This patch adds a common clock driver for Silicon Labs Si5351a/b/c
i2c programmable clock generators. Currently, the driver does not
support VXCO feature of si5351b. Passing platform_data or DT bindings
selectively allows to overwrite stored Si5351 configuration which is
very helpful for clock generators with empty eeprom configuration.
Corresponding device tree binding documentation is also added.
Signed-off-by: NSebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-by: NDaniel Mack <zonque@gmail.com>
Acked-by: NGuenter Roeck <linux@roeck-us.net>
Tested-by: NMichal Bachraty <michal.bachraty@streamunlimited.com>
Signed-off-by: NMike Turquette <mturquette@linaro.org>

This driver adds support for the AXI clkgen pcore to the common clock framework.
The AXI clkgen pcore is a AXI front-end to the MMCM_ADV frequency synthesizer
commonly found in Xilinx FPGAs.

The AXI clkgen pcore is used in Analog Devices' reference designs targeting
Xilinx FPGAs.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Signed-off-by: NMike Turquette <mturquette@linaro.org>

This driver allows to provide DT clocks for core clocks found on
Marvell Kirkwood, Dove & 370/XP SoCs. The core clock frequencies and
ratios are determined by decoding the Sample-At-Reset registers.

Although technically correct, using a divider of 0 will lead to
div_by_zero panic. Let's use a ratio of 0/1 instead to fail later
with a zero clock.
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: NSebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Tested-by Gregory CLEMENT <gregory.clement@free-electrons.com>

This patch adds a DT and non-DT based implementation of
the common clock infrastructure for Versatile Express
platform. It registers (statically or using DT) all
required fixed clocks, initialises motherboard's SP810
cell (that provides clocks for SP804 timers) and
explicitly registers VE "osc" driver, to make the
clock generators available early.
Signed-off-by: NPawel Moll <pawel.moll@arm.com>
Signed-off-by: NMike Turquette <mturquette@linaro.org>

On OMAP4+ platforms the functional clock for the McPDM IP is suplied by
the twl6040 codec (bit clock on the PDM bus).
This common clock driver for twl6040 will register the mcpdm_fclk clock to
be used by the McPDM driver to make sure that the needed clocks are
available when needed.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NMike Turquette <mturquette@linaro.org>

This patch supports max77686 mfd's clock driver using common clock frame work.
max77686 has 3 clock ouputs which all are generated from crystal oscillator and
SOC can enable/disable them via I2C bus. All clocks are fixed-rate clock sources
so that it doesn't supply interface for changing clock rate.
Driver uses regmap API to communicate with internal register.
Signed-off-by: NJonghwa Lee <jonghwa3.lee@samsung.com>
Signed-off-by: NMike Turquette <mturquette@linaro.org>

There is no choice to have the RealView clocks as module for sure,
so turn this config option into a boolean.
Reported-by: NPawel Moll <pawel.moll@arm.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NMike Turquette <mturquette@linaro.org>

This converts the ARM RealView machine over to using the common
clock. The approach is similar to the one used for the Integrator,
and we're reusing the ICST wrapper code.

We have to put the clock intialization in the timer init function
for the clocks to be available when initializing the timer,
keeping them in early_init() is too early for the common clk.

Since we now have to go down and compile drivers/clk/versatile
a CONFIG_COMMON_CLK_VERSATILE symbol has been added so the proper
code gets compiled into the kernel for either machine. A leftover
CLK_VERSATILE in the Integrator Kconfig was fixed up to use
the new symbol as well.

Tested on ARM RealView PB1176.

Cc: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NMike Turquette <mturquette@linaro.org>

menu "Common Clock Framework" has "depends on COMMON_CLK" and so configs
defined within menu don't require these "depends on COMMON_CLK again".
Signed-off-by: NViresh Kumar <viresh.kumar@st.com>
Cc: Wolfram Sang <w.sang@pengutronix.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jeff Garzik <jgarzik@redhat.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Bhupesh Sharma <bhupesh.sharma@st.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Mike Turquette <mturquette@linaro.org>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: viresh kumar <viresh.linux@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The WM831x and WM832x series of PMICs contain a flexible clocking
subsystem intended to provide always on and system core clocks.  It
features:

- A 32.768kHz crystal oscillator which can optionally be used to pass
  through an externally generated clock.
- A FLL which can be clocked from either the 32.768kHz oscillator or
  the CLKIN pin.
- A CLKOUT pin which can bring out either the oscillator or the FLL
  output.
- The 32.768kHz clock can also optionally be brought out on the GPIO
  pins of the device.

This driver fully supports the 32.768kHz oscillator and CLKOUT.  The FLL
is supported only in AUTO mode, the full flexibility of the FLL cannot
currently be used.

Due to a lack of access to systems where the core SoC has been converted
to use the generic clock API this driver has been compile tested only.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NMike Turquette <mturquette@linaro.org>

Exposing this option generates confusion and incorrect behavior for
single-image builds across platforms.  Enable this behavior permanently.
Signed-off-by: NMike Turquette <mturquette@linaro.org>
Acked-by: NSaravana Kannan <skannan@codeaurora.org>

Using the common clock infrastructure without the common clkdev code makes
little sense, so select CLKDEV_LOOKUP for COMMON_CLK.
Signed-off-by: NRob Herring <rob.herring@calxeda.com>

All platforms that use the common clk infrastructure should select
COMMON_CLK from platform code, and on all other platforms, it must
not be enabled, so there is no point making the option visible to
users, and when it is visible, we break randconfig builds.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

The common clock framework defines a common struct clk useful across
most platforms as well as an implementation of the clk api that drivers
can use safely for managing clocks.

The net result is consolidation of many different struct clk definitions
and platform-specific clock framework implementations.

This patch introduces the common struct clk, struct clk_ops and an
implementation of the well-known clock api in include/clk/clk.h.
Platforms may define their own hardware-specific clock structure and
their own clock operation callbacks, so long as it wraps an instance of
struct clk_hw.

See Documentation/clk.txt for more details.

This patch is based on the work of Jeremy Kerr, which in turn was based
on the work of Ben Herrenschmidt.
Signed-off-by: NMike Turquette <mturquette@linaro.org>
Signed-off-by: NMike Turquette <mturquette@ti.com>
Reviewed-by: NThomas Gleixner <tglx@linutronix.de>
Tested-by: NAndrew Lunn <andrew@lunn.ch>
Reviewed-by: Rob Herring <rob.herring <at> calxeda.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Jeremy Kerr <jeremy.kerr@canonical.com>
Cc: Arnd Bergman <arnd.bergmann@linaro.org>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Shawn Guo <shawn.guo@freescale.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Richard Zhao <richard.zhao@linaro.org>
Cc: Saravana Kannan <skannan@codeaurora.org>
Cc: Magnus Damm <magnus.damm@gmail.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Linus Walleij <linus.walleij@stericsson.com>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Amit Kucheria <amit.kucheria@linaro.org>
Cc: Deepak Saxena <dsaxena@linaro.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

The commit 40d3e0f4 (clk: provide prepare/unprepare functions) provides
the config option HAVE_CLK_PREPARE for platforms that have
prepare/unprepare implementation to select.  This patch adds the option
into drivers/clk/Kconfig, so that it can be actually selected.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>

Now most of ARM machines has the alsmot same __clk_get/put() macro

So place it at the arch/arm/include/asm/clkdev.h and remove the reduntant header files

But some machines don't have the same form as above. It can use the machince specific clkdev file by HAVE_MACH_CLKDEV config

Now there are only 3 caese.

1) define the clk structure with clkdev macro => Need to move clk structure to proper header file

arch/arm/mach-versatile/include/mach/clkdev.h
arch/arm/mach-realview/include/mach/clkdev.h
arch/arm/mach-vexpress/include/mach/clkdev.h
arch/arm/mach-integrator/include/mach/clkdev.h

2) export the __clk_get/put function at clock.c

arch/arm/mach-shmobile/include/mach/clkdev.h

3) demuxing the clk source
arch/arm/mach-u300/include/mach/clkdev.h
Acked-by: NViresh Kumar <viresh.kumar@st.com>
Acked-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>

factorise some generic infrastructure to assist looking up struct clks
for the ARM & SH architecture.

as the code is identical at 99%

put the arch specific code for allocation as example in asm/clkdev.h
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: NPaul Mundt <lethal@linux-sh.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>