- 23 5月, 2009 1 次提交
-
-
由 Ivo van Doorn 提交于
IEEE80211_CONF_CHANGE_BEACON_INTERVAL was deprecated a month ago, it is about time to remove all usage from the rt2x00 drivers and use the correct beacon interval configuration through the bss_info structure. Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 07 5月, 2009 1 次提交
-
-
由 Johannes Berg 提交于
The config_interface method is a little strange, it contains the BSSID and beacon updates, while bss_info_changed contains most other BSS information for each interface. This patch removes config_interface and rolls all the information it previously passed to drivers into bss_info_changed. Signed-off-by: NJohannes Berg <johannes@sipsolutions.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 23 4月, 2009 1 次提交
-
-
由 Ivo van Doorn 提交于
pci_dev->irq and pci_name(pci_dev) access should be limited to rt2x00pci only. This is more generic and allows a rt2x00 pci driver to be controlled as PCI device but also as platform driver (needed for rt2800pci SoC support). Signed-off-by: NFelix Fietkau <nbd@openwrt.org> Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 28 2月, 2009 1 次提交
-
-
由 Ivo van Doorn 提交于
The only way rf_write() can be called with word 0 is when the user sends the wrong word index through debugfs. However the values which are send through debugfs are validated using the RF_BASE and RF_SIZE macro values, the most logical solution is to increase RF_BASE with 4 and decrease RF_SIZE with 4 (RF_SIZE has always been 1 word too big) Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 10 2月, 2009 1 次提交
-
-
由 Ivo van Doorn 提交于
provide rt2x00lib the possibility to kill a particular TX queue. This can be useful when disabling the radio, but more importantly will allow beaconing to be disabled when mac80211 requests this (during scanning for example) Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 30 1月, 2009 7 次提交
-
-
由 Ivo van Doorn 提交于
When the led mode is asus, the activity led mode must be registered otherwise the second LED will not be enabled. Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Ivo van Doorn 提交于
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Andrew Price 提交于
Add a check for LED_MODE_DEFAULT so that we use the link LED for rt2400 and rt2500 devices. Signed-off-by: NAndrew Price <andy@andrewprice.me.uk> Acked-by: NIvo van Doorn <IvDoorn@gmail.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Johannes Berg 提交于
This modifies hardware flags for powersave to support three different flags: * IEEE80211_HW_SUPPORTS_PS - indicates general PS support * IEEE80211_HW_PS_NULLFUNC_STACK - indicates nullfunc sending in software * IEEE80211_HW_SUPPORTS_DYNAMIC_PS - indicates dynamic PS on the device It also adds documentation for all this which explains how to set the various flags. Additionally, it fixes a few things: * a spot where && was used to test flags * enable CONF_PS only when associated again Signed-off-by: NJohannes Berg <johannes@sipsolutions.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Ivo van Doorn 提交于
Restrict drivers to only access link_qual structure during link tuning. The contents of these fields are for the drivers and all fields are allowed to be changed to values the driver considers correct. This means that some fields need to be moved outside of this structure to restrict access only to rt2x00link itself. This allows some code to be moved outside of the rt2x00.h header and into rt2x00link.c. Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Ivo van Doorn 提交于
The link_tuner() function will always call bbp_read() at the start of the function. Because this is an indirect register access has some costs attached to it (especially for USB hardware). We already store the value read from the register into the vgc_level value inside the link structure. Instead of reading from the register we can read that field directly and base the tuner on that value. This reduces the time the registers are locked with the csr_mutex and speeds up the link_tuner processing. Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Ivo van Doorn 提交于
Listen to IEEE80211_CONF_PS to determine if the device should drop into powersaving mode. This feature depends on the dynamic power save functionality in mac80211. Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 26 11月, 2008 1 次提交
-
-
由 Ivo van Doorn 提交于
All code which accessed indirect registers was similar in respect to the for-loop, the given timeout, etc. Move it into a seperate function, which for PCI drivers can be moved into rt2x00pci. This allows us to cleanup the cleanup the code further by removing the goto statementsand making the codepath look a bit nicer. Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 22 11月, 2008 3 次提交
-
-
由 Ivo van Doorn 提交于
Indirect registers require multiple calls to the CSR register in order to access the indirect registers. This must be protected under a lock to prevent race conditions which could cause invalid data to be returned when reading from the indirect register or silent failures when writing data to the indirect register. USB drivers where already protected under a mutex, so rename the mutex and make PCI drivers use the mutex as well. This now means that BBP and RF registers are no longer accessible in interrupt context. That is not a bad situation since the slow behavior of accessing those registers means we don't _want_ to access them in interrupt context either. Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Ivo van Doorn 提交于
We can optimize get_duration and get_duration_res by making them a macro. They are really simple calculation handlers so this doesn't matter much. Often (especially in rt2400pci and rt2500pci, the arguments are hardcoded, and the result value is passed into other hardcoded values. By making the functions a macro GCC can optimize the entire thing much better. Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Ivo van Doorn 提交于
Merge the callback functions init_txentry() and init_rxentry(). This makes life in rt2x00lib a lot simpler and we can cleanup several functions. rt2x00pci contained "fake" FIELD definitions for descriptor words. This is not flexible since it assumes the driver will always have the same field to indicate if a driver is available or not. This should be dependent on the driver, and we should add a callback function for this. Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 11 11月, 2008 2 次提交
-
-
由 Ivo van Doorn 提交于
Move calculation of CSR register offset into rt2x00debug.c and remove the wrapper functions from each individual driver. (Except rt2500usb, which still needs to wrap for the different value type argument). Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Ivo van Doorn 提交于
Implement latest changed from mac80211 configuration handling to optmize configuration handling in rt2x00. * Remove set_retry_limit callback function, handled through config() * Move config_antenna to its own callback function, it isn't handled by mac80211 anymore * Use IEEE80211_CONF_CHANGED_* flags and remove manual checks * Removed deprecated short slot setting through config() and put it in config_erp() through which mac80211 now configures it * Remove config_phymode() and move contents to config_erp() since it only managed the basic rates which is now determined by mac80211 through config_erp(). Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 01 11月, 2008 1 次提交
-
-
由 Johannes Berg 提交于
Instead of having a separate callback, use the HW config callback with a new flag to change retry limits. Signed-off-by: NJohannes Berg <johannes@sipsolutions.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 28 10月, 2008 1 次提交
-
-
由 Johannes Berg 提交于
This converts pretty much everything to print_mac. There were a few things that had conflicts which I have just dropped for now, no harm done. I've built an allyesconfig with this and looked at the files that weren't built very carefully, but it's a huge patch. Signed-off-by: NJohannes Berg <johannes@sipsolutions.net> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 12 9月, 2008 2 次提交
-
-
由 Ivo van Doorn 提交于
There isn't really a good reason to have the LED configuration options selectable per driver, lets make it default 'y' and make it depend on the NEW_LEDS and LEDS_CLASS interface. Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Ivo van Doorn 提交于
RFKILL should be enabled for _all_ hardware whether or not they feature a rfkill button or not. Remove driver specific RFKILL configuration options and make the rt2x00lib version depend on CONFIG_RFKILL and defaulting to 'y' to make sure it will always be enabled when RFKILL was enabled. This also fixes some bugs where RFKILL wasn't initialized and didn't respond to RFKILL key presses. Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 30 8月, 2008 1 次提交
-
-
由 Ivo van Doorn 提交于
Some of the flags should be accessed atomically to prevent race conditions. The flags that are most important are those that can change often and indicate the actual state of the device, queue or queue entry. The big flag rename was done to move all state flags to the same naming type as the other rt2x00dev flags and made sure all places where the flags were used were changed. ;) Thanks to Stephen for most of the queue flags updates, which fixes some of the most obvious consequences of the race conditions. Among those the notorious: rt2x00queue_write_tx_frame: Error - Arrived at non-free entry in the non-full queue 0. rt2x00queue_write_tx_frame: Error - Arrived at non-free entry in the non-full queue 0. rt2x00queue_write_tx_frame: Error - Arrived at non-free entry in the non-full queue 0. Signed-off-by: NStephen Blackheath <tramp.enshrine.stephen@blacksapphire.com> Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 23 8月, 2008 1 次提交
-
-
由 Ivo van Doorn 提交于
Channel information which is read from EEPROM should be read into an array containing per-channel information. This removes the requirement of multiple arrays and makes the channel handling a bit cleaner and easier to expand. Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 15 7月, 2008 2 次提交
-
-
由 Ivo van Doorn 提交于
With the new beacon handling from mac80211 we can reorganize the beacon handling in rt2x00 as well. This patch will move the function to the TX handlers, and move all duplicate code into rt2x00queue.c. After this change the descriptor helper functions from rt2x00queue.c no longer need to be exported outside of rt2x00lib and can be declared static. Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Johannes Berg 提交于
This patch changes mac80211's beacon configuration handling to never pass skbs to the driver directly but rather always require the driver to use ieee80211_beacon_get(). Additionally, it introduces "change flags" on the config_interface() call to enable drivers to figure out what is changing. Finally, it removes the beacon_update() driver callback in favour of having IBSS beacon delivered by ieee80211_beacon_get() as well. Signed-off-by: NJohannes Berg <johannes@sipsolutions.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 10 7月, 2008 1 次提交
-
-
由 Ivo van Doorn 提交于
As soon as init_registers() was called, the rt2400/rt2500 would start raising beacondone interrupts. Since this is highly premature since no beacons were provided yet, we should initialize the synchronization register to 0. This will make all drivers initialize it to 0 regardless if they are raising beacondone interrupts or not, since it only makes sense to have it completely disabled. Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 09 7月, 2008 1 次提交
-
-
由 Ivo van Doorn 提交于
rt2400 is the only currently available rt2x00 driver which supports reporting of the RX end time for frames. Since mac80211 uses this information for IBSS syncing, it is important that it is being reported. v2: Complement 32 bits of RX timestamp with upper 32bits from TSF Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 27 6月, 2008 3 次提交
-
-
由 Ivo van Doorn 提交于
With a bit of code moving to rt2x00lib within the TX and RX paths we can now remove a lot of EXPORT_SYMBOL_GPL() statements. This cleans up the interface between rt2x00lib and the drivers and has the additional benefit that rt2x00pci and rt2x00usb are trimmed down in size as well since they have less to do. Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Gertjan van Wingerde 提交于
The current PCI drivers require a lot of pre-allocated DMA buffers. Reduce this by using dynamically mapped skb's (using pci_map_single) instead of the pre- allocated DMA buffers that are allocated at device start-up time. At the same time move common RX path code into rt2x00lib from rt2x00pci and rt2x00usb, as the RX paths now are now almost the same. Signed-off-by: NGertjan van Wingerde <gwingerde@kpnplanet.nl> Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Gertjan van Wingerde 提交于
At the same time clean up the device administration a bit, by storing a pointer to struct device instead of a void pointer that is dependent on the type of device. The normal PCI and USB subsystem provided macros can be used to convert the device pointer to the right type. This makes the rt2x00 driver a bit more type-safe. Signed-off-by: NGertjan van Wingerde <gwingerde@kpnplanet.nl> Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 15 6月, 2008 4 次提交
-
-
由 Gertjan van Wingerde 提交于
The data and data_len fields aren't really necessary in struct skb_frame_desc, as they can be deduced from the skb itself. Signed-off-by: NGertjan van Wingerde <gwingerde@kpnplanet.nl> Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Ivo van Doorn 提交于
TX queues shouldn't be kicked after each frame that is put into the queue. This could cause problems during RTS and CTS-to-self as well as with fragmentation. In all those cases you want all frames to be send out in a single burst. Off course we shouldn't let the queue fill up entirely, thus we introduce a 10% threshold which, when reached, will force the frames to be send out regardless of the frame. In addition we should prevent queues to become full in such a way that the tx() handler can fail. Instead of stopping the queue when it is full, we should stop it when it is below the threshold. Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Ivo van Doorn 提交于
Reduce code duplication by moving led structure initialization into a per-driver function. Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Ivo van Doorn 提交于
* Reduce goto usage * Mark if-statements which are true on hardware error unlikely() * Cleanup debug messages This makes the code look nicer and be better optimized since the chance of hardware errors should be very small. Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 22 5月, 2008 5 次提交
-
-
由 Johannes Berg 提交于
This patch converts mac80211 and all drivers to have transmit information and status in skb->cb rather than allocating extra memory for it and copying all the data around. To make it fit, a union is used where only data that is necessary for all steps is kept outside of the union. A number of fixes were done by Ivo, as well as the rt2x00 part of this patch. Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com> Signed-off-by: NJohannes Berg <johannes@sipsolutions.net> Acked-by: NDavid S. Miller <davem@davemloft.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Ivo van Doorn 提交于
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Ivo van Doorn 提交于
With the pending removal of the tx_control structure we can merge the RX and TX entry private data structure in advance. This will temporarily increase the required memory for the queue, but that overhead will only be limited. Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Ivo van Doorn 提交于
the rxdesc structure is properly memsetted before passed to the driver. This means we don't have to reinitialize the flags and dev_flags fields in the drivers again. This will prevent problems when the rxdone handler is adding flags in a earlier status and will make the code look nicer when we are adding more read attributes in the rxdone handler in the driver. Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Ivo van Doorn 提交于
Split rt2x00lib_write_tx_desc() up into a TX descriptor initializor and TX descriptor writer. This split is required to properly allow mac80211 to move its tx_control structure into the skb->cb array. The rt2x00queue_create_tx_descriptor() function will read all tx control information and convert it into a rt2x00 TX descriptor information structure. After that function is complete, we have all information we needed from the tx control structure and are free to start writing into the skb->cb array for our own purposes. rt2x00queue_write_tx_descriptor() will be in charge of really sending the TX descriptor to the hardware and kicking the TX queue. Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-