Amend the ab8500-usb driver to optionally take a pin control handle and
set the state of the pins to "default" on ab8500_usb_phy_enable and to
"sleep" on ab8500_usb_phy_disable.

The pinctrl handle is released on ab8500_usb_phy_disable because USB
pins are shared with ab8505_micro_usb_iddet driver.
Signed-off-by: NPatrice Chotard <patrice.chotard@st.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NFabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Fix last ab->phy.notifier call to use vbus_draw as notifier argument, as
that's used in ab8500_charger to control charging current.

Also drop a related TODO comment, and the additional
ux500_musb_set_vbus(musb, 0), as with this patch it was causing an
erratic behaviour of gadget ep0 state machine.
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NFabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

To prevent clock and regulator frameworks from complaining, only disable
the host or peripheral phy if they were enabled.
Reported-by: NSakethram Bommisetti <sakethram.bommisetti@stericsson.com>
Signed-off-by: NMian Yousaf Kaukab <mian.yousaf.kaukab@stericsson.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NFabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Add ab8500_usb_regulator_{enable,disable} functions to control USB phy
regulators on corresponding ab8500_usb_phy_{enable,disable} events.

This contains some workaround and optimization for specific AB8500
versions.
Signed-off-by: NMian Yousaf Kaukab <mian.yousaf.kaukab@stericsson.com>
Signed-off-by: NSakethram Bommisetti <sakethram.bommisetti@stericsson.com>
Signed-off-by: NPraveena Nadahally <praveen.nadahally@stericsson.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NFabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Split ab8500_usb_phy_ctrl into separate enable/disable functions to make
the code more linear and readable.
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NFabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Add initial regulator support to ab8500-usb by introducing necessary
devm_regulator_get().
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NFabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

AB8500 v2.0 has eye diagram issues when drawing more than 100mA from
VBUS.  Force charging current to 100mA in case of standard host.
Signed-off-by: NSakethram Bommisetti <sakethram.bommisetti@stericsson.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NFabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Set phy tuning values proposed by the hardware teams for AB8500 and
AB8505 to improve USB eye diagram performances.
Signed-off-by: NSakethram Bommisetti <sakethram.bommisetti@stericsson.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NFabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Convert local data allocation to devm_kzalloc and drop unnecessary fail
path code.
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NFabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Drop references to deprecated U5500 platform in driver comments.
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NFabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Use the newly introduced devm_ioremap_resource() instead of
devm_request_and_ioremap() which provides more consistent error handling.

devm_ioremap_resource() provides its own error messages; so all explicit
error messages can be removed from the failure code paths.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Remove all section annotations to fix the
following section mismatches:

>> WARNING: drivers/usb/gadget/pxa27x_udc.o(.text+0x597c): Section mismatch in
reference from the function .pxa_udc_probe() to the function
.init.text:.udc_init_data.constprop.11()
   The function .pxa_udc_probe() references
   the function __init .udc_init_data.constprop.11().
   This is often because .pxa_udc_probe lacks a __init
   annotation or the annotation of .udc_init_data.constprop.11 is wrong.
--
>> WARNING: drivers/usb/gadget/pxa27x_udc.o(.text+0x5a04): Section mismatch in
reference from the function .pxa_udc_probe() to the function
.init.text:.pxa_ep_setup()
   The function .pxa_udc_probe() references
   the function __init .pxa_ep_setup().
   This is often because .pxa_udc_probe lacks a __init
   annotation or the annotation of .pxa_ep_setup is wrong.
Reported-by: NFengguang Wu <fengguang.wu@intel.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

udc-core would leak 'udc' memory in some error
cases. Fix it by kfree()ing udc on error path.
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Enter IDMA_RESET only when the controller has been reset or
the device has been plugged in to or out from a host. In
IDMA_RESET, we should disable the corresponding PRD interrupt.
Also there is a redundant space eliminated.

fusb300_udc driver is tested on FARADAY platform a369 with
FUSB300 FPGA v1.8
Signed-off-by: NYuan-Hsin Chen <yhchen@faraday-tech.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

The final version of fusb300 controller adds EPSET0_STL_CLR
for clearing EP0 stall and also removes EPSET0_EPn_TX0BYTE.

fusb300_udc driver is tested on FARADAY platform a369 with
FUSB300 FPGA v1.8
Signed-off-by: NYuan-Hsin Chen <yhchen@faraday-tech.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Add CONFIG_PM_SLEEP to suspend/resume functions to fix the following
build warning when CONFIG_PM_SLEEP is not selected. This is because
sleep PM callbacks defined by SET_SYSTEM_SLEEP_PM_OPS are only used
when the CONFIG_PM_SLEEP is enabled. Unnecessary CONFIG_PM ifdefs
are removed.

drivers/usb/dwc3/core.c:682:12: warning: 'dwc3_suspend' defined but not used [-Wunused-function]
drivers/usb/dwc3/core.c:709:12: warning: 'dwc3_resume' defined but not used [-Wunused-function]
drivers/usb/dwc3/dwc3-omap.c:430:12: warning: 'dwc3_omap_suspend' defined but not used [-Wunused-function]
drivers/usb/dwc3/dwc3-omap.c:440:12: warning: 'dwc3_omap_resume' defined but not used [-Wunused-function]
drivers/usb/dwc3/dwc3-exynos.c:185:12: warning: 'dwc3_exynos_suspend' defined but not used [-Wunused-function]
drivers/usb/dwc3/dwc3-exynos.c:194:12: warning: 'dwc3_exynos_resume' defined but not used [-Wunused-function]
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

avoid reading fifo rxcount is zero of fifo is empty, hence
read fifo only if rxcount is non-zero
Signed-off-by: NRavi Babu <ravibabu@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

The musb controller uses single bit defintion for both reset and
babble events. The babble event is valid only when controller is
active a-host, and hence print the babble message only when the
controller is active a-host.
Signed-off-by: NRavi Babu <ravibabu@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

MUSB controller cannot work in DMA mode with misaligned buffers,
switching in PIO mode.

HCD core has hooks that allow to override the default DMA
mapping and unmapping routines for host controllers that have
special DMA requirements, such as alignment constraints.

It is observed that work in PIO mode is slow and it's better
to align buffers properly before passing them to MUSB

This increased throughput 80->120 MBits/s over musb@omap4 with
USB Gigabit Ethernet adapter attached.

Some ideas are taken from ehci-tegra.c
Signed-off-by: NRuslan Bilovol <ruslan.bilovol@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This patch adds the support for 'get_unmapped_area' in UVC gadget
which is called when the 'mmap' system call is executed on MMUless
architectures.
Signed-off-by: NBhupesh Sharma <bhupesh.sharma@st.com>
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>

This patch reworks the videobuffer management logic present in the UVC
webcam gadget and ports it to use the "more apt" videobuf2 framework for
video buffer management.

To support routing video data captured from a real V4L2 video capture
device with a "zero copy" operation on videobuffers (as they pass from
the V4L2 domain to UVC domain via a user-space application), we need to
support USER_PTR IO method at the UVC gadget side.

So the V4L2 capture device driver can still continue to use MMAP IO
method and now the user-space application can just pass a pointer to the
video buffers being dequeued from the V4L2 device side while queueing
them at the UVC gadget end. This ensures that we have a "zero-copy"
design as the videobuffers pass from the V4L2 capture device to the UVC
gadget.

Note that there will still be a need to apply UVC specific payload
headers on top of each UVC payload data, which will still require a copy
operation to be performed in the 'encode' routines of the UVC gadget.

This patch also addresses one issue found out while porting the UVC
gadget to videobuf2 framework:
	- In case the usb requests queued by the gadget get completed
	  with a status of -ESHUTDOWN (disconnected from host),
	  the queue of videobuf2 should be cancelled to ensure that the
	  application space daemon is not left in a state waiting for
	  a vb2 to be successfully absorbed at the USB side.
Signed-off-by: NBhupesh Sharma <bhupesh.sharma@st.com>
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>

This patch fixup below sparse errors

CHECK   ${RENESAS_USB}/common.c
${RENESAS_USB}/common.c:313:17: error: incompatible types in conditional expression (different base types)
${RENESAS_USB}/common.c:322:17: error: incompatible types in conditional expression (different base types)
${RENESAS_USB}/common.c:384:17: error: incompatible types in conditional expression (different base types)
${RENESAS_USB}/common.c:524:9: error: incompatible types in conditional expression (different base types)
${RENESAS_USB}/common.c:545:9: error: incompatible types in conditional expression (different base types)
${RENESAS_USB}/common.c:574:9: error: incompatible types in conditional expression (different base types)
${RENESAS_USB}/common.c:606:9: error: incompatible types in conditional expression (different base types)
${RENESAS_USB}/mod_gadget.c:233:28: warning: symbol 'req_clear_feature' was not declared. Should it be static?
${RENESAS_USB}/mod_gadget.c:274:28: warning: symbol 'req_set_feature' was not declared. Should it be static?
${RENESAS_USB}/mod_gadget.c:375:28: warning: symbol 'req_get_status' was not declared. Should it be static?

[ balbi@ti.com : added three sparse fixes to mod_gadget.c ]
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Using pdata to pass clock name is not correct.
Directly get clock from usb drivers.
Signed-off-by: NChao Xie <chao.xie@marvell.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

The origianl understanding of clock is wrong. The UDC controller
only have one clock input.
Passing clock name by pdata is wrong. The clock is defined by device
iteself.

Cc: Chao Xie <chao.xie@marvell.com>
Cc: Yu Xu <yuxu@marvell.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

The clock name will directly get by driver. Removing
the name from pdata.
Acked-by: NHaojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: NChao Xie <chao.xie@marvell.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

The clock name will directly get by driver. Removing
the name from pdata.
Acked-by: NHaojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: NChao Xie <chao.xie@marvell.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

The origianl understanding of clock is wrong. The EHCI controller
only have one clock input.
Passing clock name by pdata is wrong. The clock is defined by device
iteself.
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NChao Xie <chao.xie@marvell.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

The origianl understanding of clock is wrong. The OTG controller
only have one clock input.
Passing clock name by pdata is wrong. The clock is defined by device
iteself.
Signed-off-by: NChao Xie <chao.xie@marvell.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

The origianl understanding of clock is wrong. The UDC controller
only have one clock input.
Passing clock name by pdata is wrong. The clock is defined by device
iteself.
Signed-off-by: NChao Xie <chao.xie@marvell.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

On some platform configurations (like OMAP3+twl4030) it's the platform
code that enables VBUS, not OTG transceiver, so call vbus platform
callback instead, it will then call the transceiver if needed.

This fixes a use case where USB cable is plugged first and gadget
driver is loaded later after that.
Signed-off-by: NGrazvydas Ignotas <notasas@gmail.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

On USB_EVENT_ID event the musb glue enables VBUS by calling
omap2430_musb_set_vbus(musb, 1) that sets the session bit, but on
USB_EVENT_NONE reverse action is never made, and that breaks PM.

Disable VBUS on USB_EVENT_NONE to be sure musb session is ended
on cable unplug so that PM works.
Signed-off-by: NGrazvydas Ignotas <notasas@gmail.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

At least on pandora, STS_VBUS gets set even when VBUS is driven by twl
itself. Reporting VBUS in this case confuses OMAP musb glue and charger
driver, so check if OTG VBUS charge pump is on before reporting VBUS
event to avoid this problem.
Signed-off-by: NGrazvydas Ignotas <notasas@gmail.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

fix the following sparse warning:

drivers/usb/musb/ux500_dma.c:60:6: warning: symbol 'ux500_dma_callback' was not declared. Should it be static?
Signed-off-by: NFelipe Balbi <balbi@ti.com>

fix the following sparse warnings:

drivers/usb/gadget/mv_u3d_core.c:223:20: warning: context imbalance in 'mv_u3d_done' - unexpected unlock
drivers/usb/gadget/mv_u3d_core.c:1562:25: warning: context imbalance in 'mv_u3d_handle_setup_packet' - unexpected unlock

Note that the non-trivial sparse warnings
are left out of this commit due to lack of
HW to test:

drivers/usb/gadget/mv_u3d_core.c:906:42: warning: incorrect type in argument 2 (different address spaces)
drivers/usb/gadget/mv_u3d_core.c:906:42:    expected void [noderef] <asn:2>*<noident>
drivers/usb/gadget/mv_u3d_core.c:906:42:    got unsigned int *<noident>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

fix the following sparse warnings:

drivers/usb/gadget/mv_udc_core.c:1850:6: warning: symbol 'irq_process_reset' was not declared. Should it be static?
drivers/usb/gadget/mv_udc_core.c:247:9: warning: context imbalance in 'done' - unexpected unlock
drivers/usb/gadget/mv_udc_core.c:1692:25: warning: context imbalance in 'handle_setup_packet' - unexpected unlock

Note that there are still other sparse warnings
which aren't trivial to fix, so I left them out:

drivers/usb/gadget/mv_udc_core.c:848:34: warning: incorrect type in argument 1 (different address spaces)
drivers/usb/gadget/mv_udc_core.c:848:34:    expected void const volatile [noderef] <asn:2>*addr
drivers/usb/gadget/mv_udc_core.c:848:34:    got unsigned int *<noident>
drivers/usb/gadget/mv_udc_core.c:849:42: warning: incorrect type in argument 2 (different address spaces)
drivers/usb/gadget/mv_udc_core.c:849:42:    expected void volatile [noderef] <asn:2>*addr
drivers/usb/gadget/mv_udc_core.c:849:42:    got unsigned int *<noident>
Acked-by: NNeil Zhang <zhangwm@marvell.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

fix the following sparse warnings:

drivers/usb/gadget/pch_udc.c:1483:9: warning: context imbalance in 'complete_req' - unexpected unlock
drivers/usb/gadget/pch_udc.c:2408:28: warning: context imbalance in 'pch_udc_svc_control_out' - unexpected unlock
Signed-off-by: NFelipe Balbi <balbi@ti.com>

fix the following sparse warning:

drivers/usb/gadget/dummy_hcd.c:1912:12: warning: symbol 'usb3_bos_desc' was not declared. Should it be static?
Acked-by: NMichal Nazarewicz <mina86@mina86.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

fix the following sparse warnings:

drivers/usb/gadget/net2280.c:2063:13: warning: Using plain integer as NULL pointer
drivers/usb/gadget/net2280.c:2321:68: warning: Using plain integer as NULL pointer
drivers/usb/gadget/net2280.c:2349:68: warning: Using plain integer as NULL pointer
drivers/usb/gadget/net2280.c:2371:68: warning: Using plain integer as NULL pointer
Acked-by: NMichal Nazarewicz <mina86@mina86.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Fix the following sparse warnings:

drivers/usb/gadget/net2272.c:916:13: warning: Using plain integer as NULL pointer
drivers/usb/gadget/net2272.c:1624:9: warning: Using plain integer as NULL pointer
drivers/usb/gadget/net2272.c:1552:30: warning: right shift by bigger than source value

Note that the last warning is an actual bug,
since ep->dma is a one bit value which is
shifted by one bit in code.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

this driver compiles fine everywhere which
means we can use linux-next to compile it
for us frequently.

By dropping the arch dependency, we also
ensure driver writers don't add virtual
arch-depdencies to the driver by e.g. using
the wrong headers.

While at that, fix Marvell's USB3 PHY dependency,
that's the driver which depends on CPU_MM3, not
mv_u3d_core.
Signed-off-by: NFelipe Balbi <balbi@ti.com>