We can't forward declare enums.
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Clean up interrupts on exit, silencing a sparse warning caused by
tps65912_irq_exit() being defined but not prototyped as we go.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Currently driver sets the irq type to IRQF_TRIGGER_LOW which is
causing interrupt registration failure in ARM based SoCs as:
[    0.208479] genirq: Setting trigger mode 8 for irq 118 failed (gic_set_type+0x0/0xf0)
[    0.208513] dummy 0-0059: Failed to request IRQ 118: -22

Provide the irq flags through platform data if device is registered
through board file or get the irq type from DT node property in place
of hardcoding the irq flag in driver to support multiple platforms.

Also configure the device to generate the interrupt signal according to
flag type.
Signed-off-by: NLaxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

TI LP8788 PMU supports regulators, battery charger, RTC, ADC, backlight
dri= ver and current sinks.  This patch enables LP8788 backlight module.

(Brightness mode)
The brightness is controlled by PWM input or I2C register.
All modes are supported in the driver.

(Platform data)
Configurable data can be defined in the platform side.
 name                  : backlight driver name. (default: "lcd-backlight")
 initial_brightness    : initial value of backlight brightness
 bl_mode               : brightness control by PWM or lp8788 register
 dim_mode              : dimming mode selection
 full_scale            : full scale current setting
 rise_time             : brightness ramp up step time
 fall_time             : brightness ramp down step time
 pwm_pol               : PWM polarity setting when bl_mode is PWM based
 period_ns             : platform specific PWM period value. unit is nano.

The default values are set in case no platform data is defined.

[akpm@linux-foundation.org: checkpatch fixes]
Signed-off-by: NMilo(Woogyom) Kim <milo.kim@ti.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Thierry Reding <thierry.reding@avionic-design.de>
Cc: "devendra.aaru" <devendra.aaru@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The tmio_mmc_cd_wakeup() inline function has been deprecated since 3.4 and
is unused since 3.4 too. Remove them.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NChris Ball <cjb@laptop.org>

Realtek card reader supports both SD and MS card. According to the
settings of rtsx MFD driver, SD host will be probed before MS host.
If we boot/reboot Linux with SD card inserted, the resetting flow of SD
card will succeed, and the following resetting flow of MS is sure to fail.
Then MS upper-level driver will ask rtsx driver to turn power off. This
request leads to the result that the following SD commands fail and SD card
can't be accessed again.

In this commit, Realtek's SD and MS host driver will check whether the card
that upper driver requesting is the one existing in the slot. If not, Realtek's
host driver will refuse the operation to make sure the exlusive accessing
at the same time.
Signed-off-by: NWei WANG <wei_wang@realsil.com.cn>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Add irqdomains for max8925's main irq, wrap irq register operations
into irqdomain's map func. it is necessary for dt support.

Also, add dt support for max8925 driver.
Signed-off-by: NQing Xu <qingx@marvell.com>
Signed-off-by: NHaojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Support new model RTS5227.
Signed-off-by: NRoger Tseng <rogerable@realtek.com>
Reviewed-by: NWei WANG <wei_wang@realsil.com.cn>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Fix a misspelling word in comment
Signed-off-by: NWei WANG <wei_wang@realsil.com.cn>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

devm_* functions are device managed and make error handling
and code simpler; it also fix error exit paths
Signed-off-by: NYi Zhang <yizhang@marvell.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Add definition of watchdog IDs to be used by ux500_wdt driver.
Acked-by: NLee Jones <lee.jones@linaro.org>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NFabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Allow the MICBIAS voltages and other attributes to be configured by the
platform.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Palmas register set is divided into different blocks (base and offset)
and hence different i2c addresses. The i2c address offsets are derived
from base address of block of registers.

Add inline APIs to access the Palma's registers which takes the base of
register block and register offset. The i2c address offset is  derived
from the base address of register blocks.
Signed-off-by: NLaxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

This patch use delayed workqueue to check cable state after a certain
time. If extcon-max8997 driver check cable state during booting of
platform, this couldn't send the correct notification of cable state
to extcon consumer. Alwasys, this driver should check cable state
after the completion of platform initialization
Signed-off-by: NChanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: NMyungjoo Ham <myungjoo.ham@samsung.com>

This patch set default H/W line path according to platfomr data.
The MAX8997 MUIC device can possibly set UART/USB or UART_AUX
/USB_AUX to internal H/W line path of MUIC device. Namely, only
one H/W line is used for two operation.

For example,
if H/W line path of MAX8997 device set UART/USB, micro usb cable
is connected to AP(Application Processor) and if H/W line path
set UART_AUX/USB_AUX, micro usb cable is connected to CP(Coprocessor).
Signed-off-by: NChanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: NMyungjoo Ham <myungjoo.ham@samsung.com>

This patch make max8997_muic_get_cable_type() function to remove
duplicate code for checking ADC/Charger cable type because almost
internal function need to read adc/chg_type value of MUIC register.

Also, remove *_detach() function, extcon-max8997 driver treat
attach/detach operation of cable in max8997_*_handler() function.
Lastly, this patch move defined constant in header file(include/
linux/mfd/max8997.h, max8997-private.h) because defined constant
is only used in the 'extcon-max8997.c'.
Signed-off-by: NChanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: NMyungjoo Ham <myungjoo.ham@samsung.com>

This patch set default of ADC Debounce Time(25ms) during probe step.
Also, can possible change ADC Debounce Time according to H/W situation
by using max8997_set_adc_debounce_time()
Signed-off-by: NChanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: NMyungjoo Ham <myungjoo.ham@samsung.com>

Signed-off-by: NChanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: NMyungjoo Ham <myungjoo.ham@samsung.com>

This patch move defined constants to header file(max77693-private.h)
because of mask/unmask selectively interrupt of MUIC device according
to attribute of H/W board.
Signed-off-by: NChanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: NMyungjoo Ham <myungjoo.ham@samsung.com>

When trying to get rid of the cross-includes of <mach/id.h>
from different drivers, so we can localize ASIC/CPU detection
to the mach-ux500 folder, we run into the way the PRCMU
handles base addresses and firmware detection.

This patch updates the firmware version detection to pass
the required information as platform data instead of
relying on cpu_is_* macros.

Now the PRCMU base address, the secondary TCDM area, the
TCPM area and the IRQ are passed as resources instead of
being grabbed from <mach/*> files. Incidentally this also
removes part of the reliance on <mach/irqs.h>.

Further it updates the firmware version detection, since the
location of the firmware ID bytes in the designated memory
are is now passed from the platform data instead. There is
no reason not to include the nice split-off of a struct to
hold the firmware information and a separate function to
populate it.

The patch actually rids the need to use the external
db8500_prcmu_early_init call at all, but I'm keepin back
that removal as I don't want the patch to be too big.

Cc: arm@kernel.org
Cc: Michel Jaoen <michel.jaouen@stericsson.com>
Cc: Lee Jones <lee.jones@linaro.org>
Acked-by: NSamuel Ortiz <sameo@linux.intel.com>
Acked-by: NLoic Pallardy <loic.pallardy@stericsson.com>
Acked-by: NFabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

It is important to clear the wake trigger status bits otherwise DCVDD
will be held high independent of the state of the LDOENA line.
Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

AB8500 GPIO no longer handles its GPIO IRQs. Instead, the AB8500
core driver has taken back the responsibility. Prior to this
happening, the AB8500 GPIO driver provided a set of virtual IRQs
which were used as a pass-through. These virtual IRQs had a base
of MOP500_AB8500_VIR_GPIO_IRQ_BASE, which was passed though pdata.
We don't need to do this anymore, so we're pulling out the
property from the structure.

Cc: arm@kernel.org
Acked-by: NOlof Johansson <olof@lixom.net>
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

When starting microphone detection some headsets should be exposed to
the fully regulated microphone bias in order to ensure that they behave
in an optimal fashion.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Allow systems to tune detection rate and debounce suitably for their
mechanical parameters.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

This device tree support is added for PMIC block of S5m8767 multi
function driver. The usage detail is added in the device tree
documentation section. This change is tested on exynos5250 based
arndale platform by regulator voltage set/get API's.
Reviewed-by: NThomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: NAmit Daniel Kachhap <amit.daniel@samsung.com>
Tested-by: NSachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

This patch adds an entry in debugfs to check number of interrupts
from the AB.
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NBengt Jonsson <bengt.g.jonsson@stericsson.com>
Reviewed-by: NRabin VINCENT <rabin.vincent@stericsson.com>

Implement an API so that a user may dump all AB8500 registers
via debugfs file access.
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NMian Yousaf Kaukab <mian.yousaf.kaukab@stericsson.com>
Reviewed-by: NLinus WALLEIJ <linus.walleij@stericsson.com>
Reviewed-by: NJonas ABERG <jonas.aberg@stericsson.com>

Some drivers can detect subsystem failures e.g. shared memory driver
can detect modem sub system failures. It would be helpful in analyzing
these failures if AB register dump is available at that point. This
patch adds the API for the drivers to dump AB registers in the kernel
log.
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NMian Yousaf Kaukab <mian.yousaf.kaukab@stericsson.com>
Reviewed-by: NLinus WALLEIJ <linus.walleij@stericsson.com>
Reviewed-by: NJonas ABERG <jonas.aberg@stericsson.com>

Add the possibility to pass configuration settings for
SysCl1kReqRfClkBuf to SysClk8ReqRfClkBuf via platform data.
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NKennet Wallden <kennet.wallden@stericsson.com>
Reviewed-by: NKarl-Johan PERNTZ <karl-johan.perntz@stericsson.com>
Reviewed-by: NBengt JONSSON <bengt.g.jonsson@stericsson.com>

The kernel allows us to specify a function call-back which will be
invoked when a system power-off request has been received. Here we
provide one which is to be used when shutting down AB8500 based
platforms.
Signed-off-by: NLee Jones <lee.jones@linaro.org>

This adds the AB8500 core driver, which will be utilized by
the follow-on drivers for different ABx500 variants.
Sselect the driver from the DBX500_SOC, as this chip is
powering and clocking that SoC.

Cc: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: NPatrice Chotard <patrice.chotard@st.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This updates the AB8500 register map with defines for a few
new chip variants and adds version detection helpers to handle
the different variants.
Acked-by: NSamuel Ortiz <sameo@linux.intel.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This removes the file <mach/id.h> from the global kernel include
scope, making it a pure mach-ux500 detail. All ASIC specifics
needed by drivers shall henceforth be passed from either platform
data or the device tree.

Cc: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: NSamuel Ortiz <sameo@linux.intel.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

These static inlines are duplicating the task now done by the
Nomadik pinctrl drivers, so delete them from the prcmu static
inlines, also delete the register definitions as these should
only be known by the pinctrl driver.

Cc: Loic Pallardy <loic.pallardy@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Michel Jaouen <michel.jaouen@st.com>
Acked-by: NSamuel Ortiz <sameo@linux.intel.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

An issue has been reported where the PMIC either locks up or fails to
respond following a system Reset. This could result in a second write
in which the bus writes the current content of the write buffer to address
of the last I2C access.

The failure case is where this unwanted write transfers incorrect data to
a critical register.

This patch fixes this issue to by following any read or write with a dummy read
to a safe register address. A safe register address is one where the contents
will not affect the operation of the system.
Signed-off-by: NAshish Jangam <ashish.jangam@kpitcummins.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Add callback function conv_clk_and_div_n to convert between SSC clock
and its divider N.
For rtl8411, the formula to calculate SSC clock divider N is different
with the other card reader models.
Signed-off-by: NWei WANG <wei_wang@realsil.com.cn>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Different card reader has different method to switch output voltage,
add this callback to let the card reader implement its individual switch
function.
This is needed as rtl8411 has a specific switch output voltage procedure.
Signed-off-by: NWei WANG <wei_wang@realsil.com.cn>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

None of the aforementioned components have their own dedicated
platform data structures anymore. Instead they have all been
merged into one big Battery Management container. Let's remove
them and place all the nice newly added attributes into the core
container.
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Do not touch the VBUSOVV in USBCHTRL2 when running on AB8505.
Signed-off-by: NJonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Reviewed-by: NMarcus COOPER <marcus.xm.cooper@stericsson.com>
Tested-by: NMian Yousaf KAUKAB <mian.yousaf.kaukab@stericsson.com>