- 13 8月, 2013 7 次提交
-
-
由 Amit Daniel Kachhap 提交于
This patch adds support for h/w mode calibration in the TMU controller. Soc's like 5440 support this features. The h/w bits needed for calibration setting are same as that of enum calibration_type. Acked-by: NJonghwa Lee <jonghwa3.lee@samsung.com> Acked-by: NKukjin Kim <kgene.kim@samsung.com> Signed-off-by: NAmit Daniel Kachhap <amit.daniel@samsung.com> Signed-off-by: NEduardo Valentin <eduardo.valentin@ti.com>
-
由 Amit Daniel Kachhap 提交于
This patch adds configuration data for exynos5440 soc. Also register definations for the controller are added. Acked-by: NJonghwa Lee <jonghwa3.lee@samsung.com> Acked-by: NKukjin Kim <kgene.kim@samsung.com> Signed-off-by: NAmit Daniel Kachhap <amit.daniel@samsung.com> Acked-by: NEduardo Valentin <eduardo.valentin@ti.com> Signed-off-by: NEduardo Valentin <eduardo.valentin@ti.com>
-
由 Amit Daniel Kachhap 提交于
This patch modifies TMU controller to add changes needed to work with exynos5440 platform. This sensor registers 3 instance of the tmu controller with the thermal zone and hence reports 3 temperature output. This controller supports upto five trip points. For critical threshold the driver uses the core driver thermal framework for shutdown. Acked-by: NJonghwa Lee <jonghwa3.lee@samsung.com> Acked-by: NKukjin Kim <kgene.kim@samsung.com> Signed-off-by: NJungseok Lee <jays.lee@samsung.com> Signed-off-by: NAmit Daniel Kachhap <amit.daniel@samsung.com> Acked-by: NEduardo Valentin <eduardo.valentin@ti.com> Signed-off-by: NEduardo Valentin <eduardo.valentin@ti.com>
-
由 Amit Daniel Kachhap 提交于
This patch adds support to handle multiple instances of the TMU controllers. This is done by removing the static structure to register with the core thermal and creating it dynamically for each instance of the TMU controller. The interrupt is made shared type to handle shared interrupts. Now since the ISR needs the core thermal framework to be registered so request_irq is moved after the core registration is done. Also the identifier of the TMU controller is extracted from device tree alias. This will be used for TMU specific initialisation. Acked-by: NKukjin Kim <kgene.kim@samsung.com> Acked-by: NJonghwa Lee <jonghwa3.lee@samsung.com> Signed-off-by: NAmit Daniel Kachhap <amit.daniel@samsung.com> Acked-by: NEduardo Valentin <eduardo.valentin@ti.com> Signed-off-by: NEduardo Valentin <eduardo.valentin@ti.com>
-
由 Amit Daniel Kachhap 提交于
TMU urgently sends active-high signal (thermal trip) to PMU, and thermal tripping by hardware logic. Thermal tripping means that PMU cuts off the whole power of SoC by controlling external voltage regulator. Acked-by: NKukjin Kim <kgene.kim@samsung.com> Acked-by: NJonghwa Lee <jonghwa3.lee@samsung.com> Acked-by: NEduardo Valentin <eduardo.valentin@ti.com> Signed-off-by: NJonghwan Choi <jhbird.choi@samsung.com> Signed-off-by: NAmit Daniel Kachhap <amit.daniel@samsung.com> Signed-off-by: NEduardo Valentin <eduardo.valentin@ti.com>
-
由 Amit Daniel Kachhap 提交于
This patch migrates the TMU register definition/bitfields to data file. This is needed to support SoC's which use the same TMU controller but register validity, offsets or bitfield may slightly vary across SOC's. Acked-by: NKukjin Kim <kgene.kim@samsung.com> Acked-by: NJonghwa Lee <jonghwa3.lee@samsung.com> Acked-by: NEduardo Valentin <eduardo.valentin@ti.com> Signed-off-by: NAmit Daniel Kachhap <amit.daniel@samsung.com> Signed-off-by: NEduardo Valentin <eduardo.valentin@ti.com>
-
由 Amit Daniel Kachhap 提交于
This code splits the exynos tmu driver code into SOC specific data parts. This will simplify adding new SOC specific data to the same TMU controller. Acked-by: NKukjin Kim <kgene.kim@samsung.com> Acked-by: NJonghwa Lee <jonghwa3.lee@samsung.com> Acked-by: NEduardo Valentin <eduardo.valentin@ti.com> Signed-off-by: NAmit Daniel Kachhap <amit.daniel@samsung.com> Signed-off-by: NEduardo Valentin <eduardo.valentin@ti.com>
-
- 14 3月, 2012 1 次提交
-
-
由 Rob Herring 提交于
Several platforms incorrectly use __io() for casting to 'void __iomem *'. This converts all of those uses to use the common IOMEM macro. Reported-by: NArnd Bergmann <arnd@arndb.de> Signed-off-by: NRob Herring <rob.herring@calxeda.com> Acked-by: NAnton Vorontsov <cbouatmailru@gmail.com> Cc: Russell King <linux@arm.linux.org.uk> Cc: Paul Mundt <lethal@linux-sh.org> Cc: Magnus Damm <magnus.damm@gmail.com> Cc: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com> Acked-by: NLinus Walleij <linus.walleij@linaro.org> Cc: linux-sh@vger.kernel.org Acked-by: NArnd Bergmann <arnd@arndb.de>
-
- 24 7月, 2009 1 次提交
-
-
由 Catalin Marinas 提交于
This patch defines the IO_ADDRESS macro for the !CONFIG_MMU case. Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>
-
- 10 11月, 2008 1 次提交
-
-
由 Catalin Marinas 提交于
Since boards like PB11MPCore have 512MB of RAM and 128MB of flash, the virtual space is short on vmalloc memory and mapping the flash fails. This patch changes the IO_ADDRESS so that static mappings start at 0xfc000000 and moves the PCI virtual addresses higher up. The new VMALLOC_END is set to 0xf8000000 (512MB higher than the old value). Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>
-
- 07 8月, 2008 1 次提交
-
-
由 Russell King 提交于
This just leaves include/asm-arm/plat-* to deal with. Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
- 19 4月, 2008 1 次提交
-
-
由 Catalin Marinas 提交于
This patch changes the IO_ADDRESS macro for the RealView platforms to accomodate a wider range of physical addresses on PB11MPCore. Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>
-
- 05 2月, 2008 1 次提交
-
-
由 Catalin Marinas 提交于
This patch moves the platform specific definitions from platform.h into the board-eb.h file. It drops the INT_* definitions as they are no longer used in irqs.h (moved to board-eb.h). It renames REALVIEW_* macros to REALVIEW_EB_* or REALVIEW_EB11MP_* to distinguish between standard EB and EB + the ARM11MPCore tile. The platform.h file contains common definitions to the RealView platforms and it is only directly included in board-*.h files. Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com> Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
- 15 2月, 2007 1 次提交
-
-
由 Catalin Marinas 提交于
The kernel originally supported revB only. This patch enables revC by default and adds a config option for building the kernel for the revB platform. Since the SCU base address was hard-coded in the proc-v6.S file (and only valid for RealView/EB revB), this patch also adds a more generic support for defining the SCU information. Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com> Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
- 16 11月, 2005 1 次提交
-
-
由 Russell King 提交于
Move __io_address to arch-realview/hardware.h, drop core.h from platsmp.c and localtimer.c, and include asm/io.h where required. Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
- 31 10月, 2005 1 次提交
-
-
由 Catalin Marinas 提交于
Support for RealView EB. Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com> Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
- 17 4月, 2005 1 次提交
-
-
由 Linus Torvalds 提交于
Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip!
-