Currently, force_pio is cleared when the driver exits.  Then, it
resulted in clearing it in multiple places since MMC drivers in
general have multiple exit points.

 tmio_mmc_reset_work - bails out on timeout
 tmio_process_mrq - error out when it cannot send a command
 tmio_mmc_finish_request - successful exit

This is error-prone since we may miss to cover all bail-out points.

To simplify the code, the data structure should be initialized just
before used since we have a single entrance.  force_pio is only used
for data transfer, so tmio_mmc_start_data() will be a suitable place
to clear this flag.
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

As far as I tested the IP on UniPhier SoCs, TMIO_STAT_{RXRDY,TXRQ}
are asserted for DMA mode as well as for PIO.  I need to disable the
those IRQs in dma_ops->start hook, otherwise the DMA transfer fails
with the following error message:
  PIO IRQ in DMA mode!

Renesas chips are the same cases since I see their dma_ops->start
hooks explicitly clear TMIO_STAT_{RXRDY,TXRQ} (with nice comment!).

If we do this sanity check in TMIO MMC core, RXRDY/TXRQ handling
should be entirely moved to the core.  tmio_mmc_cmd_irq() will
be a suitable place to disable them.

The probe function sets TMIO_MASK_{READOP,WRITEOP} but this is odd.

    /* Unmask the IRQs we want to know about */
    if (!_host->chan_rx)
            irq_mask |= TMIO_MASK_READOP;
    if (!_host->chan_tx)
            irq_mask |= TMIO_MASK_WRITEOP;

At this point, _host->{chan_rx,chan_tx} are _always_ NULL because
tmio_mmc_request_dma() is called after this code.  Consequently,
TMIO_MASK_{READOP,WRITEOP} are set here whether DMA is used or not.
Remove this pointless code.
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Reviewed-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: NWolfram Sang <wsa+renesas@sang-engineering.com>

The TMIO mmc cannot detect the card insertion in native_hotplug mode
if the driver is probed without a card inserted.

The reason is obvious; all IRQs are disabled by tmio_mmc_host_probe(),
as follows:

  tmio_mmc_disable_mmc_irqs(_host, TMIO_MASK_ALL);

The card event IRQs are first enabled by tmio_mmc_start_command() as
follows:

  if (!host->native_hotplug)
          irq_mask &= ~(TMIO_STAT_CARD_REMOVE | TMIO_STAT_CARD_INSERT);
  tmio_mmc_enable_mmc_irqs(host, irq_mask);

If the driver is probed without a card, tmio_mmc_start_command() is
never called in the first place.  So, the card is never detected.

The card event IRQs must be enabled in probe/resume functions.
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Tested-by: NWolfram Sang <wsa+renesas@sang-engineering.com>

A card detect GPIO is set up only for platforms with "cd-gpios"
DT property or TMIO_MMC_USE_GPIO_CD flag.  However, the driver
core always uses mmc_gpio_get_cd, which just fails with -ENOSYS
if ctx->cd_gpio is unset.

The bit 5 of the status register provides the current signal level
of the CD line.  Allow to use it if the GPIO is unused.
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Tested-by: NWolfram Sang <wsa+renesas@sang-engineering.com>

This property is equivalent to "disable-wp" defined in
Documentation/devicetree/bindings/mmc/mmc.txt

The TMIO MMC core calls mmc_of_parse(), and it sets
MMC_CAP2_NO_WRITE_PROTECT if "disable-wp" property is present.

We do not need a vendor-specific property to do the same thing.

Let's remove the description from the dt-binding to prevent new boards
from using it.

I am keeping the driver code for existing DT files, but added
comments that this is deprecated.
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: NRob Herring <robh@kernel.org>
Reviewed-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Tested-by: NWolfram Sang <wsa+renesas@sang-engineering.com>

The use of this flag has been replaced with MMC_CAP2_NO_WRITE_PROTECT.
No platform defines this flag any more.  Remove.
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: NLee Jones <lee.jones@linaro.org>
Reviewed-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Tested-by: NWolfram Sang <wsa+renesas@sang-engineering.com>

TMIO_MMC_WRPROTECT_DISABLE is equivalent to MMC_CAP2_NO_WRITE_PROTECT.

Only the difference is the TMIO_... makes tmio_mmc_get_ro() return 0
(i.e. it does not affect mmc_gpio_get_ro() at all), while MMC_CAP2_...
returns 0 before calling ->get_ro() hook (i.e. it affects both IP own
logic and GPIO detection).

The TMIO MMC drivers do not set-up gpio_ro by themselves.  Only the
possibility, if any, would be DT specifies "wp-gpios" property, and
gpio_ro is set by mmc_gpiod_request_ro() called from mmc_of_parse().
However, it does not make sense to specify "wp-gpios" property and
"toshiba,mmc-wrprotect-disable" at the same time.

I checked under arch/arm/boot/dts/ and arch/arm64/boot/dts/renesas/,
and I did not see any Renesas boards with "wp-gpios".  So, this
conversion should be safe.
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Tested-by: NWolfram Sang <wsa+renesas@sang-engineering.com>

TMIO_MMC_WRPROTECT_DISABLE is equivalent to MMC_CAP2_NO_WRITE_PROTECT.

The flag is propagated as follows:
       renesas_sdhi_of_data::capabilities2
    -> tmio_mmc_data::capabilities2
    -> mmc_host::caps2

Only the difference is the TMIO_... makes tmio_mmc_get_ro() return 0
(i.e. it does not affect mmc_gpio_get_ro() at all), while MMC_CAP2_...
returns 0 before calling ->get_ro() hook (i.e. it affects both IP own
logic and GPIO detection).

The TMIO MMC drivers do not set-up gpio_ro by themselves.  Only the
possibility, if any, would be DT specifies "wp-gpios" property, and
gpio_ro is set by mmc_gpiod_request_ro() called from mmc_of_parse().
However, it does not make sense to specify "wp-gpios" property and
TMIO_MMC_WRPROTECT_DISABLE at the same time.

I checked under arch/arm/boot/dts/ and arch/arm64/boot/dts/renesas/,
and I did not see any Renesas boards with "wp-gpios".  So, this
conversion should be safe.
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Tested-by: NWolfram Sang <wsa+renesas@sang-engineering.com>

According to the BCM2835 datasheet there are no preset value registers.
This wasn't an issue before, because we didn't propagate 1.8V support.
Signed-off-by: NStefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The TODO section from 2010 is obsolete. We have DMA and PM meanwhile and
we always want to handle errors better, if possible. Also DRIVER_VERSION
is not used anymore these days.
Signed-off-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: NSimon Horman <horms+renesas@verge.net.au>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Add SDHCI_QUIRK2_PRESET_VALUE_BROKEN quirk as setting preset values loads
incorrect CLKD values (for UHS modes).

Remove SDHCI_QUIRK2_NO_1_8_V quirk as sdhci-omap now supports UHS modes.
Signed-off-by: NKishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The data manual of J6/J6 Eco recommends to set different IODELAY values
depending on the mode in which the MMC/SD is enumerated in order to
ensure IO timings are met.

Add support to set the IODELAY values depending on the various MMC
modes using the pinctrl APIs.
Signed-off-by: NKishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Errata i802 in AM572x Sitara Processors Silicon Revision 2.0, 1.1
(SPRZ429K July 2014–Revised March 2017 [1]) mentions
DCRC error interrupts (MMCHS_STAT[21] DCRC=0x1) can occur
during the tuning procedure and it has to be disabled during the
tuning procedure Implement workaround for Errata i802 here..

[1] -> http://www.ti.com/lit/er/sprz429k/sprz429k.pdfSigned-off-by: NKishon Vijay Abraham I <kishon@ti.com>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

MMC tuning procedure is required to support SD card
UHS1-SDR104 mode and EMMC HS200 mode.

SDR104/HS200 DLL Tuning Procedure for AM572x platform is mentioned
in Figure 25-51. SDR104/HS200 DLL Tuning Procedure of
AM572x Sitara Processors Silicon Revision 2.0, 1.1 TRM
(SPRUHZ6I - October 2014–Revised April 2017 [1]).

The tuning function sdhci_omap_execute_tuning() will only be
called by the MMC/SD core if the corresponding speed modes
are supported by the OMAP silicon which is set in the mmc
host "caps" field.

[1] -> http://www.ti.com/lit/ug/spruhz6i/spruhz6i.pdfSigned-off-by: NKishon Vijay Abraham I <kishon@ti.com>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

UHS-1 DDR50 and MMC DDR52 mode require DDR bit to be
set in the configuration register (MMCHS_CON). Add
sdhci-omap specific set_uhs_signaling ops to set
this bit. Also while setting the UHSMS bit, clock should be
disabled.
Signed-off-by: NKishon Vijay Abraham I <kishon@ti.com>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Add card_busy host ops in sdhci_omap to check card busy status.

The voltage switching sequence for AM572x platform is mentioned
in Figure 25-48. eMMC/SD/SDIO Power Switching Procedure of
AM572x Sitara Processors Silicon Revision 2.0, 1.1 TRM
(SPRUHZ6I - October 2014–Revised April 2017 [1]).

In the voltage switching sequence, CLKEXTFREE bit in MMCHS_CON
should also be set after switching to 1.8v which is also taken
care in the card_busy ops.

[1] -> http://www.ti.com/lit/ug/spruhz6i/spruhz6i.pdfSigned-off-by: NKishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Updating 'power_mode' in sdhci_omap_init_74_clocks results in
'power_mode' never updated to MMC_POWER_OFF during card
removal. This results in initialization sequence not sent to the
card during re-insertion.
Fix it here by adding sdhci_omap_set_power_mode to update power_mode.
This function can also be used later to perform operations that
are specific to a power mode (e.g, disable tuning during power off).
Signed-off-by: NKishon Vijay Abraham I <kishon@ti.com>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

cat /sys/kernel/debug/mmc0/regs will hang up the system since
it's in runtime suspended state, so the genpd and biu_clk is
off. This patch fixes this problem by calling pm_runtime_get_sync
to wake it up before reading the registers.

Fixes: e9ed8835 ("mmc: dw_mmc: add runtime PM callback")
Cc: <stable@vger.kernel.org>
Signed-off-by: NShawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Add num_caps field for dw_mci_drv_data to validate the controller
id from DT alias and non-DT ways.
Reported-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NShawn Lin <shawn.lin@rock-chips.com>
Fixes: 800d78bf ("mmc: dw_mmc: add support for implementation specific callbacks")
Cc: <stable@vger.kernel.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Factor out dw_mci_init_slot_caps to consolidate parsing
all differents types of capabilities from host contrllers.
No functional change intended.
Signed-off-by: NShawn Lin <shawn.lin@rock-chips.com>
Fixes: 800d78bf ("mmc: dw_mmc: add support for implementation specific callbacks")
Cc: <stable@vger.kernel.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The hs_timing_cfg[] array is indexed using a value derived from the
"mshcN" alias in DT, which may lead to an out-of-bounds access.

Fix this by adding a range check.

Fixes: 361c7fe9 ("mmc: dw_mmc-k3: add sd support for hi3660")
Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: NShawn Lin <shawn.lin@rock-chips.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Tuning can leave the IP in an active state (Buffer Read Enable bit set)
which prevents the entry to low power states (i.e. S0i3). Data reset will
clear it.

Generally tuning is followed by a data transfer which will anyway sort out
the state, so it is rare that S0i3 is actually prevented.
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The optional DT parameter max-frequency could init the max bus frequency.
So take care of this, before setting the max bus frequency.

Fixes: 660fc733 ("mmc: bcm2835: Add new driver for the sdhost controller.")
Signed-off-by: NPhil Elwell <phil@raspberrypi.org>
Signed-off-by: NStefan Wahren <stefan.wahren@i2se.com>
Cc: <stable@vger.kernel.org> # 4.12+
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

This reverts commit 0a446976.

This commit was initially intended to fix problems with hs200 and hs400
on some boards, mainly the odroid-c2. The OC2 (Rev 0.2) I have performs
well in this modes, so I could not confirm these issues.

We've had several reports about the issues being still present on (some)
OC2, so apparently, this change does not do what it was supposed to do.
Maybe the eMMC signal quality is on the edge on the board. This may
explain the variability we see in term of stability, but this is just a
guess. Lowering the max_frequency to 100Mhz seems to do trick for those
affected by the issue

Worse, the commit created new issues (CRC errors and hangs) on other
boards, such as the kvim 1 and 2, the p200 or the libretech-cc.

According to amlogic, the Tx phase should not be tuned and left in its
default configuration, so it is best to just revert the commit.

Fixes: 0a446976 ("mmc: meson-gx: include tx phase in the tuning process")
Cc: <stable@vger.kernel.org> # 4.14+
Signed-off-by: NJerome Brunet <jbrunet@baylibre.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The Meson GX MMC driver fails to build after commit 23c35f48
("pinctrl: remove include file from <linux/device.h>") because it relies
on the pinctrl/consumer.h being pulled in by the device.h header
implicitly.

Include the header explicitly to avoid the build failure.

Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: NThierry Reding <treding@nvidia.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Blank help texts are probably either a typo, a Kconfig misunderstanding,
or some kind of half-committing to adding a help text (in which case a
TODO comment would be clearer, if the help text really can't be added
right away).

Best to remove them, IMO.
Signed-off-by: NUlf Magnusson <ulfalizer@gmail.com>
Acked-by: NRandy Dunlap <rdunlap@infradead.org>
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>

If NO_DMA=y:

    ERROR: "bad_dma_ops" [drivers/mmc/host/renesas_sdhi_sys_dmac.ko] undefined!
    ERROR: "bad_dma_ops" [drivers/mmc/host/renesas_sdhi_internal_dmac.ko] undefined!

Add dependencies on HAS_DMA to fix this.

Fixes: e578afab ("mmc: renesas_sdhi: remove wrong depends on to enable compile test")
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The bounce buffer is gone from the MMC core, and now we found out
that there are some (crippled) i.MX boards out there that have broken
ADMA (cannot do scatter-gather), and also broken PIO so they must
use SDMA. Closer examination shows a less significant slowdown
also on SDMA-only capable Laptop hosts.

SDMA sets down the number of segments to one, so that each segment
gets turned into a singular request that ping-pongs to the block
layer before the next request/segment is issued.

Apparently it happens a lot that the block layer send requests
that include a lot of physically discontiguous segments. My guess
is that this phenomenon is coming from the file system.

These devices that cannot handle scatterlists in hardware can see
major benefits from a DMA-contiguous bounce buffer.

This patch accumulates those fragmented scatterlists in a physically
contiguous bounce buffer so that we can issue bigger DMA data chunks
to/from the card.

When tested with a PCI-integrated host (1217:8221) that
only supports SDMA:
0b:00.0 SD Host controller: O2 Micro, Inc. OZ600FJ0/OZ900FJ0/OZ600FJS
        SD/MMC Card Reader Controller (rev 05)
This patch gave ~1Mbyte/s improved throughput on large reads and
writes when testing using iozone than without the patch.

dmesg:
sdhci-pci 0000:0b:00.0: SDHCI controller found [1217:8221] (rev 5)
mmc0 bounce up to 128 segments into one, max segment size 65536 bytes
mmc0: SDHCI controller on PCI [0000:0b:00.0] using DMA

On the i.MX SDHCI controllers on the crippled i.MX 25 and i.MX 35
the patch restores the performance to what it was before we removed
the bounce buffers.

Cc: Pierre Ossman <pierre@ossman.eu>
Cc: Benoît Thébaudeau <benoit@wsystem.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Benjamin Beckmeyer <beckmeyer.b@rittal.de>
Cc: stable@vger.kernel.org # v4.14+
Fixes: de3ee99b ("mmc: Delete bounce buffer handling")
Tested-by: NBenjamin Beckmeyer <beckmeyer.b@rittal.de>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.

Fixes: f9bb304c ("mmc: mmci: Add support for setting pad type via pinctrl")
Signed-off-by: NWei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: NPatrice Chotard <patrice.chotard@st.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

This suppresses printing an error message during probe of the TI DaVinci
MMC driver when the error is EPROBE_DEFER.
Signed-off-by: NDavid Lechner <david@lechnology.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

This changes module_platform_driver_probe() to module_platform_driver()
in the TI DaVinci MMC driver.

On device tree systems, we can get a -EPROBE_DEFER when using a pinmux
for the CD GPIO, which results in the driver never loading because
module_platform_driver_probe() prevents it from being re-probed.

So, we replace module_platform_driver_probe() with
module_platform_driver() and removed the __init attributes accordingly.
Signed-off-by: NDavid Lechner <david@lechnology.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

When CONFIG_PM is disabled, we get a warning about the clock handling
being unused:

drivers/mmc/host/tmio_mmc_core.c:937:13: error: 'tmio_mmc_clk_disable' defined but not used [-Werror=unused-function]
 static void tmio_mmc_clk_disable(struct tmio_mmc_host *host)
             ^~~~~~~~~~~~~~~~~~~~
drivers/mmc/host/tmio_mmc_core.c:929:12: error: 'tmio_mmc_clk_enable' defined but not used [-Werror=unused-function]
 static int tmio_mmc_clk_enable(struct tmio_mmc_host *host)
            ^~~~~~~~~~~~~~~~~~~

As the clock handling is now done elsewhere, this is only used when
power management is enabled. We could make the functions as __maybe_unused,
but since there is already an #ifdef section, it seems easier to move
the helpers closer to their callers.

Fixes: b21fc294 ("mmc: tmio: move clk_enable/disable out of tmio_mmc_host_probe()")
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Reviewed-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

STM32F4 and STM32F7 MCUs has a SDIO controller that looks like
an ARM PL810.
This patch adds the STM32 variant so that mmci driver supports it.
Signed-off-by: NAndrea Merello <andrea.merello@gmail.com>
Signed-off-by: NPatrice Chotard <patrice.chotard@st.com>
Reviewed-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

If variant hasn't the control bit to switch pads in opendrain mode,
we can achieve the same result by asking to the pinmux driver to
configure pins for us.

This patch make the mmci driver able to do this whenever needed.
Signed-off-by: NAndrea Merello <andrea.merello@gmail.com>
Signed-off-by: NPatrice Chotard <patrice.chotard@st.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

This patch prepares for supporting STM32 variant which doesn't
have opendrain bit in MMCIPOWER register.
ST others variant (u300, nomadik and ux500) uses MCI_OD bit whereas
others variants uses MCI_ROD bit.
Signed-off-by: NPatrice Chotard <patrice.chotard@st.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

This patch prepares for supporting the STM32 variant that
has no such bit in the status register.
Signed-off-by: NAndrea Merello <andrea.merello@gmail.com>
Signed-off-by: NPatrice Chotard <patrice.chotard@st.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Two mask registers are used in order to select which events have to
actually generate an interrupt on each IRQ line.

It seems that in the single-IRQ case it's assumed that the IRQs lines
are simply OR-ed, while the two mask registers are still present. The
driver still programs the two mask registers separately.

However the STM32 variant has only one IRQ, and also has only one mask
register.

This patch prepares for STM32 variant support by making the driver using
only one mask register.

This patch also optimize the MMCIMASK1 mask usage by caching it into
host->mask1_reg which avoid to read it into mmci_irq().

Tested only on STM32 variant. RFT for variants other than STM32
Signed-off-by: NAndrea Merello <andrea.merello@gmail.com>
Signed-off-by: NPatrice Chotard <patrice.chotard@st.com>
Reviewed-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

This IP provides the write protect signal level in the status
register, but it is also possible to use GPIO for WP.  They are
exclusive, so it is not efficient to call mmc_gpio_get_ro() every
time from tmio_mmc_get_ro() if we know gpio_ro is not used.

Check the capability of gpio_ro just once in the probe function,
then set mmc_gpio_get_ro to .get_ro if it is the case.
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Drivers need to set up various struct members for tmio_mmc_host before
calling tmio_mmc_host_probe().  Do likewise for host->dma_ops instead
of passing it as a function argument.
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

mmc_of_parse() parses various DT properties and sets capability flags
accordingly.  However, drivers have no chance to run platform init
code depending on such flags because mmc_of_parse() is called from
tmio_mmc_host_probe().

Move mmc_of_parse() to tmio_mmc_host_alloc() so that drivers can
handle capabilities before mmc_add_host().  Move tmio_mmc_of_parse()
likewise.
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>