It adds device tree support for imx51 babbage board.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Acked-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

The patch extends card_detect and write_protect support to get mx5
family and more scenarios supported.  The changes include:

 * Turn platform_data from optional to mandatory
 * Add cd_types and wp_types into platform_data to cover more use
   cases
 * Remove the use of flag ESDHC_FLAG_GPIO_FOR_CD
 * Adjust some machine codes to adopt the platform_data changes
 * Work around the issue that software reset will get card detection
   circuit stop working

With this patch, card_detect and write_protect gets supported on
mx5 based platforms.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Cc: Chris Ball <cjb@laptop.org>
Acked-by: NWolfram Sang <w.sang@pengutronix.de>
Tested-by: NArnaud Patard <arnaud.patard@rtp-net.org>
Acked-by: NChris Ball <cjb@laptop.org>

On MX51 Babbage board the RTS/CTS pins are not used on UART2 port.

Fix the registration of this port.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: NAndre Silva <andre.silva@freescale.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Instead of using gpio_request followed by gpio_direction_output use gpio_request_array
when requesting multiple pins.

Also fixed the location of the delay for the reset and make the BABBAGE_USB_PHY_RESET to toggle.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

The USB PHY Reset GPIO can be configured in the same place as the other GPIOs.

While at it rename the pin as BABBAGE_USB_PHY_RESET to make clearer its purpose.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

The patch makes necessary changes on gpio-mxc as below to turn it
into an upstanding gpio driver.

 * Add a list to save all mx2 ports references, so that
   mx2_gpio_irq_handler can walk through all interrupt status
   registers

 * Use readl/writel to replace mach-specific accessors
   __raw_readl/__raw_writel

 * Change mxc_gpio_init into mxc_gpio_probe function

 * Move "struct mxc_gpio_port" into gpio-mxc.c, as it needs not to
   be public at all, and also make some other cleanup on
   plat-mxc/include/mach/gpio.h at the same time

And the patch then migrates mach-imx and mach-mx5 to the updated
driver by adding corresponding platform devices.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Acked-by: NOlof Johansson <olof@lixom.net>
Acked-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

There is no need for using a MX51-specific version of imx_add_gpio_keys.

Remove imx51_add_gpio_keys and use imx_add_gpio_keys instead.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
LAKML-Reference: 1302105926-20574-1-git-send-email-fabio.estevam@freescale.com
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Most machine files include "devices-imxXX.h" which in turn includes
<mach/devices-common.h>.  The latter already includes many headers
that the machine files don't need to include again.

These were found by:

 $ grep \#include arch/arm/plat-mxc/include/mach/devices-common.h > tmpfile
 $ git grep -l 'devices-imx' arch/arm | xargs grep -f tmpfile -F

(but I kept linux/init.h, linux/kernel.h and linux/platform_device.h)

LAKML-Reference: 1298912674-15153-2-git-send-email-u.kleine-koenig@pengutronix.de
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Current code inside babbage_usbhub_reset uses gpio_direction_output with initial value of the GPIO and also sets
the GPIO value via gpio_set_value to the same level right after. This is not needed.

By using gpio_request_one it is possible to set the direction and initial value in one shot.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
LAKML-Reference: 1300377359-23212-2-git-send-email-fabio.estevam@freescale.com
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Current code inside babbage_fec_reset uses gpio_direction_output with initial value of the GPIO and also sets
the GPIO value via gpio_set_value to the same level right after. This is not needed.

By using gpio_request_one it is possible to set the direction and initial value in one shot.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Acked-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

mxc_board_init is too generic to be useful.  Additionally change some
mxc_timer to ${machine}_timer, too.
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

The mxc-ehci driver calls SoC specific phy initialization right after
calling board specific initialization. To offer greater flexibility for
boards to setup the phy and to get rid of some unnecessary flags in
platform data this patch lets the boards call the SoC specific phy
initialization and remove it from the driver.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

This used to be done in .map_io which is supposed to only setup the
memory mapping.
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

This iomux file has been constructed from the Freescale pinmux tool.
It contains all pins from the tool, but the datasheet lists some
configurations not present in the tool, these are not yet added.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

This patch actually replaces the 'struct pad_desc' with a u64 cookie
to facilitate adding platform specific pad_ctrl settings to an
existing pad definition.

So, instead of:
	iomux_v3_cfg_t power_key = MX51_PAD_EIM_A27__GPIO_2_21;
	power_key.pad_ctrl = MX51_GPIO_PAD_CTRL_2;
	mxc_iomux_v3_setup_pad(&power_key);
one can write:
	mxc_iomux_v3_setup_pad((MX51_PAD_EIM_A27__GPIO_2_21 & ~MUX_PAD_CTRL_MASK) | MX51_GPIO_PAD_CTRL_2);

Patch applies to branch 'imx-for-2.6.38' of git://git.pengutronix.de/git/imx/linux-2.6Signed-Off-By: NLothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Currently, to define a GPIO number, we're using something like :

#define EFIKAMX_PCBID0         (2*32 + 16)

to define GPIO 3 16.

This is not really readable and it's error prone imho (note the 3 vs 2).
So, I'm introducing a new macro to define this in a better way. Now, the
code sample become :

#define EFIKAMX_PCBID0         IMX_GPIO_NR(3, 16)

v2:
- move to gpio.h
- add parens & spaces
- switch to IMX_GPIO_NR instead of MX51_GPIO_NR
Signed-off-by: NArnaud Patard <arnaud.patard@rtp-net.org>
Cc: Amit Kucheria <amit.kucheria@linaro.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Eric Bénard <eric@eukrea.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

MX51 Babbage has an AT45DB321 SPI Flash connected to eCSPI1.

Add support for it.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
Acked-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>

The following patch is a first step to convert the 'struct pad_desc'
to a bitmapped cookie to facilitate adding platform specific pullup or
drive strength definitions to existing pad definitions without need to
rewrite the complete pad def.

The patch wraps 'struct pad_desc' in an opaque data type and
introduces macros to access the individual members.
This patch does not constitute any functional change!
Signed-off-by: NLothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

and restore alphabetic ordering.
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>

Add functionality for the power button on MX51 Babbage board.
Signed-off-by: NDinh Nguyen <Dinh.Nguyen@freescale.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Currently, only two operating points: 160Mhz and 800Mhz.
the operating points are tested on babbage 3.0
Signed-off-by: NYong Shen <yong.shen@linaro.org>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Update babbage board support to register esdhc device
Signed-off-by: NShawn Guo <shawn.gsc@gmail.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Since we're now using addruart to establish the debug mapping, we can
remove the io_pg_offst and phys_io members of struct machine_desc.

The various declarations were removed using the following script:

  grep -rl MACHINE_START arch/arm | xargs \
  sed -i '/MACHINE_START/,/MACHINE_END/ { /\.\(phys_io\|io_pg_offst\)/d }'

[ Initial patch was from Jeremy Kerr, example script from Russell King ]
Signed-off-by: NNicolas Pitre <nicolas.pitre@linaro.org>
Acked-by: Eric Miao <eric.miao at canonical.com>

Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>

Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>

Tested it by booting a rootfs via NFS.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>

The pads capable of being used as GPIOs had their pad-name and mode-name
switched. Also, fix the following:

- Whitespace fixes
- Replace IOMUX_CONFIG_ALTn with 'n'
Signed-off-by: NAmit Kucheria <amit.kucheria@canonical.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Add device registration and setup IOMUX pins in the mx51_babbage
board feil.
Signed-off-by: NDinh Nguyen <Dinh.Nguyen@freescale.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

This patch de-asserts the reset line that is connected to the USB
ULPI PHY on USB Host1.

This patch should be included with the original USB host enablement
set of patches of mx51 babbage hw, but was accidentily left out.
Signed-off-by: NDinh Nguyen <Dinh.Nguyen@freescale.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

This patch enables usb gadget for freescale mx51 babbage hw. By default,
the OTG port will be in device mode. To put the OTG port into Host mode,
pass "otg_mode=host" in the exec command.

This patch applies to 2.6.34-rc7.
Signed-off-by: NDinh Nguyen <Dinh.Nguyen@freescale.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

This patch enables USB host functionality for Host1 and OTG port on
Freescale MX51 Babbage HW. This patch contains the board specific
HW initialization of the USB HW.

This patch applies to 2.6.34-rc6.
Signed-off-by: NDinh Nguyen <Dinh.Nguyen@freescale.com>
Reviewed-by: NDaniel Mack <daniel@caiaq.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

This patch is to be applied into Sascha's mxc-master branch.

Fix ckih2 parameter in mx51_clocks_init funtion. CKIH2 pin is left unconnected on Babbage.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Acked-by: NAmit Kucheria <amit.kucheria@canonical.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Babbage is a reference board from Freescale for their i.MX51 SoC.

Add board definition, Kconfig and Makefiles to enable Freescale i.MX51
processor and Babbage board.

Boot tested on a Babbage2.5 board
Signed-off-by: NAmit Kucheria <amit.kucheria@canonical.com>