When adding support for both video and VBI, I missed the mmap ioctl.  Add
the missing call.
Signed-off-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Add support for raw VBI capture for the em28xx bridge, currently only for
NTSC.  Support for PAL capture to follow shortly (including the removal of
numerous hard-coded NTSC-specific sizes for capture buffers, etc).

Note that the code currently changes the default current norm from PAL to
NTSC (so that zvbi-ntsc-cc works properly).  The default norm really should
be moved into a board-level parameter.

This work was sponsored by EyeMagnet Limited.
Signed-off-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Add code enabling the VBI registers for variants of the em28xx chip that
support VBI, and make sure the isoc streaming code continues to work for
the video component of the stream (note the video and vbi data arrive
intermixed on the same isoc pipe).

Note that this version just drops the actual VBI data onto the floor as
opposed to processing it.  The "#ifdef 0" tags are for the videobuf code that
appears in the next patch in this series.

We created a separate version of the isoc_copy version for parsing the version
of the stream that includes VBI data.  In theory, they might be able to be
merged at some point in the future, but the initial goal is to ensure that we
do not cause any regressions with devices that do not have VBI support.

This work was sponsored by EyeMagnet Limited.
Signed-off-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Properly document the video input control register, in preparation for the
addition of VBI support.  Note this patch makes no functional changes.
Signed-off-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Added Kworld DVD Maker 2
Thanks to C Western <l@c-m-w.me.uk> for reporting this board.
Signed-off-by: NDouglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

There are some extra parenthesis at the clauses, and some switch() tests
for boards that don't have i2c ir. Remove those extra code.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Currently, the logic to load ir i2c ancillary module is broken. It is
associated to Hauppauge devices with IR flag on their eeprom, no matter
if the device uses i2c or em28xx direct IR support. That's wrong.

Instead, add a flag to the boards that use i2c IR chips and load the
module only for those devices and if ir is not disabled.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

ir-kbd-i2c's ir_probe() function can be called much later (i.e. at
ir-kbd-i2c module load), than the lifetime of a struct IR_i2c_init_data
allocated off of the stack in cx18_i2c_new_ir() at registration time.
Make sure we pass a pointer to a persistent IR_i2c_init_data object at
i2c registration time.

Thanks to Brian Rogers, Dustin Mitchell, Andy Walls and Jean Delvare to
rise this question.

Before this patch, if ir-kbd-i2c were probed after em28xx, trash data
were used. After the patch, no matter what order, it is properly
reported as tested by me:

input: i2c IR (i2c IR (EM2840 Hauppaug as /class/input/input10
ir-kbd-i2c: i2c IR (i2c IR (EM2840 Hauppaug detected at i2c-4/4-0030/ir0 [em28xx #0]
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Currently, V4L uses a scancode table whose index is the scancode and
the value is the keycode. While this works, it has some drawbacks:

1) It requires that the scancode to be at the range 00-7f;

2) keycodes should be masked on 7 bits in order for it to work;

3) due to the 7 bits approach, sometimes it is not possible to replace
the default keyboard to another one with a different encoding rule;

4) it is different than what is done with dvb-usb approach;

5) it requires a typedef for it to work. This is not a recommended
Linux CodingStyle.

This patch is part of a larger series of IR changes. It basically
replaces the IR_KEYTAB_TYPE tables by a structured table:
struct ir_scancode {
       u16     scancode;
       u32     keycode;
};

This is very close to what dvb does. So, a further integration with DVB
code will be easy.

While we've changed the tables, for now, the IR keycode handling is still
based on the old approach.

The only notable effect is the redution of about 35% of the ir-common
module size:

   text    data     bss     dec     hex filename
   6721   29208       4   35933    8c5d old/ir-common.ko
   5756   18040       4   23800    5cf8 new/ir-common.ko

In thesis, we could be using above u8 for scancode, reducing even more the size
of the module, but defining it as u16 is more convenient, since, on dvb, each
scancode has up to 16 bits, and we currently have a few troubles with rc5, as their
scancodes are defined with more than 8 bits.

This patch itself shouldn't be doing any functional changes.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

[mchehab@redhat.com: Fix a few wrong IR keymaps]
Signed-off-by: NShine Liu <shinel@foxmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Add support for the remote control that comes with the Cinergy Hybrid T USB XS

Thanks to Jelle de Jong for providing sample hardware to test with.

Cc: Jelle de Jong <jelledejong@powercraft.nl>
Signed-off-by: NDevin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Fixed eeprom hash table
Signed-off-by: NDouglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

V4L2 API (chapter 1.5) states that:

	Drivers must implement all input ioctls when the device has one
	or more inputs, all output ioctls when the device has one or more outputs.
	When the device has any audio inputs or outputs the driver must set the
	V4L2_CAP_AUDIO flag in the struct v4l2_capability returned by the
	VIDIOC_QUERYCAP ioctl.

So, devices without audio input should return -EINVAL.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Even devices without ac97 needs to call analog audio setup function, to
properly set xclk and mute/unmute.

Thanks to Angelo Cano <acano@fastmail.fm> for reporting and testing it.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

There is no point in defining I2C adapter IDs when no code is using
them. As this field might go away in the future, stop using it when
we don't need to.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

In the past, some devices with saa711x had their parameters controlled
directly inside em28xx driver, instead of using their proper module for
it.

Due to that, the ac97 controls were mixed with saa711x ones.

Older patches removed all saa711x controls, but we still need to control
ac97 devices on em28xx, since we don't have a separate v4l2 device for
it.

The proper way to address is to create a separate ac97 v4l2 device.
While we don't have it, we should clean up the code to allow having a
better view of what is part of em28xx core code and what's due to ac97
control inside it.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

As em28xx chip has nothing to do with volume/mute controls, rename those
controls to properly indicate that they control the companion AC97 chip
that it is inside the boards with this chip.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

em28xx: Add support for Gadmei UTV330+
Signed-off-by: NZhenyu Wang <zhen78@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

We should call em28xx_ir_init(dev) only when disable_ir is true.
Signed-off-by: NShine Liu <shinel@foxmail.com>
Reviewed-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

[mchehab@redhat.com: fix merge conflict and a few CodingStyle issues]
Signed-off-by: NSteve Gotthardt <gotthardt@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Restore support for digital tuning caused by regression during introduction
of disable_i2c_gate parameter to zl10353 driver.

Thanks to user "Xwang" for reporting the problem and testing the fix

Cc: Xwang <xwang1976@email.it>
Signed-off-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Register 0x13 seems to be a sort of image control, maybe gamma, white
level or black level. Lower values produce better images, while higher
values increases the contrast and shifts colors to green. 0xff produces
a black image. This register is not Silvercrest-specific, so its code
should be moved to a better place.

If this register is left alone, a random value can be found at the
register, producing weird results.

While here, let's remove register 0x0d, as it had no noticed effect at
the image.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Silvercrest mt9v011 sensor produces a 640x480 image. However,
previously, the code were getting only half of the lines and merging two
consecutive frames to "produce" a 640x480 image.

With the addition of progressive mode, now em28xx is working with a full
image. However, when the number of lines is bigger than 240, the
beginning of some odd lines are filled with blank.

After lots of testing, and physically checking the device for a Xtal, it
was noticed experimentally that mt9v011 is using em28xx XCLK as its
clock. Due to that, changing XCLK value changes the maximum speed of the
stream.

At the tests, it were possible to produce up to 32 fps, using a 30 MHz
XCLK. However, at that rate, the artifacts happen even at 320x240. Lower
values of XCLK produces artifacts only at 640x480.

At some values of xclk (for example XCLKK = 6 MHz, 640x480), it is
possible to see an invalid sucession of artifacts with this pattern:

.xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
..xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
...xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
....xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
.xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
..xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
...xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
....xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx

(where the dots represent the blanked pixels)

So, it seems that a waveform in the format of a ramp is interferring at
the image.

The cause of this interference is currently unknown. Some possibilities
are:
	- electrical interference (maybe this device is broken?);
	- some issue at mt9v011 programming;
	- some bug at em28xx chip.

So, for now, let's be conservative and use a value of XCLK that we know
for sure that it won't cause artifacts.

As I'm waiting for more of such devices with different em28xx chipset
revisions, I'll have the opportunity to double check the issue with
other pieces of hardware.

Later patches can vary XCLK depending on the vertical resolutions, if a
proper fix is not discovered.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

em28xx_pre_card_setup() is meant to contain board-specific initialization. Also,
as autodetection sometimes occur only after having i2c bus enabled, this
function may need to be called later.

Moving those setups to happen outside the function avoids calling it twice without
need and without duplicating output lines at dmesg.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

We don't know the xtal frequency of Silvercrest, but we need to have
some value in order to allow controlling the frame rate frequency. The
value is probably still wrong, since the manufacturer announces this
device as being capable of 30fps, but the maximum we can get is
13.5 fps.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Due to historical reasons, em28xx driver gets two consecutive frames and
fold them into an unique framing, doing interlacing. While this works
fine for TV images, this produces two bad effects with webcams:

1) webcam images are progressive. Merging two consecutive images produce
interlacing artifacts on the image;

2) since the driver needs to get two frames, it reduces the maximum
frame rate by two.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

As reported by hermann pitton <hermann-pitton@arcor.de>, some devices
has a different chip id for em2710 (likely the older ones):

em28xx: New device @ 480 Mbps (eb1a:2710, interface 0, class 0)
em28xx #0: Identified as EM2710/EM2750/EM2751 webcam grabber (card=22)
em28xx #0: em28xx chip ID = 17
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Thanks to hermann pitton <hermann-pitton@arcor.de> for pointing this new
variation.
Tested-by: Nhermann pitton <hermann-pitton@arcor.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

em28xx doesn't have temporal scaling. However, on webcams, sensors are
capable of changing the output rate. So, VIDIOC_[G|S]_PARM ioctls should
be passed to the sensor for it to properly set frame rate.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This device uses msp34xx and uses 2.048 MHz frequency for I2S
communication.

Thanks to Angelo Cano <acano@fastmail.fm> for pointing the issues with
this device and proposing an approach for fixing the issue.
Tested-by: NAngelo Cano <acano@fastmail.fm>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Some mt9v011 webcams report 0x8332 chip version, instead of 0x8243. From
the revision history at the mt9v011 datasheet, it seems that the chip
version has changed from the first release of the chip.

Thanks-to hermann pitton <hermann-pitton@arcor.de> for pointing this to
me, on his tests with a Silvercrest webcam.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

When the change was introduced in the zl10353 for the i2c gate behavior, this
broke the HVR-900 which was not behind a gate.  Use a version of the zl10353
config profile that indicates the tuner is not behind such a gate.

Without this patch the first tune succeeds, but subsequent tuning attempts
will fail.

The change also renames the terratec zl10353 profile I wrote to be more
generic, since it is shared by the non-terratec device.

Thanks to Michael Krufky for providing a HVR-900 and DVB-T environment to test
with.

Cc: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The Pinnacle Hybrid Pro 320e was missing a demod config for the xc3028, which
is required for digital tuning to work properly.  Add the missing profile.

Thanks to Andreas Lunderhage for testing patches and providing a remote debug
environment.

Cc: Andreas Lunderhage <lunderhage@home.se>
Signed-off-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

In cases where the device has a generic Empia USB ID, the call in the
precard setup phase did not set the tuner GPIO.  As a result, the tuner may
not be taken out of reset before attempting initialization in the analog
driver.

This problem was not seen before with the EVGA inDtube, since that particular
board has the analog GPIO setup to include taking the tuner out of reset.

Thanks to Andreas Lunderhage for testing patches and providing a remote debug
environment for the Pinnacle 320e.

Cc: Andreas Lunderhage <lunderhage@home.se>
Signed-off-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Set the GPIO properly for the analog side of the Pinnacle Hybrid Pro, or else
the emp202 doesn't get detected properly.
Signed-off-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Setup the GPIOs properly and enable support for the DVB side of the Pinnacle
Hybrid Pro USB stick.

Thanks to Andreas Lunderhage for testing patches and providing a remote debug
environment.

Cc: Andreas Lunderhage <lunderhage@home.se>
Signed-off-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Andy walls pointed out that we were passing 0x5d to the TUNER_GO register,
instead of 0x01.  Set the register properly (note the code did still work with
the incorrect value, so this does not address a regression).

Thanks to Andy Walls for noticing the issue.

Cc: Andy Walls <awalls@radix.net>
Signed-off-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The Terratec Cinergy T XS USB can have either a zl10353 or an mt352.  Add
support for the MT352 variant.

Thanks to Jelle de Jong for providing a unit to test/debug with.

Cc: Jelle de Jong <jelledejong@powercraft.nl>
Signed-off-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Thanks to Wally <wally@voosen.eu> for bringing the issue and helping
with the tests.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>