- 21 6月, 2016 22 次提交
-
-
由 Kejian Yan 提交于
As Hilink3 and Hilink4 use the same xge training and xge u adaptor for HNSv2, it needs to select which Hilink to be set before relative serdes being configed. The hilink_access_sel is the register to do that. Signed-off-by: NKejian Yan <yankejian@huawei.com> Signed-off-by: NYisen Zhuang <Yisen.Zhuang@huawei.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Qianqian Xie 提交于
The error info should be printed as "set mask to 64bit fail!" instead of "set mask to 32bit fail!" in dma_set_mask_and_coherent(). Signed-off-by: NQianqian Xie <xieqianqian@huawei.com> Signed-off-by: NYisen Zhuang <Yisen.Zhuang@huawei.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Qianqian Xie 提交于
The driver uses devm_ioremap_resource, it will unmap the map automatically, remove the unnecessary the resource free. Signed-off-by: NQianqian Xie <xieqianqian@huawei.com> Reported-by: NKefeng Wang <wangkefeng.wang@huawei.com> Signed-off-by: NYisen Zhuang <Yisen.Zhuang@huawei.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Qianqian Xie 提交于
The annotation info for hns_nic_reset_subtask() should be "for resetting subtask" instead of "for resetting suntask". Signed-off-by: NQianqian Xie <xieqianqian@huawei.com> Signed-off-by: NYisen Zhuang <Yisen.Zhuang@huawei.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Kejian Yan 提交于
HNS receives a packet without doing anything, but it should call skb_reset_mac_header() to initialize the header before using eth_hdr(). Fixes: 0d6b425aSigned-off-by: NKejian Yan <yankejian@huawei.com> Signed-off-by: NYisen Zhuang <Yisen.Zhuang@huawei.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Qianqian Xie 提交于
For service port, hns dsaf v1 support to close tx_pause. However, the port will be invalid when it run command ethtool to close tx_pause. This patch will fix it. Signed-off-by: NQianqian Xie <xieqiaqian@huawei.com> Signed-off-by: NYisen Zhuang <Yisen.Zhuang@huawei.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Qianqian Xie 提交于
The bit fileds of PPE reset register are different between HNS v1 and HNS v2, but the current procedure just only match HNS v1. Here is a patch to fix it. Signed-off-by: NKejian Yan <yankejian@huawei.com> Signed-off-by: NQianqian Xie <xieqianqian@huawei.com> Signed-off-by: NYisen Zhuang <Yisen.Zhuang@huawei.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 David S. Miller 提交于
Vivien Didelot says: ==================== net: dsa: mv88e6xxx: probe compatible This patchset factorizes the legacy and new SMI probing and abstracts the switch register accesses. This simplifies adding support for new chips or alternative register accesses. This will allow us to use a compatible chip info to describe how to access the SMI device and its switch ID register at probe time. For the legacy probe, we fix the compatible info to 88E6085. For the MDIO probe, we will use the compatible info from the device node data. All patches are reviewed. Changes since v4: - fix debug printing (was 'val' instead of '*val') Changes since v3 [3]: - better register access abstraction using the chip structure Changes since v2 [2]: - do not guess compatible model in legacy probe - add low level SMI API using a chip structure - allocate before probe and detection - add 3 cosmetic patches Changes since v1 [1]: - merge style fix from Ben Dooks - add Acked-by/Reviewed-by tags - drop one compatible string per model - detect the SMI device based on the compatible info - add an SMI ops structure [1] https://lkml.org/lkml/2016/6/8/1201 [2] https://lkml.org/lkml/2016/6/14/671 [3] https://lkml.org/lkml/2016/6/17/995 ==================== Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Vivien Didelot 提交于
When the SMI address of the switch chip is zero, the chip assumes to be the only one on the SMI master bus and thus responds to all its known SMI devices addresses (port registers, Global2, etc.) When its SMI address is not zero, some chips (e.g. 88E6352) use an indirect access through two SMI Command and Data registers. Other models (e.g. 88E6060) using less than 16 internal SMI addresses always use a direct access. Add a capability flag to describe chips supporting the (indirect) Multi-chip Addressing Mode, and a low-level API to access the registers via SMI. Other accesses (like Ethernet management frames) may be added later. Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com> Reviewed-by: NAndrew Lunn <andrew@lunn.ch> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Vivien Didelot 提交于
The switch ID is located at address 0x3 of every Port Registers bank. But not all Marvell switches have their Port Registers SMI Addresses starting at 0x10. 88E6060 starts at 0x8 and 88E6390 starts at 0x0. Add this data in the info structure and use it in the detection code. Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com> Reviewed-by: NAndrew Lunn <andrew@lunn.ch> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Vivien Didelot 提交于
After allocating the chip structure, pass it a compatible info pointer. The compatible info structure will be used later to describe how to access the switch registers and where to read the switch ID. For the standard MDIO probe, get it from the device node data. For the legacy DSA driver probing, pass it the 88E6085 info. Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com> Reviewed-by: NAndrew Lunn <andrew@lunn.ch> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Vivien Didelot 提交于
Extract the common detection code which assigns the info structure to the chip given the read switch ID. Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com> Reviewed-by: NAndrew Lunn <andrew@lunn.ch> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Vivien Didelot 提交于
Add an helper function to isolate SMI specific assignments and checks. This function will later help choosing the different SMI accesses based of the compatible info. Since the chip structure is already allocated in the legacy probe, use the mv88e6xxx_reg_read access routine instead of __mv88e6xxx_reg_read. Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com> Reviewed-by: NAndrew Lunn <andrew@lunn.ch> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Vivien Didelot 提交于
Add an helper function to allocate the chip structure at the beginning of the probe functions. It will be used to initialize the SMI access. Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com> Reviewed-by: NAndrew Lunn <andrew@lunn.ch> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Vivien Didelot 提交于
The chip smi_mutex mutex is used to protect the access to the internal switch registers, not only the Multi-chip Addressing Mode, as commented. Since we will isolate SMI-specific pieces of code, avoid the confusion now by renaming smi_mutex to reg_lock. No functional changes here. Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com> Reviewed-by: NAndrew Lunn <andrew@lunn.ch> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Vivien Didelot 提交于
The mv88e6xxx_table array and the mv88e6xxx_lookup_info function are static, so remove the table and size arguments from the lookup function. Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com> Reviewed-by: NAndrew Lunn <andrew@lunn.ch> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Vivien Didelot 提交于
Use the optional variant to get the reset GPIO line, instead of checking for the -ENOENT error. Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com> Reviewed-by: NAndrew Lunn <andrew@lunn.ch> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Vivien Didelot 提交于
The mixed assignments, allocations and registrations in the probe code make it hard to follow the logic and figure out what is DSA or chip specific. Extract the struct dsa_switch related code in a simple mv88e6xxx_register_switch helper function. For symmetry in the code, add a mv88e6xxx_unregister_switch function. Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com> Reviewed-by: NAndrew Lunn <andrew@lunn.ch> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Vivien Didelot 提交于
The MDIO device probe and remove functions are respectively incrementing and decrementing the bus refcount themselves. Since these bus level actions are out of the device scope, remove them. Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com> Acked-by: NAndrew Lunn <andrew@lunn.ch> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Vivien Didelot 提交于
In the MDIO probing function, dev is already assigned to &mdiodev->dev and np is already assigned to mdiodev->dev.of_node, so use them. Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com> Reviewed-by: NAndrew Lunn <andrew@lunn.ch> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Vivien Didelot 提交于
The chip->ds and ds->slave_mii_bus assignments are common to both legacy and new MDIO probing and are already done in the later setup code. Remove the duplicated assignments from the MDIO probing code. Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com> Reviewed-by: NAndrew Lunn <andrew@lunn.ch> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Vivien Didelot 提交于
This patch fixes 5 style problems reported by checkpatch: WARNING: suspect code indent for conditional statements (8, 24) #492: FILE: drivers/net/dsa/mv88e6xxx.c:492: + if (phydev->link) + reg |= PORT_PCS_CTRL_LINK_UP; CHECK: Logical continuations should be on the previous line #1318: FILE: drivers/net/dsa/mv88e6xxx.c:1318: + oldstate == PORT_CONTROL_STATE_FORWARDING) + && (state == PORT_CONTROL_STATE_DISABLED || CHECK: multiple assignments should be avoided #1662: FILE: drivers/net/dsa/mv88e6xxx.c:1662: + vlan->vid_begin = vlan->vid_end = next.vid; WARNING: line over 80 characters #2097: FILE: drivers/net/dsa/mv88e6xxx.c:2097: + const struct switchdev_obj_port_vlan *vlan, WARNING: suspect code indent for conditional statements (16, 32) #2734: FILE: drivers/net/dsa/mv88e6xxx.c:2734: + if (mv88e6xxx_6352_family(ps) || mv88e6xxx_6351_family(ps) || [...] + reg |= PORT_CONTROL_EGRESS_ADD_TAG; total: 0 errors, 3 warnings, 2 checks, 3805 lines checked It also rebases and integrates changes sent by Ben Dooks [1]: The driver has a number of functions that are not exported or declared elsewhere, so make them static to avoid the following warnings from sparse: drivers/net/dsa/mv88e6xxx.c:113:5: warning: symbol 'mv88e6xxx_reg_read' was not declared. Should it be static? drivers/net/dsa/mv88e6xxx.c:167:5: warning: symbol 'mv88e6xxx_reg_write' was not declared. Should it be static? drivers/net/dsa/mv88e6xxx.c:231:5: warning: symbol 'mv88e6xxx_set_addr' was not declared. Should it be static? drivers/net/dsa/mv88e6xxx.c:367:6: warning: symbol 'mv88e6xxx_ppu_state_init' was not declared. Should it be static? drivers/net/dsa/mv88e6xxx.c:3157:5: warning: symbol 'mv88e6xxx_phy_page_read' was not declared. Should it be static? drivers/net/dsa/mv88e6xxx.c:3169:5: warning: symbol 'mv88e6xxx_phy_page_write' was not declared. Should it be static? drivers/net/dsa/mv88e6xxx.c:3583:26: warning: symbol 'mv88e6xxx_switch_driver' was not declared. Should it be static? drivers/net/dsa/mv88e6xxx.c:3621:5: warning: symbol 'mv88e6xxx_probe' was not declared. Should it be static? [1] http://patchwork.ozlabs.org/patch/632708/Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com> Reviewed-by: NAndrew Lunn <andrew@lunn.ch> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 20 6月, 2016 4 次提交
-
-
由 Philippe Reynes 提交于
There are two generics functions phy_ethtool_{get|set}_link_ksettings, so we can use them instead of defining the same code in the driver. Signed-off-by: NPhilippe Reynes <tremyfr@gmail.com> Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Philippe Reynes 提交于
The private structure contain a pointer to phydev, but the structure net_device already contain such pointer. So we can remove the pointer phydev in the private structure, and update the driver to use the one contained in struct net_device. Signed-off-by: NPhilippe Reynes <tremyfr@gmail.com> Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Philippe Reynes 提交于
There are two generics functions phy_ethtool_{get|set}_link_ksettings, so we can use them instead of defining the same code in the driver. Signed-off-by: NPhilippe Reynes <tremyfr@gmail.com> Acked-by: NMans Rullgard <mans@mansr.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Philippe Reynes 提交于
The private structure contain a pointer to phydev, but the structure net_device already contain such pointer. So we can remove the pointer phydev in the private structure, and update the driver to use the one contained in struct net_device. Signed-off-by: NPhilippe Reynes <tremyfr@gmail.com> Acked-by: NMans Rullgard <mans@mansr.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 19 6月, 2016 6 次提交
-
-
由 David S. Miller 提交于
Eric Dumazet says: ==================== ipv6: better traceroute support in sit and gre In commit ca15a078 ("sit: generate icmpv6 error when receiving icmpv4 error"), Oussama Ghorbel added minimal support for SIT tunnels to generate ICMPv6 messages when receiving ICMPv4 messages. This patch series extends this to GRE tunnels. It also adds support for ICMPV6_TIME_EXCEED. Partial support for RFC 4884 is added, to forward ICMP Multi-part extensions eventually found in the ICMPv4 message. v2: replaced an overlapping memcpy() by memmove() ==================== Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Eric Dumazet 提交于
When receiving an ICMPv4 message containing extensions as defined in RFC 4884, and translating it to ICMPv6 at SIT or GRE tunnel, we need some extra manipulation in order to properly forward the extensions. This patch only takes care of Time Exceeded messages as they are the ones that typically carry information from various routers in a fabric during a traceroute session. It also avoids complex skb logic if the data_len is not a multiple of 8. RFC states : The "original datagram" field MUST contain at least 128 octets. If the original datagram did not contain 128 octets, the "original datagram" field MUST be zero padded to 128 octets. In practice routers use 128 bytes of original datagram, not more. Initial translation was added in commit ca15a078 ("sit: generate icmpv6 error when receiving icmpv4 error") Signed-off-by: NEric Dumazet <edumazet@google.com> Cc: Oussama Ghorbel <ghorbel@pivasoftware.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Eric Dumazet 提交于
ipgre_err() can call ip6_err_gen_icmpv6_unreach() for proper support of ipv4+gre+icmp+ipv6+... frames, used for example by traceroute/mtr. Signed-off-by: NEric Dumazet <edumazet@google.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Eric Dumazet 提交于
For better traceroute/mtr support for SIT and GRE tunnels, we translate IPV4 ICMP ICMP_TIME_EXCEEDED to ICMPV6_TIME_EXCEED We also have to translate the IPv4 source IP address of ICMP message to IPv6 v4mapped. Signed-off-by: NEric Dumazet <edumazet@google.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Eric Dumazet 提交于
We want to use this helper from GRE as well, so this is the time to move it in net/ipv6/icmp.c Also add a @nhs parameter, since SIT and GRE have different values for the header(s) to skip. Signed-off-by: NEric Dumazet <edumazet@google.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Eric Dumazet 提交于
SIT or GRE tunnels might want to translate an IPV4 address into a v4mapped one when translating ICMP to ICMPv6. This patch adds the parameter to icmp6_send() but does not change icmpv6_send() signature. Signed-off-by: NEric Dumazet <edumazet@google.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 18 6月, 2016 8 次提交
-
-
由 Philippe Reynes 提交于
There are two generics functions phy_ethtool_{get|set}_link_ksettings, so we can use them instead of defining the same code in the driver. Signed-off-by: NPhilippe Reynes <tremyfr@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Philippe Reynes 提交于
The private structure contain a pointer to phydev, but the structure net_device already contain such pointer. So we can remove the pointer phydev in the private structure, and update the driver to use the one contained in struct net_device. Signed-off-by: NPhilippe Reynes <tremyfr@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Wei Yongjun 提交于
Fixes the following sparse warnings: net/rds/tcp.c:59:5: warning: symbol 'rds_tcp_min_sndbuf' was not declared. Should it be static? net/rds/tcp.c:60:5: warning: symbol 'rds_tcp_min_rcvbuf' was not declared. Should it be static? Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn> Acked-by: NSowmini Varadhan <sowmini.varadhan@oracle.com> Acked-by: NSantosh Shilimkar <santosh.shilimkar@oracle.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Wei Yongjun 提交于
Remove including <linux/version.h> that don't need it. Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Wei Yongjun 提交于
Remove including <linux/version.h> that don't need it. Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 David S. Miller 提交于
Merge tag 'linux-can-next-for-4.8-20160617' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next Marc Kleine-Budde says: ==================== pull-request: can-next 2016-06-17 this is a pull request of 14 patches for net-next/master. Geert Uytterhoeven contributes a patch that adds a file patterns for CAN device tree bindings to MAINTAINERS. A patch by Alexander Aring fixes warnings when building without proc support. A patch by me improves the sample point calculation. Marek Vasut's patch converts the slcan driver to use CAN_MTU. A patch by William Breathitt Gray converts the tscan1 driver to use module_isa_driver. Two patches by Maximilian Schneider for the gs_usb driver fix coding style and add support for set_phys_id callback. 5 patches by Oliver Hartkopp add support for CANFD to the bcm. And finally two patches by Ramesh Shanmugasundaram, which add support for the rcar_canfd driver. ==================== Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 David S. Miller 提交于
Ivan Khoronzhuk says: ==================== net: ethernet: ti: cpsw: delete rx_descs property There is no reason in rx_descs property because davinici_cpdma driver splits pool of descriptors equally between tx and rx channels. So, this patch series makes driver to use available number of descriptors for rx channels. ==================== Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Ivan Khoronzhuk 提交于
There is no reason to hold s/w dependent parameter in device tree. Even more, there is no reason in this parameter because davinici_cpdma driver splits pool of descriptors equally between tx and rx channels anyway. Acked-by: NRob Herring <robh@kernel.org> Signed-off-by: NIvan Khoronzhuk <ivan.khoronzhuk@linaro.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-