Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Fixes module unload+reload on Dell M4500, where the "normal" registers
get reset to 0.
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

When selecting the native mode for a display we weren't taking into account
whether or not it was actually supported on that particular output.

This patch modifies our native mode selection to run all modes through
mode_valid() first.
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

It was once assumed that all G8x had dual-link TMDS everywhere, this isn't
actually the case - especially considering passive DP->DVI converters and
some HDMI connectors only support single-link.
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

This resulted in accidently switching off the eDP panel on certain laptops
since the default state in the GPIO table was off.

Fixes rh#582621
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

We totally fail at detecting un-POSTed chipsets prior to G80.  This commit
changes the pre-G80 POST detection to read the programmed horizontal total
from CRTC 0, and assume the card isn't POSTed if it's 0.

NVIDIA use some other heuristics more similar to what we do on G80, but I
wasted quite a long time trying to figure out the exact specifics of what
they do so we can try this for a bit instead.
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

This will be useful for computing GPU-CPU latency, including
GL_ARB_timer_query extension.
Signed-off-by: NMarcin Kościelnicki <koriakin@0x04.net>
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

- This isn't triggered yet on a normal kernel, because it still does a VT
switch, but it seemed like a good idea to fix this now.
Tested-by: NMaxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: NMaarten Maathuis <madman2003@gmail.com>
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Mutliple issues.  INIT_ZM_I2C_BYTE/INIT_I2C_BYTE didn't even try and
use the register value, and all the handlers were using the wrong
slave address.
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

It appears to be meant to reference the second "default index".
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

We may not have parsed the entry yet if the i2c_index is for an i2c bus
that's not referenced by a DCB encoder.

This could be done oh so much more nicely, except we have to care about
prehistoric DCB tables too, and they make life painful.
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Some handlers don't report specific errors, but we still *really* want to
know if we failed to parse a complete init table.
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

We really want to be able to distinguish between INIT_DONE and an actual
error sometimes.  This commit fixes up several lazy "return 0;" to be
actual error codes, and explicitly reserves "0" as "success, but stop
parsing this table".
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

There appears to be some kind of switch on certain chips to control whether
the DP auxch or traditional i2c bus will be operational on a connector,
this commit hopefully fixes nouveau to do the right thing.

Likely only relevent on chips with DP outputs.
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

I actually thought these were gone already when the initial commit was
done.. I guess not!
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Signed-off-by: NMarcin Kościelnicki <koriakin@0x04.net>
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Signed-off-by: NMarcin Kościelnicki <koriakin@0x04.net>
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Reported-by: Dan Carpenter
Signed-off-by: NDave Airlie <airlied@redhat.com>

- Use radeon hpd enum consistently (in both hotplug and dp)
- Legacy r100 with DVI should be HPD_1 not NONE
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Some LVDS connectors don't have a ddc bus, so reset the
ddc bus to invalid before parsing the next connector
to avoid using stale ddc bus data.  Should fix
fdo bug 28164.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: NDave Airlie <airlied@redhat.com>

The current initialisation code probes 'unsupported' AGP devices
simply by calling its own probe function.  It does not lock these
devices or even check whether another driver is already bound to
them.

We must use the device core to manage this.  So if the specific
device id table didn't match anything and agp_try_unsupported=1,
switch the device id table and call driver_attach() again.
Signed-off-by: NBen Hutchings <ben@decadent.org.uk>
Signed-off-by: NDave Airlie <airlied@redhat.com>

SIS 760 is listed in the device tables for both amd64-agp and sis-agp.
amd64-agp is apparently preferable since it has workarounds for some
BIOS misconfigurations that sis-agp doesn't handle.
Signed-off-by: NBen Hutchings <ben@decadent.org.uk>
Signed-off-by: NDave Airlie <airlied@redhat.com>

* anholt/drm-intel-next: (515 commits)
  drm/i915: Fix out of tree builds
  drm/i915: move fence lru to struct drm_i915_fence_reg
  drm/i915: don't allow tiling changes on pinned buffers v2
  drm/i915: Be extra careful about A/D matching for multifunction SDVO
  drm/i915: Fix DDC bus selection for multifunction SDVO
  drm/i915: cleanup mode setting before unmapping registers
  drm/i915: Make fbc control wrapper functions
  drm/i915: Wait for the GPU whilst shrinking, if truly desperate.
  drm/i915: Use spatio-temporal dithering on PCH
  [MTD] Remove zero-length files mtdbdi.c and internal.ho
  pata_pcmcia / ide-cs: Fix bad hashes for Transcend and kingston IDs
  libata: Fix several inaccuracies in developer's guide
  slub: Fix bad boundary check in init_kmem_cache_nodes()
  raid6: fix recovery performance regression
  KEYS: call_sbin_request_key() must write lock keyrings before modifying them
  KEYS: Use RCU dereference wrappers in keyring key type code
  KEYS: find_keyring_by_name() can gain access to a freed keyring
  ALSA: hda: Fix 0 dB for Packard Bell models using Conexant CX20549 (Venice)
  ALSA: hda - Add quirk for Dell Inspiron 19T using a Conexant CX20582
  ALSA: take tu->qlock with irqs disabled
  ...

print an error if these fail.
Signed-off-by: NDave Airlie <airlied@redhat.com>

This patch is a combination of the previous two profile
patches, but without the index bugs.  It cleans up and
fixes some issues with pm profile setup on r6xx chips.
Some tables have different orderings for the power states,
also, r600 only has 1 clock mode per power state. On
desktop cards there are no battery modes, so the low and high
power states are the same.  For the low profile case, choose
the lower clock mode.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

- Separate dynpm and profile based power management methods.  You can select the pm method
  by echoing the selected method ("dynpm" or "profile") to power_method in sysfs.
- Expose basic 4 profile in profile method
  "default" - default clocks
  "auto" - select between low and high based on ac/dc state
  "low" - DC, low power mode
  "high" - AC, performance mode
  The current base profile is "default", but it should switched to "auto" once we've tested
  on more systems.  Switching the state is a matter of echoing the requested profile to
  power_profile in sysfs.  The lowest power states are selected automatically when dpms turns
  the monitors off in all states but default.
- Remove dynamic fence-based reclocking for the moment.  We can revisit this later once we
  have basic pm in.
- Move pm init/fini to modesetting path.  pm is tightly coupled with display state.  Make sure
  display side is initialized before pm.
- Add pm suspend/resume functions to make sure pm state is properly reinitialized on resume.
- Remove dynpm module option.  It's now selectable via sysfs.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

The lowest power states often cause display problems, so only enable
them when all displays are off.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

GUI idle interrupts don't seem to work terribly well on r500 and earlier,
so let's use a fence instead.
Signed-off-by: NMatthew Garrett <mjg@redhat.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

We need to handle the ring while we've already locked it, so split out
the allocation and commit functions in order to allow them to be used.
Signed-off-by: NMatthew Garrett <mjg@redhat.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>