When switching between STA and AP modes, memory allocated for Rx vring leaks
This is because start_ap() allocates Rx vring but stop_ap() do not free it.
Logically, Rx vring is not valid (HW can't use it anymore), so free it in reset()
Also, check double init for Rx vring and bail out with -EINVAL
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Convert 2 often printed messages to dynamic ones
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Configure hardware to perform full reset on "power good". This mean,
reset HW on system boot. This improves card stability.
By default this is off.
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Put all registers in order for easier navigation;
fix naming to reflect hardware cluster
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Hardware bug triggered by the MSI init while INTx asserted for some reason.
De-assert INTx prior to MSI set-up
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Useful to detect hardware problems
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When FW crashes, dmesg get polluted with the "FW not ready"
error message. Print it only once per FW lifecycle
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Support for new chip revision. Revision read from the
internal register, PCIE config's "revision id" register
do not indicate HW version properly
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Introduce enum to describe mapping type; allow 'none' in addition to
'single' and 'page'; this is preparation for GSO
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When setting fragmented skb for Tx, assign skb to the last descriptor
and set number of fragments in the 1-st one
On Tx complete, HW sets "DU" bit in Tx descriptor only for the last
descriptor; so search for it using number of fragments field.
Middle descriptors may have "DU" bit not set by the hardware.
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

New firmware do support scan while connected. Enable it.
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When connection established, as reported by WMI_CONNECT_EVENTID,
4-way handshaking required for the secure connection is not done
yet. It is indicated by another WMI event. Wait for it and only then
allow data traffic. In case of non-secure connection, FW reports
"data port open" immediately after connection.
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Encode/decode helpers
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The registers for temperature compensation need to
be programmed only for active chains. Use the TX chainmask
to make sure that this is done properly for QCA953x.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Along with AR9340 and AR955x, this is also needed for
the QCA953x SoC.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Eeprom read operations are mixed in the probe function.
Make the code more readable and clean by extracting this code and
moving it in a dedicated function.

The variable eeprom_cck_table_adr, now useless, is here because
it will be needed for rtl8187se support, that I hope to add soon.
Signed-off-by: NAndrea Merello <andrea.merello@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

SLOT, SIFS, DIFS, EIFS, CW and ACK-timeout registers are set in an
RF-code callback and their values are fixed.

This patch moves this off the rf-code, and introduce two new functions
that calculate these values depending by slot time and CW values
requested by mac80211.

This seems to improve performances on my setup.

Currently the ack and slot time values could be stored in a local
variable, but this patch stores it in the driver "priv" structure
because it will be useful for rtl8187se support that will be added
(hopefully) soon.
Signed-off-by: NAndrea Merello <andrea.merello@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Basic rates setting is done with hardcoded register write with
fixed settings.

This patch introduces a new function that makes it possible to
configure basic rates and it add a check for mac80211
BSS_CHANGED_BASIC_RATES flag in order to eventually invoke that
function when needed.
Signed-off-by: NAndrea Merello <andrea.merello@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

While changing board-type variable to enum, I have added enum
value for rtl8187se by mistake.
This will causes gcc warnings with unhandled switch/cases.

Remove it temporarily until I will push also rtl8187se changes.
Signed-off-by: NAndrea Merello <andrea.merello@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The nl80211 iftype was converted to a mode value and stored in
brcmf_cfg80211_vif structure. The value was used only within
brcmfmac driver to decide execution of conditional code. Better
use wireless_dev::iftype for that as the wdev is contained in
the brcmf_cfg80211_vif structure.
Reviewed-by: NDaniel (Deognyoun) Kim <dekim@broadcom.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NFranky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When the SDIO driver goes in low power state it must assure that
a clock request in ChipCLKCSR is set. Otherwise waking up the
device can fail. The register is read and if necessary the ALP
clock will be requested.
Reviewed-by: NDaniel (Deognyoun) Kim <dekim@broadcom.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NFranky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When connecting without specifying the channel it can take quite
some time to connect. This is because not all parameters for the
scan operation are set to optimized values. This patch changes
these parameters resulting in a much faster connect in certain
situations.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NFranky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NDaniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

SDIO tx uses a sequence number which is common for data
and control. This requires that access to this sequence number
is protected. A mutex was used to achieve this, but it also
required the reordering of code for tx control.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NFranky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NDaniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

BCM4354 is an a/b/g/n/ac 2x2 WiFi chip. This patch adds support for it through
SDIO interface.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Signed-off-by: NFranky Lin <frankyl@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Samuel Ortiz <sameo@linux.intel.com> says:

"NFC: 3.15: First pull request

This is the NFC pull request for 3.15. With this one we have:

- Support for ISO 15693 a.k.a. NFC vicinity a.k.a. Type 5 tags. ISO
  15693 are long range (1 - 2 meters) vicinity tags/cards. The kernel
  now supports those through the NFC netlink and digital APIs.

- Support for TI's trf7970a chipset. This chipset relies on the NFC
  digital layer and the driver currently supports type 2, 4A and 5 tags.

- Support for NXP's pn544 secure firmare download. The pn544 C3 chipsets
  relies on a different firmware download protocal than the C2 one. We
  now support both and use the right one depending on the version we
  detect at runtime.

- Support for 4A tags from the NFC digital layer.

- A bunch of cleanups and minor fixes from Axel Lin and Thierry Escande."
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

... to remove some more dups.
Signed-off-by: NOleksij Rempel <linux@rempel-privat.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NOleksij Rempel <linux@rempel-privat.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NOleksij Rempel <linux@rempel-privat.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NOleksij Rempel <linux@rempel-privat.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NOleksij Rempel <linux@rempel-privat.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NOleksij Rempel <linux@rempel-privat.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NOleksij Rempel <linux@rempel-privat.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NOleksij Rempel <linux@rempel-privat.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NOleksij Rempel <linux@rempel-privat.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NOleksij Rempel <linux@rempel-privat.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NOleksij Rempel <linux@rempel-privat.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NOleksij Rempel <linux@rempel-privat.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NOleksij Rempel <linux@rempel-privat.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NOleksij Rempel <linux@rempel-privat.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>