Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Set main_gaintb and alt_gaintb once instead of zero'ing them
in every case.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Instead of trying to determine whether antenna diversity is
enabled by parsing eeprom data, use ATH9K_HW_CAP_ANT_DIV_COMB
which is already filled at init time.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Update the 'hw_timer_enabled' to 'false' wherever we are stopping
hardware generic timers, excecpt the case where we start them
again immediately.
Signed-off-by: NMohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Upon handling an e-scan result event from the firmware in
brcmf_cfg80211_escan_handler() the status may indicate e-scan
is completed or aborted. If so brcmf_notify_escan_complete()
is called. However, that function and brcmf_cfg80211_escan_handler()
both log the same debug message and both enable MPC flag in the
firmware.
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch assures data is only appended in output buffer when
data is not NULL and datalen is not zero.
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch fixes bug where driver frees resources twice when
an exception occurs.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

SDIO in-band interrupt is level sensitive according to SDIO standard.
When the register interrupt handler gets called by SDIO stack it is
running in non interrupt context and expected to clear the interrupt
from the dongle. Therefore in-band and out-of-band interrupt need to
be handled differently.

Cc: Wei Ni <wni@nvidia.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Reported-by: NWei Ni <wni@nvidia.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NFranky Lin <frankyl@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Tested-by: NStephen Warren <swarren@wwwdotorg.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Use SDIO host lock to protect the entire communication process
of register access or data read/write rather than function calls
to MMC/SDIO stack only. This can help to avoid unintentional
memory access and unexpected interruption.
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NFranky Lin <frankyl@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Streamline SDIO dpc by removing some unnecessary code path.
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NFranky Lin <frankyl@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Switch SDIO dpc implementation from kernel thread to workqueue for
better performance and compatibility.
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NFranky Lin <frankyl@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Interrupt pending flag used in SDIO bus layer could be used in
multiple processes in different context. Use atomic_t make sure
every interrupt is handled.
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NFranky Lin <frankyl@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Remove sdio bus sleep mechanism since it is never invoked.
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NFranky Lin <frankyl@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

brcmf_sendpkt only called by brcmf_netdev_start_xmit now. Absorb it
to increase readability.
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NFranky Lin <frankyl@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Inside ath9k_hif_usb_firmware_fail(), the instance of
'struct struct hif_device_usb' may be freed by
ath9k_hif_usb_disconnect() after

	complete(&hif_dev->fw_done);

But 'hif_dev' is still accessed after the line code
above is executed.

This patch fixes the issue by not accessing 'hif_dev'
after 'complete(&hif_dev->fw_done)' inside
ath9k_hif_usb_firmware_fail().

Cc: ath9k-devel@lists.ath9k.org
Cc: "Luis R. Rodriguez" <mcgrof@qca.qualcomm.com>
Cc: Jouni Malinen <jouni@qca.qualcomm.com>
Cc: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Cc: "John W. Linville" <linville@tuxdriver.com>
Signed-off-by: NMing Lei <ming.lei@canonical.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Right now MCI work is being queued twice by profile and status
updation. Queue MCI work once when it is needed.
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Ensure that led pin is filled and set to OFF before starting
the driver. With recent changes, drv_start is being called even
before led_init is being completed. This is causing led is always
OFF on driver load when the interface is UP. This patch splits the
led init and fills the led pin before register hw.
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Update all coex parameters in sigle place. So that we can avoid
redoing the same operation in mutiple places and it eases debugging.
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Before processing BT profiles or status messages, check whether
it is requested to flush BT profile. Otherwise it might increase
number of BT profiles that affects the WLAN performance. Also
flush the profiles when MCI is recovering from broken rx. After
flushing BT profiles, query BT topology to refetch them.
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When the 9462 is operating in 2G mode and MCI is enabled then
reduce the selfgen chain mask to chain 1. Otherwise poor performance
was reported at short range at Rx side when COEX is enabled.
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

During fast channel change, perform 2g5g_switch before starting
noisefloor calibration to avoid nfload timeout.
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Set the driver specific SGI flag based on the station's
HT capabilities, otherwise rate control uses the wrong rate.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

All of the rtlwifi-family of drivers have been in the kernel since 3.1
or earlier. The dependence on EXPERIMENTAL can be removed.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch adds e-scan support (currently i-scan is in use). E-scan
is a more powerful and memory efficient method for scanning. E-scan
will be the default scan method and eventually, i-scan support will
be removed. The scan methods do not make any difference to the end-user.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NFranky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch removes usage of some of the local data in the usb
host interface driver. This is a step in the preperation to
support multiple USB devices.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch fixes a bug where rx buffer does not get refilled if the
packet received has an rx protocol error.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Clean up scan related code in preparation of a new scan mechanism (e-scan)
which will follow in a separate patch.
Reviewed-by: NFranky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Enable tx flow control for USB host interface.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Firmware events can contain extra data. This patch adds support to
copy this data when it exists.
Reviewed-by: NFranky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When tx flow is to be blocked due to host interface throttle then
all net if queues should be stopped.
Reviewed-by: NFranky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

CMD_MAC_CONTROL is currently sent async to the firmware, and is sent
from the lbs_setup_firmware() path during device init.

This means that device init can complete with commands pending, and
the if_sdio driver will sometimes power down the device (after init)
with this command still pending.

This was causing an occasional spurious command timeout after init,
leading to a device reset.

Fix this by making CMD_MAC_CONTROL synchronous when called from the
lbs_setup_firmware() path.
Signed-off-by: NDaniel Drake <dsd@laptop.org>
Signed-off-by: NDan Williams <dcbw@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The register macros for antenna diversity are common for
AR9462 and AR9565, rename them.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch adds separate tx packet descriptor routine for AP
interface. This function fills bss_type, bss_num, wmm packet
delay information etc for TxPD going on AP interface.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Some platforms do not support WOW. Let's change the default wakeup
criteria to 0.
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

country 00 (world regulatory domain) doesn't define channels
52 - 64 and 100 - 140. Add these channels to our custom world
regulatory domain.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We will use world regulatory domain (country 00) as default
when driver is loaded. Later after a successful association
cfg80211 will change the regulatory domain to a specific country
if the AP has advertised country IE.
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

AP's country ie is parsed and 11d information is updated in firmware
while associating. Previous mwifiex_send_domain_info_cmd_fw() call in
association path is not necessary now. Hence it is removed in this
patch.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

"adapter->bss_prio_tbl[j].bss_prio_head" points to linked list of
interfaces with priority 'j'. "bss_prio_tbl[j].bss_prio_cur" is
supposed to point to next interface every time the routine for
dequeuing the packet is called. This ensures that each interface
gets fair chance.

Currently we have AP and station interfaces with priority '0'.
Therefore "adapter->bss_prio_tbl[0].bss_prio_cur" should
alternately point to AP and station nodes. Since "bss_prio_cur"
is not correctly updated, for each packet picked for AP, two
packets are picked for station interface.

This patch fixes the problem by correctly updating "bss_prio_cur".
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>