work.

The patch starts by creating a single point in tg3_set_power_state()
to decide whether or not to enable WOL.  The rest of the code in
tg3_set_power_state() was then pivoted to use the result of this
decision.

The patch then makes sure the device is allowed to wakeup before
reporting whether or not WOL is currently enabled.  The final hunks of
the patch consolidate where the WOL capability and WOL enabled flags
are set to a single location.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, phylib reports appear with a eth%d prefix.  Move the line
after register_netdev() and place it alongside the other informative
messages.  Update nearby informative messages accordingly.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

With older versions of the NVRAM format, the driver may mistakenly
determine that APE is enabled.  Make sure this doesn't happen by
restricting the ENABLE_APE check to devices known to have more
recent NVRAM image formats.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch reclaims the TG3_FLG3_5761_5784_AX_FIXES flag.  It only
used twice in non-fast paths.  This patch also consolidates some other
places where specific 5784 AX chip revisions can be generalized.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>