cd-gpios polarity should be changed to GPIO_ACTIVE_LOW and wp-gpios
should be changed to GPIO_ACTIVE_HIGH.
Otherwise, the SD may not work properly due to wrong polarity inversion
specified in DT after switch to common parsing function mmc_of_parse().
Signed-off-by: NDong Aisheng <aisheng.dong@freescale.com>
Acked-by: NShawn Guo <shawnguo@kernel.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Arrange the license text a bit to make it clear.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Acked-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

The Cubox has a recessed button between the HDMI and RJ-45 connectors
that wasn't mapped in the device tree, so I've mapped it to gpio-keys
BTN_0.
Signed-off-by: NGeorge Joseph <george.joseph@fairview5.com>
Tested-by: NGeorge Joseph <george.joseph@fairview5.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Update SolidRun iMX6 platforms DT descriptions to be dual-licensed.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Acked-by: NSascha Hauer <s.hauer@pengutronix.de>
Acked-by: NRabeeh Khoury <rabeeh@solid-run.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

All PWM users should explicitly enable the used PWMs in their device tree
so they can be disabled by default in imx6qdl.dtsi.
Signed-off-by: NPhilipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

Hummingboard has no over current hardware, so disable the over current
detection for both ports.

Cubox-i has over current hardware, so appropriately configure this.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

The configuration of the USB OTG is a platform configuration decision,
not a microsom decision.  Move this configuration out to the platform
level files.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

The front panel LED on the Cubox-i is driven by one of the iMX6 PWM
channels, and is wired between the PWM output and supply.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

Add the HDMI DT configuration for the SolidRun HummingBoard and Cubox-i.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

The spdif pinmux configuration must be connected to the spdif device to
take effect, not the spdif-transmitter.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Add support for the SolidRun Cubox-i devices.  This commit adds similar
basic support as the HummingBoard.  Further devices will be supported
in future patches.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Add support for the SolidRun HummingBoard.  This commit adds support for
the following interfaces on this board:

- Consumer Ir receiver
- S/PDIF output
- Both USB interfaces
- Gigabit Ethernet using AR8035
- UART port
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>