pinctrl: add abx500 pinctrl driver core

This adds the AB8500 core driver, which will be utilized by
the follow-on drivers for different ABx500 variants.
Sselect the driver from the DBX500_SOC, as this chip is
powering and clocking that SoC.

Cc: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: NPatrice Chotard <patrice.chotard@st.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

arch/arm/mach-ux500/Kconfig

@@ -11,6 +11,7 @@ config UX500_SOC_COMMON
 	select COMMON_CLK
 	select PINCTRL
 	select PINCTRL_NOMADIK
+	select PINCTRL_ABX500
 	select PL310_ERRATA_753970 if CACHE_PL310
 
 config UX500_SOC_DB8500

arch/arm/mach-ux500/board-mop500.c

@@ -90,26 +90,9 @@ static struct platform_device snowball_gpio_en_3v3_regulator_dev = {
        },
 };
 
-static struct ab8500_gpio_platform_data ab8500_gpio_pdata = {
+static struct abx500_gpio_platform_data ab8500_gpio_pdata = {
 	.gpio_base		= MOP500_AB8500_PIN_GPIO(1),
 	.irq_base		= MOP500_AB8500_VIR_GPIO_IRQ_BASE,
-	/* config_reg is the initial configuration of ab8500 pins.
-	 * The pins can be configured as GPIO or alt functions based
-	 * on value present in GpioSel1 to GpioSel6 and AlternatFunction
-	 * register. This is the array of 7 configuration settings.
-	 * One has to compile time decide these settings. Below is the
-	 * explanation of these setting
-	 * GpioSel1 = 0x00 => Pins GPIO1 to GPIO8 are not used as GPIO
-	 * GpioSel2 = 0x1E => Pins GPIO10 to GPIO13 are configured as GPIO
-	 * GpioSel3 = 0x80 => Pin GPIO24 is configured as GPIO
-	 * GpioSel4 = 0x01 => Pin GPIo25 is configured as GPIO
-	 * GpioSel5 = 0x7A => Pins GPIO34, GPIO36 to GPIO39 are conf as GPIO
-	 * GpioSel6 = 0x00 => Pins GPIO41 & GPIo42 are not configured as GPIO
-	 * AlternaFunction = 0x00 => If Pins GPIO10 to 13 are not configured
-	 * as GPIO then this register selectes the alternate fucntions
-	 */
-	.config_reg		= {0x00, 0x1E, 0x80, 0x01,
-					0x7A, 0x00, 0x00},
 };
 
 /* ab8500-codec */

drivers/pinctrl/Kconfig

@@ -26,6 +26,13 @@ config DEBUG_PINCTRL
 	help
 	  Say Y here to add some extra checks and diagnostics to PINCTRL calls.
 
+config PINCTRL_ABX500
+	bool "ST-Ericsson ABx500 family Mixed Signal Circuit gpio functions"
+	depends on AB8500_CORE
+	select GENERIC_PINCONF
+	help
+	  Select this to enable the ABx500 family IC GPIO driver
+
 config PINCTRL_AT91
 	bool "AT91 pinctrl driver"
 	depends on OF

drivers/pinctrl/Makefile

@@ -9,6 +9,7 @@ ifeq ($(CONFIG_OF),y)
 obj-$(CONFIG_PINCTRL)		+= devicetree.o
 endif
 obj-$(CONFIG_GENERIC_PINCONF)	+= pinconf-generic.o
+obj-$(CONFIG_PINCTRL_ABX500)	+= pinctrl-abx500.o
 obj-$(CONFIG_PINCTRL_AT91)	+= pinctrl-at91.o
 obj-$(CONFIG_PINCTRL_BCM2835)	+= pinctrl-bcm2835.o
 obj-$(CONFIG_PINCTRL_IMX)	+= pinctrl-imx.o

drivers/pinctrl/pinctrl-abx500.h

+#ifndef PINCTRL_PINCTRL_ABx5O0_H
+#define PINCTRL_PINCTRL_ABx500_H
+
+/* Package definitions */
+#define PINCTRL_AB8500	0
+#define PINCTRL_AB8540	1
+#define PINCTRL_AB9540	2
+#define PINCTRL_AB8505	3
+
+/* pins alternate function */
+enum abx500_pin_func {
+	ABX500_DEFAULT,
+	ABX500_ALT_A,
+	ABX500_ALT_B,
+	ABX500_ALT_C,
+};
+
+/**
+ * struct abx500_function - ABx500 pinctrl mux function
+ * @name: The name of the function, exported to pinctrl core.
+ * @groups: An array of pin groups that may select this function.
+ * @ngroups: The number of entries in @groups.
+ */
+struct abx500_function {
+	const char *name;
+	const char * const *groups;
+	unsigned ngroups;
+};
+
+/**
+ * struct abx500_pingroup - describes a ABx500 pin group
+ * @name: the name of this specific pin group
+ * @pins: an array of discrete physical pins used in this group, taken
+ *	from the driver-local pin enumeration space
+ * @num_pins: the number of pins in this group array, i.e. the number of
+ *	elements in .pins so we can iterate over that array
+ * @altsetting: the altsetting to apply to all pins in this group to
+ *	configure them to be used by a function
+ */
+struct abx500_pingroup {
+	const char *name;
+	const unsigned int *pins;
+	const unsigned npins;
+	int altsetting;
+};
+
+#define ALTERNATE_FUNCTIONS(pin, sel_bit, alt1, alt2, alta, altb, altc)	\
+{									\
+	.pin_number = pin,						\
+	.gpiosel_bit = sel_bit,						\
+	.alt_bit1 = alt1,						\
+	.alt_bit2 = alt2,						\
+	.alta_val = alta,						\
+	.altb_val = altb,						\
+	.altc_val = altc,						\
+}
+
+#define UNUSED -1
+/**
+ * struct alternate_functions
+ * @pin_number:		The pin number
+ * @gpiosel_bit:	Control bit in GPIOSEL register,
+ * @alt_bit1:		First AlternateFunction bit used to select the
+ *			alternate function
+ * @alt_bit2:		Second AlternateFunction bit used to select the
+ *			alternate function
+ *
+ *			these 3 following fields are necessary due to none
+ *			coherency on how to select the altA, altB and altC
+ *			function between the ABx500 SOC family when using
+ *			alternatfunc register.
+ * @alta_val:		value to write in alternatfunc to select altA function
+ * @altb_val:		value to write in alternatfunc to select altB function
+ * @altc_val:		value to write in alternatfunc to select altC function
+ */
+struct alternate_functions {
+	unsigned pin_number;
+	s8 gpiosel_bit;
+	s8 alt_bit1;
+	s8 alt_bit2;
+	u8 alta_val;
+	u8 altb_val;
+	u8 altc_val;
+};
+
+/**
+ * struct pullud - specific pull up/down feature
+ * @first_pin:		The pin number of the first pins which support
+ *			specific pull up/down
+ * @last_pin:		The pin number of the last pins
+ */
+struct pullud {
+	unsigned first_pin;
+	unsigned last_pin;
+};
+
+#define GPIO_IRQ_CLUSTER(a, b, c)	\
+{					\
+	.start = a,			\
+	.end = b,			\
+	.offset = c,			\
+}
+
+/**
+ * struct abx500_gpio_irq_cluster - indicates GPIOs which are interrupt
+ *			capable
+ * @start:		The pin number of the first pin interrupt capable
+ * @end:		The pin number of the last pin interrupt capable
+ * @offset:		offset used to compute specific setting strategy of
+ *			the interrupt line
+ */
+
+struct abx500_gpio_irq_cluster {
+	int start;
+	int end;
+	int offset;
+};
+
+/**
+ * struct abx500_pinrange - map pin numbers to GPIO offsets
+ * @offset:		offset into the GPIO local numberspace, incidentally
+ *			identical to the offset into the local pin numberspace
+ * @npins:		number of pins to map from both offsets
+ * @altfunc:		altfunc setting to be used to enable GPIO on a pin in
+ *			this range (may vary)
+ */
+struct abx500_pinrange {
+	unsigned int offset;
+	unsigned int npins;
+	int altfunc;
+};
+
+#define ABX500_PINRANGE(a, b, c) { .offset = a, .npins = b, .altfunc = c }
+
+/**
+ * struct abx500_pinctrl_soc_data - ABx500 pin controller per-SoC configuration
+ * @gpio_ranges:	An array of GPIO ranges for this SoC
+ * @gpio_num_ranges:	The number of GPIO ranges for this SoC
+ * @pins:		An array describing all pins the pin controller affects.
+ *			All pins which are also GPIOs must be listed first within the
+ *			array, and be numbered identically to the GPIO controller's
+ *			numbering.
+ * @npins:		The number of entries in @pins.
+ * @functions:		The functions supported on this SoC.
+ * @nfunction:		The number of entries in @functions.
+ * @groups:		An array describing all pin groups the pin SoC supports.
+ * @ngroups:		The number of entries in @groups.
+ * @alternate_functions: array describing pins which supports alternate and
+ *			how to set it.
+ * @pullud:		array describing pins which supports pull up/down
+ *			specific registers.
+ * @gpio_irq_cluster:	An array of GPIO interrupt capable for this SoC
+ * @ngpio_irq_cluster:	The number of GPIO inetrrupt capable for this SoC
+ * @irq_gpio_rising_offset: Interrupt offset used as base to compute specific
+ *			setting strategy of the rising interrupt line
+ * @irq_gpio_falling_offset: Interrupt offset used as base to compute specific
+ *			setting strategy of the falling interrupt line
+ * @irq_gpio_factor:	Factor used to compute specific setting strategy of
+ *			the interrupt line
+ */
+
+struct abx500_pinctrl_soc_data {
+	const struct abx500_pinrange *gpio_ranges;
+	unsigned gpio_num_ranges;
+	const struct pinctrl_pin_desc *pins;
+	unsigned npins;
+	const struct abx500_function *functions;
+	unsigned nfunctions;
+	const struct abx500_pingroup *groups;
+	unsigned ngroups;
+	struct alternate_functions *alternate_functions;
+	struct pullud *pullud;
+	struct abx500_gpio_irq_cluster *gpio_irq_cluster;
+	unsigned ngpio_irq_cluster;
+	int irq_gpio_rising_offset;
+	int irq_gpio_falling_offset;
+	int irq_gpio_factor;
+};
+
+#endif /* PINCTRL_PINCTRL_ABx500_H */

include/linux/mfd/abx500/ab8500-gpio.h

@@ -14,10 +14,21 @@
  * registers.
  */
 
-struct ab8500_gpio_platform_data {
+struct abx500_gpio_platform_data {
 	int gpio_base;
 	u32 irq_base;
-	u8  config_reg[8];
+};
+
+enum abx500_gpio_pull_updown {
+	ABX500_GPIO_PULL_DOWN = 0x0,
+	ABX500_GPIO_PULL_NONE = 0x1,
+	ABX500_GPIO_PULL_UP = 0x3,
+};
+
+enum abx500_gpio_vinsel {
+	ABX500_GPIO_VINSEL_VBAT = 0x0,
+	ABX500_GPIO_VINSEL_VIN_1V8 = 0x1,
+	ABX500_GPIO_VINSEL_VDD_BIF = 0x2,
 };
 
 #endif /* _AB8500_GPIO_H */

include/linux/mfd/abx500/ab8500.h

@@ -385,7 +385,7 @@ struct ab8500_platform_data {
 	struct ab8500_regulator_reg_init *regulator_reg_init;
 	int num_regulator;
 	struct regulator_init_data *regulator;
-	struct ab8500_gpio_platform_data *gpio;
+	struct abx500_gpio_platform_data *gpio;
 	struct ab8500_codec_platform_data *codec;
 };