The api for hardware random number generators is currently limited to
devices that never fail. If the hardware is registered as a source for
random numbers it has to work. This prevents the use of i/o based
random number devices where the i/o might fail.

Add a check for errors after the read from a hardware random number device.

This patch is required to support large random numbers retrieved
from the CEX2C cards on System z.
Signed-off-by: NRalph Wuerthner <rwuerthn@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>

If vertical cpu polarization is active then the hypervisor will
dispatch certain cpus for a longer time than other cpus for maximum
performance. For example if a guest would have three virtual cpus,
each of them with a share of 33 percent, then in case of vertical
cpu polarization all of the processing time would be combined to a
single cpu which would run all the time, while the other two cpus
would get nearly no cpu time.

There are three different types of vertical cpus: high, medium and
low. Low cpus hardly get any real cpu time, while high cpus get a
full real cpu. Medium cpus get something in between.

In order to switch between the two possible modes (default is
horizontal) a 0 for horizontal polarization or a 1 for vertical
polarization must be written to the dispatching sysfs attribute:

/sys/devices/system/cpu/dispatching

The polarization of each single cpu can be figured out by the
polarization sysfs attribute of each cpu:

/sys/devices/system/cpu/cpuX/polarization

horizontal, vertical:high, vertical:medium, vertical:low or unknown.

When switching polarization the polarization attribute may contain
the value unknown until the configuration change is done and the
kernel has figured out the new polarization of each cpu.

Note that running a system with different types of vertical cpus may
result in significant performance regressions. If possible only one
type of vertical cpus should be used. All other cpus should be
offlined.
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>

Add s390 backend so we can give the scheduler some hints about the
cpu topology.
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>

Make stfle visible so other code can call this.
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>

Add permanent and temporary model capacity and the corresponding
capacity value fields for the three capacity identifiers to the
output of /proc/sysinfo.
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>

drivers/s390/sysinfo.c uses the store system information intruction to query
the system about information of the machine, the LPAR and additional
hypervisors. KVM has to implement the host part for this instruction.

To avoid code duplication, this patch splits the common definitions from
sysinfo.c into a separate header file include/asm-s390/sysinfo.h for KVM use.
Signed-off-by: NChristian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: NCarsten Otte <cotte@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>

Now the system reports system information messages (SIM) to the user.
The System Reference Code (SRC) which is reported to the user gives
the abbility to lookup the reason of the SIM online in the
documentation of the storage server.
Signed-off-by: NStefan Haberland <stefan.haberland@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>

sys_sigreturn and sys_rt_sigreturn don't take any arguments. So luckily
this resulted only in unneeded instead of incorrect code.
But still this clearly shows why one should not put extern declarations
in C files (will be fixed with a larger sparse patch).
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>

If user space opens a unit record device node then vmur is leaving the kernel
with lock open_mutex still held to prevent other processes from opening the
device simultaneously. This causes lockdep to complain about a lock held when
returning to user space.
Now the mutex is replaced by a wait queue to serialize device open.
Signed-off-by: NFrank Munzert <munzert@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>

When a tape device is set online, offline and online again, the following
error message is printed on the console: "sysfs: duplicate filename
'non-rewinding' can not be created". The reason is that when setting a
device online, the tape driver creates a sysfs symlink from the tape device
to the tape class device. Unfortunately the symlink is not removed
correctly, when the device is set offline. Instead of passing the
tape device object to sysfs_remove_link, the class device object is used.
This patch fixes this problem and uses the correct tape device object now.
Signed-off-by: NMichael Holzheu <holzheu@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>

allocating dasd_fba_private without GFP_DMA results in IO error
during read device characteristics of a FBA disk
Signed-off-by: NStefan Haberland <stefan.haberland@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>

Problem:
Usually every FCP device has its own indicator field the adapter
uses to signal outstanding work. Once a certain limit of devices
is reached, a common indicator field is used. In certain scenarios
qdio resets this common indicator field, but handles only part of
the FCP-devices sharing the common indicator field. Thus inbound
traffic on the non-processed shared FCP-devices is not recognized
immediately.

Solution:
Make sure common indicator field is reset only, if all FCP-devices
sharing the indicator are processed.
Signed-off-by: NUrsula Braun <braunu@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>

Reintroduces in_interrupt() check in sclp_tty code. Add may_schedule
parameter to vt220 write function, so we can let the write function
know if it may schedule or not. So we disallow scheduling for all
console calls and may allow them for tty calls.
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>

It is now possible to trigger cm_enable processing several times in
parallel without causing a kernel panic.
Signed-off-by: NMichael Ernst <mernst@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>

Currently, we don't do much on no path or no device situations during
normal user I/O, since we rely on reports regarding those events by
the machine. If we trigger a path verification to bring our device
state up-to-date, we (a) may recover from path failures earlier and
(b) better handle situations where the hardware/hypervisor doesn't
give us enough notifications.
Signed-off-by: NCornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>

Make sure we wait for previous evaluations triggered by path state
changes to have settled before we manipulate path states again.
Signed-off-by: NCornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>

Fix the following link error with allnoconfig:

vmem.c:(.text+0x175c): undefined reference to `smp_ptlb_all'
vmem.c:(.text+0x1b24): undefined reference to `smp_ptlb_all'
fork.c:(.text+0x4190): undefined reference to `smp_ptlb_all'
: undefined reference to `smp_ptlb_all'
: undefined reference to `smp_ptlb_all'
mm/built-in.o:: more undefined references to `smp_ptlb_all' follow
make[1]: *** [.tmp_vmlinux1] Error 1
make: *** [sub-make] Error 2
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>

This is just a port of 83bd0102
"x86: protect against sigaltstack wraparound".
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>

I compiled the kernel without deadline, and the dasd code exits the old
scheduler (CFQ), fails to load the new one (deadline), and then things just
hang - with one of these (sorry about the weird chars - I copy & pasted it
from a 3270 console):

dasd(eckd): 0.0.0151: 3390/0A(CU:3990/01) Cyl:3338 Head:15 Sec:224
------------ cut here ------------
Badness at kernel/mutex.c:134
Modules linked in: dasd_eckd_mod dasd_mod
CPU: 0 Not tainted 2.6.25-rc3 #9
Process exe (pid: 538, task: 000000000d172000, ksp: 000000000d21ef88)
Krnl PSW : 0404000180000000 000000000022fb5c (mutex_lock_nested+0x2a4/0x2cc)
           R:0 T:1 IO:0 EX:0 Key:0 M:1 W:0 P:0 AS:0 CC:0 PM:0 EA:3
Krnl GPRS: 0000000000024218 000000000076fc78 0000000000000000 000000000000000f
           000000000022f92e 0000000000449898 000000000f921c00 000003e000162590
           00000000001539c4 000000000d172000 070000007fffffff 000000000d21f400
           000000000f8f2560 00000000002413f8 000000000022fb44 000000000d21f400
Krnl Code: 000000000022fb50: bf2f1000           icm     %r2,15,0(%r1)
           000000000022fb54: a774fef6           brc     7,22f940
           000000000022fb58: a7f40001           brc     15,22fb5a
          >000000000022fb5c: a7f4fef2           brc     15,22f940
           000000000022fb60: c0e5fffa112a       brasl   %r14,171db4
           000000000022fb66: 1222               ltr     %r2,%r2
           000000000022fb68: a784fedb           brc     8,22f91e
           000000000022fb6c: c010002a0086       larl    %r1,76fc78
Call Trace:
(<000000000022f92e> mutex_lock_nested+0x76/0x2cc)
 <00000000001539c4> elevator_exit+0x38/0x80
 <0000000000156ffe> blk_cleanup_queue+0x62/0x7c
 <000003e0001d5414> dasd_change_state+0xe0/0x8ec
 <000003e0001d5cae> dasd_set_target_state+0x8e/0x9c
 <000003e0001d5f74> dasd_generic_set_online+0x160/0x284
 <000003e00011e83a> dasd_eckd_set_online+0x2e/0x40
 <0000000000199bf4> ccw_device_set_online+0x170/0x2c0
 <0000000000199d9e> online_store_recog_and_online+0x5a/0x14c
 <000000000019a08a> online_store+0xbe/0x2ec
 <000000000018456c> dev_attr_store+0x38/0x58
 <000000000010efbc> sysfs_write_file+0x130/0x190
 <00000000000af582> vfs_write+0xb2/0x160
 <00000000000afc7c> sys_write+0x54/0x9c
 <0000000000025e16> sys32_write+0x2e/0x50
 <0000000000024218> sysc_noemu+0x10/0x16
 <0000000077e82bd2> 0x77e82bd2

Set elevator pointer to NULL in order to avoid double elevator_exit
calls when elevator_init call for deadline iosched fails.
Also make sure the dasd device driver depends on IOSCHED_DEADLINE so
the default IO scheduler of the dasd driver is present.
Signed-off-by: NJosef 'Jeff' Sipek <jeffpc@josefsipek.net>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>

* git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6:
  it821x: do not describe noraid parameter with its value
  Pb1200/DBAu1200: fix bad IDE resource size
  Au1200: IDE driver build fix
  Au1200: kill IDE driver function prototypes
  avr32 mustn't select HAVE_IDE

Describe noraid parameter with its name (and not its value).
Signed-off-by: NPaul Bolle <pebolle@tiscali.nl>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

The header files for the Pb1200/DBAu1200 boards have wrong definition for the
IDE interface's decoded range length -- it should be 512 bytes according to
what the IDE driver does.  In addition, the IDE platform device claims 1 byte
too many for its memory resource -- fix the platform code and the IDE driver
in accordance.
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

The driver fails to compile with CONFIG_BLK_DEV_IDE_AU1XXX_MDMA2_DBDMA enabled:

drivers/ide/mips/au1xxx-ide.c: In function `auide_build_dmatable':
drivers/ide/mips/au1xxx-ide.c:256: error: implicit declaration of function
`sg_virt'
drivers/ide/mips/au1xxx-ide.c:275: error: implicit declaration of function
`sg_next'
drivers/ide/mips/au1xxx-ide.c:275: warning: assignment makes pointer from
integer without a cast

Fix this by including <linux/scatterlist.h>. While at it, remove the #include's
without which the driver happily builds.
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Fix these warnings emitted when compiling drivers/ide/mips/au1xxx-ide.c:

include/asm/mach-au1x00/au1xxx_ide.h:137: warning: 'auide_tune_drive' declared 
`static' but never defined
include/asm/mach-au1x00/au1xxx_ide.h:138: warning: 'auide_tune_chipset' declared
 `static' but never defined

by wiping out the whole "function prototyping" section from the header file
<asm-mips/mach-au1x00/au1xxx_ide.h> as it mostly declared functions that are
already dead in the IDE driver; move the only useful prototype into the driver.
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

There's a libata based PATA driver for avr32, but no support for 
drivers/ide/ on avr32.

This patch fixes the following compile error:

<--  snip  -->

...
  CC [M]  drivers/ide/ide-cd.o
In file included from /home/bunk/linux/kernel-2.6/git/linux-2.6/drivers/ide/ide-cd.c:37:
/home/bunk/linux/kernel-2.6/git/linux-2.6/include/linux/ide.h:209:21: error: asm/ide.h: No such file or directory
make[3]: *** [drivers/ide/ide-cd.o] Error 1

<--  snip  -->
Signed-off-by: NAdrian Bunk <bunk@kernel.org>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Acked-by: NSam Ravnborg <sam@ravnborg.org>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
  block: update git url for blktrace
  io context: increment task attachment count in ioc_task_link()

* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6:
  USB: remove broken usb-serial num_endpoints check
  USB: option: Add new vendor ID and device ID for AMOI HSDPA modem
  USB: support more Huawei data card product IDs
  USB: option.c: add more device IDs
  USB: Obscure Maxon BP3-USB Device Support 16d8:6280 for option driver

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
  [TCP]: Add return value indication to tcp_prune_ofo_queue().
  PS3: gelic: fix the oops on the broken IE returned from the hypervisor
  b43legacy: fix DMA mapping leakage
  mac80211: remove message on receiving unexpected unencrypted frames
  Update rt2x00 MAINTAINERS entry
  Add rfkill to MAINTAINERS file
  rfkill: Fix device type check when toggling states
  b43legacy: Fix usage of struct device used for DMAing
  ssb: Fix usage of struct device used for DMAing
  MAINTAINERS: move to generic repository for iwlwifi
  b43legacy: fix initvals loading on bcm4303
  rtl8187: Add missing priv->vif assignments
  netconsole: only set CON_PRINTBUFFER if the user specifies a netconsole
  [CAN]: Update documentation of struct sockaddr_can
  MAINTAINERS: isdn4linux@listserv.isdn4linux.de is subscribers-only
  [TCP]: Fix never pruned tcp out-of-order queue.
  [NET_SCHED] sch_api: fix qdisc_tree_decrease_qlen() loop

Describe debug parameters with their names (and not their values).
Signed-off-by: NPaul Bolle <pebolle@tiscali.nl>
Signed-off-by: NDavid Howells <dhowells@redhat.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The num_interrupt_in, num_bulk_in, and other checks in the usb-serial
code are just wrong, there are too many different devices out there with
different numbers of endpoints.  We need to just be sticking with the
device ids instead of trying to catch this kind of thing.  It broke too
many different devices.

This fixes a large number of usb-serial devices to get them working
properly again.


Cc: Oliver Neukum <oliver@neukum.org>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch add new vendor ID and device ID  for AMOI HSDPA modem. 

From: tang kai <tangk73@hotmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

 - declare the unusal device for Huawei data card devices in
   unusual_devs.h
 - disable the product ID matching for Huawei data card devices in
   usb_match_device function of driver.c
 - declare the product IDs in option.c.
Signed-off-by: Nfangxiaozhi <huananhu@huawei.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Add devices by AMOI and NovatelWireless.
Signed-Off-By: NMatthias Urlichs <matthias@urlichs.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The modem was detected, the ttyUSB{0,1,2} appeared, a call could be
made, and the expected data rate was achieved.  Tested for an hour or
two, total of 100Mb.  I shall do more testing.
Signed-off-by: NJames Cameron <quozl@laptop.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Returns non-zero if tp->out_of_order_queue was seen non-empty.
This allows tcp_try_rmem_schedule() to return early.
Signed-off-by: NVitaliy Gusev <vgusev@openvz.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

http://bugzilla.kernel.org/show_bug.cgi?id=10124

this change:

      commit 08f1c192
      Author: Muli Ben-Yehuda <muli@il.ibm.com>
      Date:   Sun Jul 22 00:23:39 2007 +0300

         x86-64: introduce struct pci_sysdata to facilitate sharing of ->sysdata

         This patch introduces struct pci_sysdata to x86 and x86-64, and
         converts the existing two users (NUMA, Calgary) to use it.

         This lays the groundwork for having other users of sysdata, such as
         the PCI domains work.

         The Calgary bits are tested, the NUMA bits just look ok.

replaces pcibios_scan_root by pci_scan_bus_parented...

but in pcibios_scan_root we have a check about scanned busses.

Cc: <yakui.zhao@intel.com>
Cc: Stian Jordet <stian@jordet.net>
Cc: Len Brown <lenb@kernel.org>
Cc: Greg KH <greg@kroah.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "Yinghai Lu" <yhlu.kernel@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The THERMAL_MAX_TRIPS value is set to 10.  It is too few for the Compaq AP550
machine which has 12 trip points.
Signed-off-by: NKrzysztof Helt <krzysztof.h1@wp.pl>
Cc: Len Brown <lenb@kernel.org>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

List could have become empty after the unlocked check that was made earlier,
so check again inside the lock.

Should fix https://bugzilla.redhat.com/show_bug.cgi?id=427765Signed-off-by: NChuck Ebbert <cebbert@redhat.com>
Cc: <stable@kernel.org>
Cc: Len Brown <lenb@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The SPI core now expects num_chipselect to be set correctly as due to added
checks on the chip being selected before an transfer is allowed.  This patch
adds a num_cs field to the platform data which needs to be set correctly
before adding the SPI platform device.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>