The axp288 has the following irqs 2 times: VBUS_FALL, VBUS_RISE,
VBUS_OV. On boot / reset the enable flags for both the normal and alt
version of these irqs is set.

Since we were only listing the normal version in the axp288 regmap_irq
struct, we were never disabling the alt versions of these irqs.

Add the alt versions to the axp288 regmap_irq struct, so that these
get properly disabled.

Together with the other axp288 fixes in this series, this fixes the axp288
irq contineously triggering.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Acked-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

The interrupt line of the entire family of axp2xx pmics is active-low,
for devicetree enumerated irqs, this is dealt with in the devicetree.

ACPI irq resources have a flag field for this too, I tried using this
on my CUBE iwork8 Air tablet, but it does not contain the right data.

The dstd shows the irq listed as either ActiveLow or ActiveHigh,
depending on the OSID variable, which seems to be set by the
"OS IMAGE ID" in the BIOS/EFI setup screen.

Since the acpi-resource info is no good, simply pass in IRQF_TRIGGER_LOW
on the axp288.

Together with the other axp288 fixes in this series, this fixes the axp288
irq contineously triggering.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Acked-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

This declaration has never been used and is likely some left over from
early prototypes of the code, just remove it.
Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

The PRCM block on the A23 contains a message box like interface to
the registers for the analog path controls of the internal codec.

Add a sub-device for it.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Acked-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Currently we leak a lot of things when tearing down the IRQs this patch
fixes this cleaning up both the IRQ mappings and the IRQ domain itself.
Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

We have arizona_map_irq we might as well use it rather than hard coding
it in several places.
Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

This hardware block could at used at same time for PWM generation
and IIO timers.
PWM and IIO timer configuration are mixed in the same registers
so we need a multi fonction driver to be able to share those registers.

version 7:
- rebase on v4.10-rc2

version 6:
- rename files to stm32-timers
- rename functions to stm32_timers_xxx

version 5:
- fix Lee comments about detect function
- add missing dependency on REGMAP_MMIO

version 4:
- add a function to detect Auto Reload Register (ARR) size
- rename the structure shared with other drivers

version 2:
- rename driver "stm32-gptimer" to be align with SoC documentation
- only keep one compatible
- use of_platform_populate() instead of devm_mfd_add_devices()
Signed-off-by: NBenjamin Gaignard <benjamin.gaignard@st.com>
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Intel Apollo Lake SoC exposes serial SPI flash through the LPC device. The
SPI flash host controller is not discoverable through PCI config cycles
because P2SB (function 0 of the device 13) is hidden by the BIOS. We unhide
the device briefly in order to read BAR 0 of the SPI host controller.
Signed-off-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: NLee Jones <lee.jones@linaro.org>
Acked-by: NMarek Vasut <marek.vasut@gmail.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Many Intel CPUs including Haswell, Broadwell and Baytrail have SPI serial
flash host controller as part of the LPC device. This will populate an MFD
cell suitable for the SPI host controller driver if we know that the LPC
device has one.
Signed-off-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

This adds TMU (Time Management Unit) support for Intel BXT platform.
It enables the alarm wake-up functionality in the TMU unit of Whiskey Cove
PMIC.
Signed-off-by: NNilesh Bacchewar <nilesh.bacchewar@intel.com>
Reviewed-by: NMika Westerberg <mika.westerberg@linux.intel.com>
[andy: resolve merge conflict in Kconfig]
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>

This patch fix spelling typos in printk and kconfig.
Signed-off-by: NMasanari Iida <standby24x7@gmail.com>
Acked-by: NRandy Dunlap <rdunlap@infradead.org>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

TPS65217 INT pin is used for the system wakeup from suspend mode.
This patch enables push button or charger input event as a wakeup source.
Signed-off-by: NMilo Kim <woogyom.kim@gmail.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Rework the IRQ handler by using HW IRQ number and status bit.

Each HW IRQ number is matched with TPS65217 register layout[*].
(USB IRQ number is 0, AC is 1, Push button is 2)

When an interrupt is enabled, mask bit should be cleared (unmasked).
If an interrupt is disabled, then mask bit should be set (masked).
This mask value is updated into the TPS65217 register in irq_sync_unlock().

Mask bit and interrupt status bit can be handled with HW IRQ number.
Eventually, additional IRQ data, 'tps65217_irqs[]' and the function,
'irq_to_tps65217_irq()' are not necessary.

[*] TPS65217 interrupt register layout

 Bit7  6     5     4     3    2     1     0
----------------------------------------------
| x | PBM | ACM | USBM | x | PBI | ACI | USBI

PBM:  Push button status change interrupt mask
ACM:  AC interrupt mask
USBM: USB power status change interrupt mask
PBI:  Push button status change interrupt
ACI:  AC power status change interrupt
USBI: USB power status change interrupt
x:    Not used
Signed-off-by: NMilo Kim <woogyom.kim@gmail.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

TPS65217 interrupt register includes read/writeable mask bits with
read-only status bits. (bit 4, 5, 6 are R/W, bit 0, 1, 2 are RO)
And reserved bit is not required.

Register update operation is preferred for disabling all interrupts during
the device initialisation.
Signed-off-by: NMilo Kim <woogyom.kim@gmail.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

TPS65217 MFD is an interrupt controller and MFD slave devices like
tps65217-charger and tps65217-pwrbutton request an interrupt to handle
each HW event.

Currently, TPS65217 IRQ name is not defined, so the result is as below.

root@arm:~# cat /proc/interrupts
...
182:          0      INTC   7 Level     tps65217-irq
183:          0         -   1 Edge      tps65217-charger
185:          0         -   2 Edge      tps65217_pwrbutton

This patch specifies the name of the interrupt controller.

182:          0      INTC   7 Level     tps65217-irq
183:          0  tps65217   1 Edge      tps65217-charger
185:          0  tps65217   2 Edge      tps65217_pwrbutton
Signed-off-by: NMilo Kim <woogyom.kim@gmail.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

TPS65217 IRQ domain should be removed and initialised as NULL when the
module is unloaded for the next use. When tps65217.ko is loaded again,
it causes the page fault. This patch fixes the error below.

root@arm:~# lsmod | grep "tps"
tps65217_charger        3538  0
tps65218_pwrbutton      2974  0
tps65217                6710  1 tps65217_charger

root@arm:~# modprobe -r tps65217_charger

root@arm:~# modprobe tps65217.ko
[   71.990277] Unable to handle kernel paging request at virtual address bf055944
[   71.998063] pgd = dd3a4000
[   72.000904] [bf055944] *pgd=9e6f7811, *pte=00000000, *ppte=00000000
[   72.007567] Internal error: Oops: 7 [#1] SMP ARM
[   72.012404] Modules linked in: tps65217(+) evdev musb_dsps musb_hdrc udc_core tps65218_pwrbutton usbcore phy_am335]
[   72.055700] CPU: 0 PID: 243 Comm: modprobe Not tainted 4.9.0-rc5-next-20161114 #3
[   72.063531] Hardware name: Generic AM33XX (Flattened Device Tree)
[   72.069899] task: de714380 task.stack: de7e6000
[   72.074655] PC is at irq_find_matching_fwspec+0x88/0x100
[   72.080211] LR is at 0xde7e79d8
[   72.083496] pc : [<c01a5d88>]    lr : [<de7e79d8>]    psr: 200e0013
[   72.083496] sp : de7e7a78  ip : 00000000  fp : dd138a68
[   72.095506] r10: c0ca04f8  r9 : 00000018  r8 : de7e7ab8
[   72.100973] r7 : 00000001  r6 : c0c4517c  r5 : df963f68  r4 : de321980
[   72.107797] r3 : bf055940  r2 : de714380  r1 : 00000000  r0 : 00000000
[   72.114633] Flags: nzCv  IRQs on  FIQs on  Mode SVC_32  ISA ARM  Segment none
[   72.122084] Control: 10c5387d  Table: 9d3a4019  DAC: 00000051
[   72.128097] Process modprobe (pid: 243, stack limit = 0xde7e6218)
[   72.134489] Stack: (0xde7e7a78 to 0xde7e8000)
[   72.139060] 7a60:                                                       df963f68 de7e7ab8
[   72.147643] 7a80: 00000000 dd0e1000 dd491e20 c01a6ea0 600e0013 c01a5dc0 dd138a68 c0c45138
[   72.156216] 7aa0: df963f68 00000000 df963f68 dd0e1010 00000000 c01a71a4 df963f68 00000001
[   72.164800] 7ac0: 00000002 de7e7ac0 c80048b8 dd0adf00 df963f68 c0c4517c 00000000 de7e7b50
[   72.173369] 7ae0: 00000018 c0ca04f8 dd138a68 c01a5dc0 df963f68 dd0e1010 00000000 dd0e1000
[   72.181942] 7b00: dd491e20 c0653a70 df963f58 00000001 00000002 00000000 00000000 00000000
[   72.190522] 7b20: 600e0093 c0cbf8f0 c0c0512c c0193674 00000001 00000080 00000000 c0554984
[   72.199096] 7b40: 00000000 00000000 800e0013 c0553858 df963f68 00000000 00000000 00000000
[   72.207674] 7b60: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[   72.216239] 7b80: 00000000 00000000 00000000 00000000 00000000 00000000 dd0e1000 c0544d24
[   72.224816] 7ba0: dd491e10 dd0e1010 dd16e800 bf1d517c bf1d5620 dd0e1010 c1497ed4 bf1d5620
[   72.233398] 7bc0: dd0e1010 fffffdfb bf1d5620 bf1d5620 00000000 c054537c c0545330 dd0e1010
[   72.241967] 7be0: c1497ed4 00000000 bf1d5620 c05433ac 00000000 00000000 de7e7c28 c0543570
[   72.250537] 7c00: 00000001 c1497e90 00000000 c0541884 de080cd4 dd44b7d4 dd0e1010 dd0e1010
[   72.259109] 7c20: dd0e1044 c05430c8 dd0e1010 00000001 dd0e1010 dd0e1018 dd0e1010 c0c9e328
[   72.267676] 7c40: de5d4020 c0542760 dd0e1018 dd0e1010 00000000 c0540ba8 dd138a40 c048dec4
[   72.276253] 7c60: 00000000 dd0e1000 00000001 dd0e1000 dd0e1010 dd0e1000 bf233de0 dd138a40
[   72.284829] 7c80: dd0e1010 c05450a0 000000bf 00000000 dd138a60 00000001 dd0e1000 c0571240
[   72.293398] 7ca0: 00000000 dd1ce9c0 00000040 dd1ce9cc bf233de0 00000003 de5d4020 ffffffff
[   72.301969] 7cc0: 00000004 dd0adf00 00000000 c0571408 00000000 00000000 dd0adf00 de5d4020
[   72.310543] 7ce0: c057146c dd1ce9c0 bf233d14 de5d4020 de7fb3d0 00000004 bf233d14 ffffffff
[   72.319120] 7d00: 00000018 dd49bf30 c01cedc0 c05714d0 00000000 00000000 dd0adf00 de322810
[   72.327692] 7d20: de322810 00000000 dd033000 000000f0 00000001 bf2333fc 00000000 00000000
[   72.336269] 7d40: dd0adf00 de5d4020 000000b6 bf233e40 de5d4020 bf233968 de5d4004 de5d4000
[   72.344848] 7d60: bf233314 c06148ac de5d4020 c1497ed4 00000000 bf233e40 00000000 c05433ac
[   72.353422] 7d80: 00000000 de5d4020 bf233e40 de5d4054 00000000 bf236000 00000000 c0543538
[   72.362002] 7da0: 00000000 bf233e40 c0543484 c05417e4 de1442a4 de5d04d0 bf233e40 de321300
[   72.370582] 7dc0: c0caa5a4 c05429fc bf233be0 bf233e40 c0cbfa44 bf233e40 c0cbfa44 dd2f7740
[   72.379148] 7de0: bf233f00 c05442f0 bf233e8c bf233e24 c0cbfa44 c0615ae0 00000000 bf233f00
[   72.387718] 7e00: c0cbfa44 c010186c 200f0013 c0191650 de714380 00000000 600f0013 00000040
[   72.396286] 7e20: dd2f7740 c018f1ac 00000001 c0c8356c 024000c0 c01a8854 c0c56e0e c028225c
[   72.404863] 7e40: dd2f7740 c0191984 de714380 dd2f7740 00000001 bf233f00 bf233f00 c0cbfa44
[   72.413440] 7e60: dd2f7740 bf233f00 00000001 dd49bf08 dd49bf30 c0230998 00000001 c0c8356c
[   72.421997] 7e80: c0c4c536 c0cbfa44 c0c0512c c01d2070 bf233f0c 00007fff bf233f00 c01cf5b8
[   72.430570] 7ea0: 00000000 c1475134 c01cee34 bf23411c bf233f48 bf234054 bf234150 00000000
[   72.439144] 7ec0: 024002c2 de7fbf40 0009bc20 c02776ac ff800000 00000000 00000000 bf233670
[   72.447723] 7ee0: 00000004 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[   72.456298] 7f00: 00000000 00000000 00000000 00000000 c01d2590 0000aa41 00000000 00000000
[   72.464862] 7f20: 000b2549 e12c3a41 00000051 de7e6000 0009bc20 c01d2630 00000530 e12b9000
[   72.473438] 7f40: 0000aa41 e12c1434 e12c1211 e12c336c 00001150 00001620 00000000 00000000
[   72.482003] 7f60: 00000000 000010fc 00000035 00000036 0000001d 0000001a 00000017 00000000
[   72.490564] 7f80: de7e6000 3ba39a00 0009b008 0009b718 00000080 c0107704 de7e6000 00000000
[   72.499141] 7fa0: 0009f609 c0107560 3ba39a00 0009b008 000a7b08 0000aa41 0009bc20 0000aa41
[   72.507717] 7fc0: 3ba39a00 0009b008 0009b718 00000080 00000001 00000008 0009ab14 0009f609
[   72.516290] 7fe0: bea31ab8 bea31aa8 0001e5eb b6e83b42 800f0030 000a7b08 0000ffff 0840ffff
[   72.524883] [<c01a5d88>] (irq_find_matching_fwspec) from [<c01a6ea0>] (irq_create_fwspec_mapping+0x28/0x2e0)
[   72.535174] [<c01a6ea0>] (irq_create_fwspec_mapping) from [<c01a71a4>] (irq_create_of_mapping+0x4c/0x54)
[   72.545115] [<c01a71a4>] (irq_create_of_mapping) from [<c0653a70>] (of_irq_get+0x58/0x68)
[   72.553699] [<c0653a70>] (of_irq_get) from [<c0544d24>] (platform_get_irq+0x1c/0xec)
[   72.561828] [<c0544d24>] (platform_get_irq) from [<bf1d517c>] (tps6521x_pb_probe+0xd0/0x1a8 [tps65218_pwrbutton])
[   72.572581] [<bf1d517c>] (tps6521x_pb_probe [tps65218_pwrbutton]) from [<c054537c>] (platform_drv_probe+0x4c/0xac)
[   72.583426] [<c054537c>] (platform_drv_probe) from [<c05433ac>] (driver_probe_device+0x204/0x2dc)
[   72.592729] [<c05433ac>] (driver_probe_device) from [<c0541884>] (bus_for_each_drv+0x58/0x8c)
[   72.601657] [<c0541884>] (bus_for_each_drv) from [<c05430c8>] (__device_attach+0xb0/0x114)
[   72.610324] [<c05430c8>] (__device_attach) from [<c0542760>] (bus_probe_device+0x88/0x90)
[   72.618898] [<c0542760>] (bus_probe_device) from [<c0540ba8>] (device_add+0x3b8/0x560)
[   72.627203] [<c0540ba8>] (device_add) from [<c05450a0>] (platform_device_add+0xa8/0x208)
[   72.635693] [<c05450a0>] (platform_device_add) from [<c0571240>] (mfd_add_device+0x240/0x338)
[   72.644634] [<c0571240>] (mfd_add_device) from [<c0571408>] (mfd_add_devices+0xa0/0x104)
[   72.653120] [<c0571408>] (mfd_add_devices) from [<c05714d0>] (devm_mfd_add_devices+0x60/0xa8)
[   72.662077] [<c05714d0>] (devm_mfd_add_devices) from [<bf2333fc>] (tps65217_probe+0xe8/0x2ec [tps65217])
[   72.672026] [<bf2333fc>] (tps65217_probe [tps65217]) from [<c06148ac>] (i2c_device_probe+0x168/0x1f4)
[   72.681695] [<c06148ac>] (i2c_device_probe) from [<c05433ac>] (driver_probe_device+0x204/0x2dc)
[   72.690816] [<c05433ac>] (driver_probe_device) from [<c0543538>] (__driver_attach+0xb4/0xb8)
[   72.699657] [<c0543538>] (__driver_attach) from [<c05417e4>] (bus_for_each_dev+0x60/0x94)
[   72.708224] [<c05417e4>] (bus_for_each_dev) from [<c05429fc>] (bus_add_driver+0x18c/0x214)
[   72.716892] [<c05429fc>] (bus_add_driver) from [<c05442f0>] (driver_register+0x78/0xf8)
[   72.725280] [<c05442f0>] (driver_register) from [<c0615ae0>] (i2c_register_driver+0x38/0x80)
[   72.734120] [<c0615ae0>] (i2c_register_driver) from [<c010186c>] (do_one_initcall+0x3c/0x178)
[   72.743055] [<c010186c>] (do_one_initcall) from [<c0230998>] (do_init_module+0x5c/0x1d0)
[   72.751537] [<c0230998>] (do_init_module) from [<c01d2070>] (load_module+0x1d10/0x21c0)
[   72.759933] [<c01d2070>] (load_module) from [<c01d2630>] (SyS_init_module+0x110/0x154)
[   72.768242] [<c01d2630>] (SyS_init_module) from [<c0107560>] (ret_fast_syscall+0x0/0x1c)
[   72.776725] Code: e5944000 e1540006 0a00001b e594300c (e593c004)
[   72.783181] ---[ end trace 0278ec325f4689b8 ]---

Fixes: 6556bdac ("mfd: tps65217: Add support for IRQs")
Signed-off-by: NMilo Kim <woogyom.kim@gmail.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

palmas_dev and palmas_power_off are always assigned together.
So the check for palmas_dev inside palmas_power_off function
is redundant. Removing the same.
Signed-off-by: NKeerthy <j-keerthy@ti.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

As DCVDD will often be supplied by a child node of the MFD, we
can't call mfd_remove_devices as the first step in arizona_dev_exit
as might be expected (tidy up the children before we tidy up the
MFD). We need to disable and put the DCVDD regulator before we call
mfd_remove_devices, to prevent PM runtime from turning this back on we
also need to disable the PM runtime before we do this. Finally we can
not clean up the IRQs until all the MFD children have been removed, as
they may have registered IRQs themselves.

This creates a window of time where the interrupts are enabled but
the PM runtime, on which the IRQ handler depends, is not available,
any interrupts in this window will go unhandled and fill the log with
failed to resume device messages. To avoid this we simply disable the
main IRQ at the start of arizona_dev_exit, we don't need to actually
handle any IRQs in this window as we are removing the driver.
Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

This patch adds support to PM8821 PMIC and interrupt support.
PM8821 is companion device that supplements primary PMIC PM8921 IC.
Signed-off-by: NSrinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Enable MWI mechanism if PCI bus master supports it.

It might be potential benefit in some cases. Documentation [1] says that
standard Memory Write might supply more current data than in the CPU modified
cache line and "trashing a line in the cache may trash some data that is more
current that in the memory line". This allows to avoid potential retries and
other performance degradation issues on the bus.

[1] PCI System Architecture, 4th edition, ISBN: 0-201-30974-2, pp.117-119.
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

The Ricoh RN5T567 is from the same family as the Ricoh RN5T618 is,
the differences are:

+ DCDC4/DCDC5
+ LDO7-10
+ Slightly different output voltage/currents
+ 32kHz Output
+ RTC
+ USB Charger detection
Signed-off-by: NPierre-Hugues Husson <phh@phh.me>
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

The AXP806 supports either master/standalone or slave mode.
Slave mode allows sharing the serial bus, even with multiple
AXP806 which all have the same hardware address.

This is done with extra "serial interface address extension",
or AXP806_BUS_ADDR_EXT, and "register address extension", or
AXP806_REG_ADDR_EXT, registers. The former is read-only, with
1 bit customizable at the factory, and 1 bit depending on the
state of an external pin. The latter is writable. Only when
the these device addressing bits (in the upper 4 bits of the
registers) match, will the device respond to operations on
its other registers.

Add these 2 registers to the regmap so we can access them.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Fix a typo in MODULE_DEVICE_TABLE(). 'pmic_acpi_ids' should be
'bxtwc_acpi_ids'.
Signed-off-by: NWei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Make sure to drop the reference taken by bus_find_device_by_name()
before returning from mfd_clone_cell().

Fixes: a9bbba99 ("mfd: add platform_device sharing support for mfd")
Signed-off-by: NJohan Hovold <johan@kernel.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

'i2c_new_dummy()' does not return an error pointer, so the test can be
simplified to be more consistent.
Signed-off-by: NChristophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

The new sun4i mfd driver is lacking a dependency, triggering very rarely
int randconfig kernel builds:

drivers/mfd/sun4i-gpadc.o: In function `sun4i_gpadc_probe':
sun4i-gpadc.c:(.text.sun4i_gpadc_probe+0x110): undefined reference to `devm_regmap_add_irq_chip'

This adds a 'select REGMAP_IRQ', as the other drivers with this problem do.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

The Kconfig currently controlling compilation of this code is:

drivers/mfd/Kconfig:config ABX500_CORE
drivers/mfd/Kconfig:    bool "ST-Ericsson ABX500 Mixed Signal Circuit register functions"

...meaning that it currently is not being built as a module by anyone.

Lets remove the couple traces of modular infrastructure use, so that
when reading the driver there is no doubt it is builtin-only.

We delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.

We replace module.h with init.h and export.h ; the latter since the
file does export some symbols.
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

The Kconfig currently controlling compilation of this code is:

drivers/mfd/Kconfig:config AB8500_CORE
drivers/mfd/Kconfig:    bool "ST-Ericsson AB8500 Mixed Signal Power Management chip"

...meaning that it currently is not being built as a module by anyone.

Lets remove the couple traces of modular infrastructure use, so that
when reading the driver there is no doubt it is builtin-only.

We also delete the MODULE_LICENSE tag etc. since all that information
was (or is now) contained at the top of the file in the comments.

We replace module.h with init.h and export.h -- the latter since the file
does make use of EXPORT_SYMBOL.
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

The Kconfig currently controlling compilation of this code is:

drivers/mfd/Kconfig:config AB8500_GPADC
drivers/mfd/Kconfig:    bool "ST-Ericsson AB8500 GPADC driver"

...meaning that it currently is not being built as a module by anyone.

Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.

Since module_init was not in use by this code, the init ordering
remains unchanged with this commit.

We also delete the MODULE_LICENSE tag etc. since all that information
was (or is now) contained at the top of the file in the comments.
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

The Kconfig currently controlling compilation of this code is:

drivers/mfd/Kconfig:config AB8500_DEBUG
drivers/mfd/Kconfig:       bool "Enable debug info via debugfs"

...meaning that it currently is not being built as a module by anyone.

Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.

We explicitly disallow a driver unbind, since that doesn't have a
sensible use case anyway, and it allows us to drop the ".remove"
code for non-modular drivers.

Since module_init was not in use by this code, the init ordering
remains unchanged with this commit.

We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

The Kconfig currently controlling compilation of this code is:

drivers/mfd/Kconfig:config AB8500_CORE
drivers/mfd/Kconfig:    bool "ST-Ericsson AB8500 Mixed Signal Power Management chip"

...meaning that it currently is not being built as a module by anyone.

Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.

We explicitly disallow a driver unbind, since that doesn't have a
sensible use case anyway, and it allows us to drop the ".remove"
code for non-modular drivers.

Since module_init was not in use by this code, the init ordering
remains unchanged with this commit.

We replace module.h with moduleparam.h ; the latter since this file
was implicitly relying on getting it.

We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

The Kconfig currently controlling compilation of this code is:

drivers/mfd/Kconfig:config AB3100_CORE
drivers/mfd/Kconfig:    bool "ST-Ericsson AB3100 Mixed Signal Circuit core functions"

...meaning that it currently is not being built as a module by anyone.

Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.  In doing
so, the debugfs unregister fcn becomes unused so we remove it too.

We explicitly disallow a driver unbind, since that doesn't have a
sensible use case anyway, and it allows us to drop the ".remove"
code for non-modular drivers.

Since module_init was not in use by this code, the init ordering
remains unchanged with this commit.

Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.

We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Trivial spelling mistake fixes in dev_err message.
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

No need to use irq_create_mapping (although there is no issue with
doing so) when we are only looking up an existing mapping. Just to
streamline things a little and make the code a little more clear
change some calls from irq_create_mapping to irq_find_mapping.
Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

The kernel WARNs and then crashes today if wm8994_device_init() fails
after calling devm_regulator_bulk_get().

That happens because there are multiple devices involved here and the
order in which managed resources are freed isn't correct.

The regulators are added as children of wm8994->dev.  Whereas,
devm_regulator_bulk_get() receives wm8994->dev as the device, though it
gets the same regulators which were added as children of wm8994->dev
earlier.

During failures, the children are removed first and the core eventually
calls regulator_unregister() for them. As regulator_put() was never done
for them (opposite of devm_regulator_bulk_get()), the kernel WARNs at

	WARN_ON(rdev->open_count);

And eventually it crashes from debugfs_remove_recursive().

Fix the kernel warnings and crashes by using regulator_bulk_get()
instead of devm_regulator_bulk_get() and explicitly freeing the supplies
in exit paths.

Tested on Exynos 5250, dual core ARM A15 machine.
Signed-off-by: NViresh Kumar <viresh.kumar@linaro.org>
Acked-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

mach/hardware.h is needed on C source code side, not header.
And struct davinci_vc is duplicated definition.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Remove the trailing spaces on the register default lines to
stop checkpatch complaining.
Signed-off-by: NRichard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

When building for X86 using COMPILE_TEST we get this warning:

../drivers/mfd/sun4i-gpadc.c: In function ‘sun4i_gpadc_probe’:
../drivers/mfd/sun4i-gpadc.c:110:10: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]

Since an integer and a pointer are difference sizes on 64bit architectures.

Convert to case to a long instead.
Signed-off-by: NLee Jones <lee.jones@linaro.org>

The i2c subsys does not load modules by compatible, only by
i2c-id, with e.g. a modalias of: "i2c:axp209".

Populate the axp20x_i2c_id[] table with supported ids, so that
module auto-loading will work.
Reported-by: NDennis Gilmore <dennis@ausil.us>
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Acked-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>