* Unify calling of early_serial_txx9_setup.
* Use dedicated serial clock on RBTX4938.
Signed-off-by: NAtsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Make some TX4938 SoC specific code independent from board specific code.
Signed-off-by: NAtsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Unify registration of txx9wdt platform device.
Signed-off-by: NAtsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

From: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Date: Thu, 24 Jul 2008 00:25:16 +0900
Subject: [PATCH] txx9: PCI error handling

Add more control and detailed report on PCI error interrupt.
Signed-off-by: NAtsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

SYS_SUPPORTS_64BIT_KERNEL is enabled for RBTX4927/RBTX4938, but
actually it was broken for long time (or from the beginning).  Now it
should work.
Signed-off-by: NAtsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

* Unify (and fix) mem_tx4938.c and mem_tx4927.c
* Simplify prom_init
* Kill volatiles and unused definitions for tx4927.h and tx4938.h
Signed-off-by: NAtsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Make single kernel can be used on RBTX4927/37/38.  Also make
some SoC-specific code independent from board-specific code.
Signed-off-by: NAtsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Split out PCIC dependent code and SoC dependent code from board dependent
code.  Now TX4927 PCIC code is independent from TX4927/TX4938 SoC code.
Also fix some build problems on CONFIG_PCI=n.

As a bonus, "FPCIB0 Backplane Support" is available for all TX39/TX49 boards
and PCI66 support is available for all TX49 boards.
Signed-off-by: NAtsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Move arch/mips/{jmr3927,tx4927,tx4938} into arch/mips/txx9/ tree.
This will help more code sharing and maintainance.
Signed-off-by: NAtsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

* Do not use non-standard I/O accessors, such as reg_rd08, etc.
* Kill unnecessary wbflush()
* Kill tx4938_mips.h
* Kill unnecessary includes
Signed-off-by: NAtsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Use generic txx9 gpio (and gpiolib) for RBHMA4500 board.
Signed-off-by: NAtsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Convert jmr3927_clock_event_device to more generic
txx9tmr_clock_event_device which supports one-shot mode.  The
txx9tmr_clock_event_device can be used for TX49 too if the cp0 timer
interrupt was not available.

Convert jmr3927_hpt_read to txx9_clocksource driver which does not
depends jiffies anymore.  The txx9_clocksource itself can be used for
TX49, but normally TX49 uses higher precision clocksource_mips.
Signed-off-by: NAtsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Cleanup jmr3927, tx4927 and tx4938 irq codes, using common IRQ_CPU,
I8259 and IRQ_TXX9 irq routines.
Signed-off-by: NAtsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NRalf Baechle <ralf@linux-mips.org>