Reimplement suspend/resume support using sdev->manage_start_stop.

* Device suspend/resume is now SCSI layer's responsibility and the
  code is simplified a lot.

* DPM is dropped.  This also simplifies code a lot.  Suspend/resume
  status is port-wide now.

* ata_scsi_device_suspend/resume() and ata_dev_ready() removed.

* Resume now has to wait for disk to spin up before proceeding.  I
  couldn't find easy way out as libata is in EH waiting for the
  disk to be ready and sd is waiting for EH to complete to issue
  START_STOP.

* sdev->manage_start_stop is set to 1 in ata_scsi_slave_config().
  This fixes spindown on shutdown and suspend-to-disk.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Add @deadline to prereset and reset methods and make them honor it.
ata_wait_ready() which directly takes @deadline is implemented to be
used as the wait function.  This patch is in preparation for EH timing
improvements.

* ata_wait_ready() never does busy sleep.  It's only used from EH and
  no wait in EH is that urgent.  This function also prints 'be
  patient' message automatically after 5 secs of waiting if more than
  3 secs is remaining till deadline.

* ata_bus_post_reset() now fails with error code if any of its wait
  fails.  This is important because earlier reset tries will have
  shorter timeout than the spec requires.  If a device fails to
  respond before the short timeout, reset should be retried with
  longer timeout rather than silently ignoring the device.

  There are three behavior differences.

  1. Timeout is applied to both devices at once, not separately.  This
     is more consistent with what the spec says.

  2. When a device passes devchk but fails to become ready before
     deadline.  Previouly, post_reset would just succeed and let
     device classification remove the device.  New code fails the
     reset thus causing reset retry.  After a few times, EH will give
     up disabling the port.

  3. When slave device passes devchk but fails to become accessible
     (TF-wise) after reset.  Original code disables dev1 after 30s
     timeout and continues as if the device doesn't exist, while the
     patched code fails reset.  When this happens, new code fails
     reset on whole port rather than proceeding with only the primary
     device.

  If the failing device is suffering transient problems, new code
  retries reset which is a better behavior.  If the failing device is
  actually broken, the net effect is identical to it, but not to the
  other device sharing the channel.  In the previous code, reset would
  have succeeded after 30s thus detecting the working one.  In the new
  code, reset fails and whole port gets disabled.  IMO, it's a
  pathological case anyway (broken device sharing bus with working
  one) and doesn't really matter.

* ata_bus_softreset() is changed to return error code from
  ata_bus_post_reset().  It used to return 0 unconditionally.

* Spin up waiting is to be removed and not converted to honor
  deadline.

* To be on the safe side, deadline is set to 40s for the time being.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

All patches authored and signed-off-by Alan Cox, sent on Mar 7, 2007.
I merely combined them all into a single patch.
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Add missing #ifdef CONFIG_PM conditionals around all PM related parts
in libata LLDs.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Keeps the behaviour consistent and easier to understand.
Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Fix the PIO mode 2 using mode 0 timings -- this driver should enable the
fast timing bank starting with PIO2, just like the ata_piix driver does.
Also, fix/rephrase some comments while at it.
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

This patch is against each libata driver.

Two IRQ calls are added in ata_port_operations.
- irq_on() is used to enable interrupts.
- irq_ack() is used to acknowledge a device interrupt.

In most drivers, ata_irq_on() and ata_irq_ack() are used for
irq_on and irq_ack respectively.

In some drivers (ex: ahci, sata_sil24) which cannot use them
as is, ata_dummy_irq_on() and ata_dummy_irq_ack() are used.
Signed-off-by: NKou Ishizaki <kou.ishizaki@toshiba.co.jp>
Signed-off-by: NAkira Iguchi <akira2.iguchi@toshiba.co.jp>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Convert libata core layer and LLDs to use iomap.

* managed iomap is used.  Pointer to pcim_iomap_table() is cached at
  host->iomap and used through out LLDs.  This basically replaces
  host->mmio_base.

* if possible, pcim_iomap_regions() is used

Most iomap operation conversions are taken from Jeff Garzik
<jgarzik@pobox.com>'s iomap branch.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Update libata LLDs to use devres.  Core layer is already converted to
support managed LLDs.  This patch simplifies initialization and fixes
many resource related bugs in init failure and detach path.  For
example, all converted drivers now handle ata_device_add() failure
gracefully without excessive resource rollback code.

As most resources are released automatically on driver detach, many
drivers don't need or can do with much simpler ->{port|host}_stop().
In general, stop callbacks are need iff port or host needs to be given
commands to shut it down.  Note that freezing is enough in many cases
and ports are automatically frozen before being detached.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

sht->max_sectors is overrided unconditionally in ->slave_configure.
There's no reason to set it to any value.
Signed-off-by: NTejun Heo <htejun@gmail.com>

This patch adds the suspend/resume callbacks for drivers which don't need
any additional help (beyond the pci resume quirk patch I posted earlier
anyway). Also bring version numbers back inline with master copies.
Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Many LLDs are missing sht->slave_destroy.  The method is mandatory to
support device warm unplugging (echo 1 > /sys/.../delete).  Without
it, libata might access released scsi device.
Signed-off-by: NTejun Heo <htejun@gmail.com>

* Use PCI_VDEVICE() macro
* const-ify pci_device_id table
* standardize list terminator as "{ }"
* convert spaces to tab in pci_driver struct (Alan-ism)
* various minor whitespace cleanups
Signed-off-by: NJeff Garzik <jeff@garzik.org>

This removes the layering violation where drivers have to fiddle
directly with EH flags. Instead we now recognize -ENOENT means "no port"
and do the handling in the core code.

This also removes an instance of a call to disable the port, and an
identical printk from each driver doing this. Even better - future rule
changes will be in one place only.
Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The vast majority of drivers and changes are from Alan Cox.  Albert Lee
contributed and maintains pata_pdc2027x.  Adrian Bunk, Andrew Morton,
and Tejun Heo contributed various minor fixes and updates.
Signed-off-by: NJeff Garzik <jeff@garzik.org>