Skip to content

cloud-kernel
cloud-kernel

openanolis / cloud-kernel
1 年多 前同步成功

通知 160
Star 36
Fork 7
cloud-kernel
cloud-kernel
切换分支/标签
  1. 04 11月, 2015 15 次提交
  3. 02 11月, 2015 2 次提交
  5. 29 10月, 2015 3 次提交
    • C
      KVM: s390: use simple switch statement as multiplexer · 46b708ea
      由 Christian Borntraeger 提交于 
      We currently do some magic shifting (by exploiting that exit codes
are always a multiple of 4) and a table lookup to jump into the
exit handlers. This causes some calculations and checks, just to
do an potentially expensive function call.

Changing that to a switch statement gives the compiler the chance
to inline and dynamically decide between jump tables or inline
compare and branches. In addition it makes the code more readable.

bloat-o-meter gives me a small reduction in code size:

add/remove: 0/7 grow/shrink: 1/1 up/down: 986/-1334 (-348)
function                                     old     new   delta
kvm_handle_sie_intercept                      72    1058    +986
handle_prog                                  704     696      -8
handle_noop                                   54       -     -54
handle_partial_execution                      60       -     -60
intercept_funcs                              120       -    -120
handle_instruction                           198       -    -198
handle_validity                              210       -    -210
handle_stop                                  316       -    -316
handle_external_interrupt                    368       -    -368

Right now my gcc does conditional branches instead of jump tables.
The inlining seems to give us enough cycles as some micro-benchmarking
shows minimal improvements, but still in noise.
Signed-off-by: NChristian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: NCornelia Huck <cornelia.huck@de.ibm.com>
      46b708ea
    • C
      KVM: s390: drop useless newline in debugging data · 58c383c6
      由 Christian Borntraeger 提交于 
      the s390 debug feature does not need newlines. In fact it will
result in empty lines. Get rid of 4 leftovers.
Signed-off-by: NChristian Borntraeger <borntraeger@de.ibm.com>
Acked-by: NCornelia Huck <cornelia.huck@de.ibm.com>
      58c383c6
    • D
      KVM: s390: SCA must not cross page boundaries · c5c2c393
      由 David Hildenbrand 提交于 
      We seemed to have missed a few corner cases in commit f6c137ff
("KVM: s390: randomize sca address").

The SCA has a maximum size of 2112 bytes. By setting the sca_offset to
some unlucky numbers, we exceed the page.

0x7c0 (1984) -> Fits exactly
0x7d0 (2000) -> 16 bytes out
0x7e0 (2016) -> 32 bytes out
0x7f0 (2032) -> 48 bytes out

One VCPU entry is 32 bytes long.

For the last two cases, we actually write data to the other page.
1. The address of the VCPU.
2. Injection/delivery/clearing of SIGP externall calls via SIGP IF.

Especially the 2. happens regularly. So this could produce two problems:
1. The guest losing/getting external calls.
2. Random memory overwrites in the host.

So this problem happens on every 127 + 128 created VM with 64 VCPUs.

Cc: stable@vger.kernel.org # v3.15+
Acked-by: NChristian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: NDavid Hildenbrand <dahi@linux.vnet.ibm.com>
Signed-off-by: NChristian Borntraeger <borntraeger@de.ibm.com>
      c5c2c393
  7. 23 10月, 2015 18 次提交
    • M
      KVM: arm: Do not indent the arguments of DECLARE_BITMAP · 5fdf876d
      由 Michal Marek 提交于 
      Besides being a coding style issue, it confuses make tags:

ctags: Warning: include/kvm/arm_vgic.h:307: null expansion of name pattern "\1"
ctags: Warning: include/kvm/arm_vgic.h:308: null expansion of name pattern "\1"
ctags: Warning: include/kvm/arm_vgic.h:309: null expansion of name pattern "\1"
ctags: Warning: include/kvm/arm_vgic.h:317: null expansion of name pattern "\1"

Cc: kvmarm@lists.cs.columbia.edu
Signed-off-by: NMichal Marek <mmarek@suse.com>
Signed-off-by: NChristoffer Dall <christoffer.dall@linaro.org>
      5fdf876d
    • M
      arm64: kvm: restore EL1N SP for panic · db85c55f
      由 Mark Rutland 提交于 
      If we panic in hyp mode, we inject a call to panic() into the EL1N host
kernel. If a guest context is active, we first attempt to restore the
minimal amount of state necessary to execute the host kernel with
restore_sysregs.

However, the SP is restored as part of restore_common_regs, and so we
may return to the host's panic() function with the SP of the guest. Any
calculations based on the SP will be bogus, and any attempt to access
the stack will result in recursive data aborts.

When running Linux as a guest, the guest's EL1N SP is like to be some
valid kernel address. In this case, the host kernel may use that region
as a stack for panic(), corrupting it in the process.

Avoid the problem by restoring the host SP prior to returning to the
host. To prevent misleading backtraces in the host, the FP is zeroed at
the same time. We don't need any of the other "common" registers in
order to panic successfully.
Signed-off-by: NMark Rutland <mark.rutland@arm.com>
Acked-by: NMarc Zyngier <marc.zyngier@arm.com>
Cc: Christoffer Dall <christoffer.dall@linaro.org>
Cc: <kvmarm@lists.cs.columbia.edu>
Signed-off-by: NChristoffer Dall <christoffer.dall@linaro.org>
      db85c55f
    • C
      arm/arm64: KVM: Add tracepoints for vgic and timer · e21f0910
      由 Christoffer Dall 提交于 
      The VGIC and timer code for KVM arm/arm64 doesn't have any tracepoints
or tracepoint infrastructure defined.  Rewriting some of the timer code
handling showed me how much we need this, so let's add these simple
trace points once and for all and we can easily expand with additional
trace points in these files as we go along.

Cc: Wei Huang <wei@redhat.com>
Signed-off-by: NChristoffer Dall <christoffer.dall@linaro.org>
      e21f0910
    • C
      arm/arm64: KVM: Improve kvm_exit tracepoint · b5905dc1
      由 Christoffer Dall 提交于 
      The ARM architecture only saves the exit class to the HSR (ESR_EL2 for
arm64) on synchronous exceptions, not on asynchronous exceptions like an
IRQ.  However, we only report the exception class on kvm_exit, which is
confusing because an IRQ looks like it exited at some PC with the same
reason as the previous exit.  Add a lookup table for the exception index
and prepend the kvm_exit tracepoint text with the exception type to
clarify this situation.

Also resolve the exception class (EC) to a human-friendly text version
so the trace output becomes immediately usable for debugging this code.

Cc: Wei Huang <wei@redhat.com>
Signed-off-by: NChristoffer Dall <christoffer.dall@linaro.org>
      b5905dc1
    • P
      KVM: arm/arm64: Fix vGIC documentation · 952105ab
      由 Pavel Fedin 提交于 
      Correct some old mistakes in the API documentation:

1. VCPU is identified by index (using kvm_get_vcpu() function), but
   "cpu id" can be mistaken for affinity ID.
2. Some error codes are wrong.

  [ Slightly tweaked some grammer and did some s/CPU index/vcpu_index/
    in the descriptions.  -Christoffer ]
Signed-off-by: NPavel Fedin <p.fedin@samsung.com>
Signed-off-by: NChristoffer Dall <christoffer.dall@linaro.org>
      952105ab
    • E
      KVM: arm/arm64: implement kvm_arm_[halt,resume]_guest · 3b92830a
      由 Eric Auger 提交于 
      We introduce kvm_arm_halt_guest and resume functions. They
will be used for IRQ forward state change.

Halt is synchronous and prevents the guest from being re-entered.
We use the same mechanism put in place for PSCI former pause,
now renamed power_off. A new flag is introduced in arch vcpu state,
pause, only meant to be used by those functions.
Signed-off-by: NEric Auger <eric.auger@linaro.org>
Reviewed-by: NChristoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: NChristoffer Dall <christoffer.dall@linaro.org>
      3b92830a
    • E
      KVM: arm/arm64: check power_off in critical section before VCPU run · 101d3da0
      由 Eric Auger 提交于 
      In case a vcpu off PSCI call is called just after we executed the
vcpu_sleep check, we can enter the guest although power_off
is set. Let's check the power_off state in the critical section,
just before entering the guest.
Signed-off-by: NEric Auger <eric.auger@linaro.org>
Reported-by: NChristoffer Dall <christoffer.dall@linaro.org>
Reviewed-by: NChristoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: NChristoffer Dall <christoffer.dall@linaro.org>
      101d3da0
    • E
      KVM: arm/arm64: check power_off in kvm_arch_vcpu_runnable · 4f5f1dc0
      由 Eric Auger 提交于 
      kvm_arch_vcpu_runnable now also checks whether the power_off
flag is set.
Signed-off-by: NEric Auger <eric.auger@linaro.org>
Reviewed-by: NChristoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: NChristoffer Dall <christoffer.dall@linaro.org>
      4f5f1dc0
    • E
      KVM: arm/arm64: rename pause into power_off · 3781528e
      由 Eric Auger 提交于 
      The kvm_vcpu_arch pause field is renamed into power_off to prepare
for the introduction of a new pause field. Also vcpu_pause is renamed
into vcpu_sleep since we will sleep until both power_off and pause are
false.
Signed-off-by: NEric Auger <eric.auger@linaro.org>
Reviewed-by: NChristoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: NChristoffer Dall <christoffer.dall@linaro.org>
      3781528e
    • W
      arm/arm64: KVM : Enable vhost device selection under KVM config menu · 75755c6d
      由 Wei Huang 提交于 
      vhost drivers provide guest VMs with better I/O performance and lower
CPU utilization. This patch allows users to select vhost devices under
KVM configuration menu on ARM. This makes vhost support on arm/arm64
on a par with other architectures (e.g. x86, ppc).
Signed-off-by: NWei Huang <wei@redhat.com>
Signed-off-by: NChristoffer Dall <christoffer.dall@linaro.org>
      75755c6d
    • C
      arm/arm64: KVM: Support edge-triggered forwarded interrupts · 8fe2f19e
      由 Christoffer Dall 提交于 
      We mark edge-triggered interrupts with the HW bit set as queued to
prevent the VGIC code from injecting LRs with both the Active and
Pending bits set at the same time while also setting the HW bit,
because the hardware does not support this.

However, this means that we must also clear the queued flag when we sync
back a LR where the state on the physical distributor went from active
to inactive because the guest deactivated the interrupt.  At this point
we must also check if the interrupt is pending on the distributor, and
tell the VGIC to queue it again if it is.

Since these actions on the sync path are extremely close to those for
level-triggered interrupts, rename process_level_irq to
process_queued_irq, allowing it to cater for both cases.
Signed-off-by: NChristoffer Dall <christoffer.dall@linaro.org>
      8fe2f19e
    • C
      arm/arm64: KVM: Rework the arch timer to use level-triggered semantics · 4b4b4512
      由 Christoffer Dall 提交于 
      The arch timer currently uses edge-triggered semantics in the sense that
the line is never sampled by the vgic and lowering the line from the
timer to the vgic doesn't have any effect on the pending state of
virtual interrupts in the vgic.  This means that we do not support a
guest with the otherwise valid behavior of (1) disable interrupts (2)
enable the timer (3) disable the timer (4) enable interrupts.  Such a
guest would validly not expect to see any interrupts on real hardware,
but will see interrupts on KVM.

This patch fixes this shortcoming through the following series of
changes.

First, we change the flow of the timer/vgic sync/flush operations.  Now
the timer is always flushed/synced before the vgic, because the vgic
samples the state of the timer output.  This has the implication that we
move the timer operations in to non-preempible sections, but that is
fine after the previous commit getting rid of hrtimer schedules on every
entry/exit.

Second, we change the internal behavior of the timer, letting the timer
keep track of its previous output state, and only lower/raise the line
to the vgic when the state changes.  Note that in theory this could have
been accomplished more simply by signalling the vgic every time the
state *potentially* changed, but we don't want to be hitting the vgic
more often than necessary.

Third, we get rid of the use of the map->active field in the vgic and
instead simply set the interrupt as active on the physical distributor
whenever the input to the GIC is asserted and conversely clear the
physical active state when the input to the GIC is deasserted.

Fourth, and finally, we now initialize the timer PPIs (and all the other
unused PPIs for now), to be level-triggered, and modify the sync code to
sample the line state on HW sync and re-inject a new interrupt if it is
still pending at that time.
Signed-off-by: NChristoffer Dall <christoffer.dall@linaro.org>
      4b4b4512
    • C
      arm/arm64: KVM: Add forwarded physical interrupts documentation · 4cf1bc4c
      由 Christoffer Dall 提交于 
      Forwarded physical interrupts on arm/arm64 is a tricky concept and the
way we deal with them is not apparently easy to understand by reading
various specs.

Therefore, add a proper documentation file explaining the flow and
rationale of the behavior of the vgic.

Some of this text was contributed by Marc Zyngier and edited by me.
Omissions and errors are all mine.
Signed-off-by: NChristoffer Dall <christoffer.dall@linaro.org>
      4cf1bc4c
    • C
      arm/arm64: KVM: Use appropriate define in VGIC reset code · 54723bb3
      由 Christoffer Dall 提交于 
      We currently initialize the SGIs to be enabled in the VGIC code, but we
use the VGIC_NR_PPIS define for this purpose, instead of the the more
natural VGIC_NR_SGIS.  Change this slightly confusing use of the
defines.

Note: This should have no functional change, as both names are defined
to the number 16.
Acked-by: NMarc Zyngier <marc.zyngier@arm.com>
Signed-off-by: NChristoffer Dall <christoffer.dall@linaro.org>
      54723bb3
    • C
      arm/arm64: KVM: Implement GICD_ICFGR as RO for PPIs · 8bf9a701
      由 Christoffer Dall 提交于 
      The GICD_ICFGR allows the bits for the SGIs and PPIs to be read only.
We currently simulate this behavior by writing a hardcoded value to the
register for the SGIs and PPIs on every write of these bits to the
register (ignoring what the guest actually wrote), and by writing the
same value as the reset value to the register.

This is a bit counter-intuitive, as the register is RO for these bits,
and we can just implement it that way, allowing us to control the value
of the bits purely in the reset code.
Reviewed-by: NMarc Zyngier <marc.zyngier@arm.com>
Signed-off-by: NChristoffer Dall <christoffer.dall@linaro.org>
      8bf9a701
    • C
      arm/arm64: KVM: vgic: Factor out level irq processing on guest exit · 9103617d
      由 Christoffer Dall 提交于 
      Currently vgic_process_maintenance() processes dealing with a completed
level-triggered interrupt directly, but we are soon going to reuse this
logic for level-triggered mapped interrupts with the HW bit set, so
move this logic into a separate static function.

Probably the most scary part of this commit is convincing yourself that
the current flow is safe compared to the old one.  In the following I
try to list the changes and why they are harmless:

  Move vgic_irq_clear_queued after kvm_notify_acked_irq:
    Harmless because the only potential effect of clearing the queued
    flag wrt.  kvm_set_irq is that vgic_update_irq_pending does not set
    the pending bit on the emulated CPU interface or in the
    pending_on_cpu bitmask if the function is called with level=1.
    However, the point of kvm_notify_acked_irq is to call kvm_set_irq
    with level=0, and we set the queued flag again in
    __kvm_vgic_sync_hwstate later on if the level is stil high.

  Move vgic_set_lr before kvm_notify_acked_irq:
    Also, harmless because the LR are cpu-local operations and
    kvm_notify_acked only affects the dist

  Move vgic_dist_irq_clear_soft_pend after kvm_notify_acked_irq:
    Also harmless, because now we check the level state in the
    clear_soft_pend function and lower the pending bits if the level is
    low.
Reviewed-by: NEric Auger <eric.auger@linaro.org>
Reviewed-by: NMarc Zyngier <marc.zyngier@arm.com>
Signed-off-by: NChristoffer Dall <christoffer.dall@linaro.org>
      9103617d
    • C
      arm/arm64: KVM: arch_timer: Only schedule soft timer on vcpu_block · d35268da
      由 Christoffer Dall 提交于 
      We currently schedule a soft timer every time we exit the guest if the
timer did not expire while running the guest.  This is really not
necessary, because the only work we do in the timer work function is to
kick the vcpu.

Kicking the vcpu does two things:
(1) If the vpcu thread is on a waitqueue, make it runnable and remove it
from the waitqueue.
(2) If the vcpu is running on a different physical CPU from the one
doing the kick, it sends a reschedule IPI.

The second case cannot happen, because the soft timer is only ever
scheduled when the vcpu is not running.  The first case is only relevant
when the vcpu thread is on a waitqueue, which is only the case when the
vcpu thread has called kvm_vcpu_block().

Therefore, we only need to make sure a timer is scheduled for
kvm_vcpu_block(), which we do by encapsulating all calls to
kvm_vcpu_block() with kvm_timer_{un}schedule calls.

Additionally, we only schedule a soft timer if the timer is enabled and
unmasked, since it is useless otherwise.

Note that theoretically userspace can use the SET_ONE_REG interface to
change registers that should cause the timer to fire, even if the vcpu
is blocked without a scheduled timer, but this case was not supported
before this patch and we leave it for future work for now.
Signed-off-by: NChristoffer Dall <christoffer.dall@linaro.org>
      d35268da
    • C
      KVM: Add kvm_arch_vcpu_{un}blocking callbacks · 3217f7c2
      由 Christoffer Dall 提交于 
      Some times it is useful for architecture implementations of KVM to know
when the VCPU thread is about to block or when it comes back from
blocking (arm/arm64 needs to know this to properly implement timers, for
example).

Therefore provide a generic architecture callback function in line with
what we do elsewhere for KVM generic-arch interactions.
Reviewed-by: NMarc Zyngier <marc.zyngier@arm.com>
Signed-off-by: NChristoffer Dall <christoffer.dall@linaro.org>
      3217f7c2
  9. 21 10月, 2015 2 次提交
    • G
      KVM: PPC: Book3S HV: Handle H_DOORBELL on the guest exit path · 70aa3961
      由 Gautham R. Shenoy 提交于 
      Currently a CPU running a guest can receive a H_DOORBELL in the
following two cases:
1) When the CPU is napping due to CEDE or there not being a guest
vcpu.
2) The CPU is running the guest vcpu.

Case 1), the doorbell message is not cleared since we were waking up
from nap. Hence when the EE bit gets set on transition from guest to
host, the H_DOORBELL interrupt is delivered to the host and the
corresponding handler is invoked.

However in Case 2), the message gets cleared by the action of taking
the H_DOORBELL interrupt. Since the CPU was running a guest, instead
of invoking the doorbell handler, the code invokes the second-level
interrupt handler to switch the context from the guest to the host. At
this point the setting of the EE bit doesn't result in the CPU getting
the doorbell interrupt since it has already been delivered once. So,
the handler for this doorbell is never invoked!

This causes softlockups if the missed DOORBELL was an IPI sent from a
sibling subcore on the same CPU.

This patch fixes it by explitly invoking the doorbell handler on the
exit path if the exit reason is H_DOORBELL similar to the way an
EXTERNAL interrupt is handled. Since this will also handle Case 1), we
can unconditionally clear the doorbell message in
kvmppc_check_wake_reason.
Signed-off-by: NGautham R. Shenoy <ego@linux.vnet.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>
      70aa3961
    • N
      KVM: PPC: Implement extension to report number of memslots · bfec5c2c
      由 Nikunj A Dadhania 提交于 
      QEMU assumes 32 memslots if this extension is not implemented. Although,
current value of KVM_USER_MEM_SLOTS is 32, once KVM_USER_MEM_SLOTS
changes QEMU would take a wrong value.
Signed-off-by: NNikunj A Dadhania <nikunj@linux.vnet.ibm.com>
Reviewed-by: NThomas Huth <thuth@redhat.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>
      bfec5c2c