Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

bonito board needs some settings by pmic which use i2c access.
It is dependent on the device to be used.
This patch adds standard settings.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

devices enable/disable are controled by dip-switch on bonito board.
If bonito core board is connected to base board,
you can check the settings from FPGA.
This patch adds basic code and controls SCIFA5 settings
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This adds basic bonito board (R-Mobile A1) support
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

R8A7740 GIC can not get external IRQx interrupt directly
without GIC - INTC demux support.

Current AG5 is using GIC - INTCS demux with
special irq relocation. but GIC - INTCA demux
is still not supported and it needs irq number re-mapping.

OTOH, normal INTC support as before is very enough for R8A7740,
because it is not SMP CPU.
This patch adds INTCA/INTCS support instead of GIC.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This patch adds I2C support to r8a7740 CPU
which has lasting errata on I2C I/O pad reset.
This patch is including work-around.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This adds PFC support for the R8A7740 (R-Mobile A1) CPU
This patch is based on v0.1 manual
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This adds preliminary support for the R8A7740 (R-Mobile A1) CPU

Timer, serial, gic, clock are supported at this point.
This patch is based on v0.1 manual
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

The following commits break cpuidle on SH-Mobile ARM:

46bcfad7 cpuidle: Single/Global registration of idle states
e978aa7d cpuidle: Move dev->last_residency update to driver enter routine; remove dev->last_state

This patch remedies these issues by up-porting the SH-Mobile
code to fit with the above introduced framework changes.

It is worth noting that the new code becomes significantly cleaner,
so these framework changes are very welcome. At the same time this
breakage could probably have been avoided by grepping for "last_state"
and "cpuidle_register_driver".
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This patch moves PORT_xx helper macro to sh_pfc.h,
and it expects CPU_ALL_PORT() macro for each CPU
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This patch move PORT_DATA_xx helper macro to sh_pfc.h.
and pfc-sh7372.c used it
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

it is not necessary to have sh7372_xxxx index on static variable
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This patch adds MMC data pin pull-up option for pfc-sh73a0.c,
and select it on ag5evm board.
The MMC read/write will be error without this patch.

Cc: Takashi YOSHII <takashi.yoshii.zj@renesas.com>
Tested-by: NSimon Horman <horms@verge.net.au>
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

ag5evm implements a backlight control, using an I2C controller, therefore
it needs CONFIG_I2C to fix this make failure

arch/arm/mach-shmobile/built-in.o: In function `lcd_on':
pfc-sh73a0.c:(.text+0x2334): undefined reference to `i2c_get_adapter'
pfc-sh73a0.c:(.text+0x2370): undefined reference to `i2c_transfer'

(ignore pfc-sh73a0.c) and to build successfully.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Support PINT on sh73a0 and AG5EVM using INTC PINT macros.

With this patch applied the AG5EVM ethernet is handled
through one of the chained sh73a0 PINT interrupt controllers.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Add a INTC_PINT() macro with various helper bits to allow SoCs
like sh73a0 to suppor the PINT hardware using regular INTC tables.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Implement GPIO hotplugging via TMIO_MMC_HAS_COLD_CD for
AG5EVM SDHI0. This is possible now when INTCA is used for
IRQ triggering on sh73a0. Without INTCA IRQ support we are
left with the GIC hardware block that does not support
dealing with active low interrupt sources.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Improve IRQ triggering support by making use of the macro
INTC_IRQ_PINS_32() for INTCA on sh73a0. Unfortunately it
is not as easy as just using the macro as-is, we need to
do mask and unmaks in the GIC but configure other bits
and ack in INTCA. Update GPIO IRQ mappings while at it.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Make use of INTC_IRQ_PINS_32() for INTCA on sh7372.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Make use of INTC_IRQ_PINS_32() for INTCA on sh7377.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Make use of INTC_IRQ_PINS_16() for INTCA on sh7367.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This patch adds support for sh73a0 GPIO IRQs by making use
of the PFC GPIO IRQ feature. Only IRQ pins are  supported
at this time. In the future when PINT interrupts also are
supported properly we can easily extend the table with such
information. Also, the sh73a0 is currently making use of
the GIC for external interrupt which is rather unflexible
when it comes to triggering configuration at this point.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Always use CS0 shadow area for NOR flash instead of regular CS0
memory area on ap4evb.

When booting from CS0 NOR Flash the regular CS0 memory area is
available, but when booting via USB the MASK ROM gets mapped to
0x0 which gets in the way for the NOR Flash. Always using CS0
shadow area works well for both NOR Flash boot and USB boot.
Signed-off-by: NBastian Hecht <hechtb@gmail.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Always use CS0 shadow area for NOR flash instead of regular CS0
memory area on Mackerel.

When booting from CS0 NOR Flash the regular CS0 memory area is
available, but when booting via USB the MASK ROM gets mapped to
0x0 which gets in the way for the NOR Flash. Always using CS0
shadow area works well for both NOR Flash boot and USB boot.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Add INTC_IRQ_PINS_16() and INTC_IRQ_PINS_32() to mach/intc.h.
These macros define 16 or 32 external IRQ pins on a certain
memory base address. Can be used with INTCA or INTCS.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

The sh_mobile_ceu_camera driver has been converted to use the V4L2
subdevice .[gs]_mbus_config() operations, therefore we don't need
SOCAM_* flags for the soc_camera_platform driver anymore. Remove
them.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Prepare the board to switch to the new subdevice media-bus configuration
operations.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The sh_mobile_csi2 driver will change meaning of the .lanes platform
data field from "bitmask of used lanes" to "number of used lanes."
To avoid a regression during this transition switch ap4evb to rely
on the 2 lane default.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

These files all make use of one of the EXPORT_SYMBOL variants
or the THIS_MODULE macro.  So they will need <linux/export.h>
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>

This allows specific (non-multiplexed) IRQ handlers to be used.

Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: Paul Mundt <lethal@linux-sh.org>
Acked-by: NMagnus Damm <magnus.damm@gmail.com>
Signed-off-by: NSimon Horman <horms@verge.net.au>
Signed-off-by: NChris Ball <cjb@laptop.org>

PPI handling is a bit of an odd beast. It uses its own low level
handling code and is hardwired to the local timers (hence lacking
a registration interface).

Instead, switch the low handling to the normal SPI handling code.
PPIs are handled by the handle_percpu_devid_irq flow.

This also allows the removal of some duplicated code.

Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: David Brown <davidb@codeaurora.org>
Cc: Bryan Huntsman <bryanh@codeaurora.org>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Magnus Damm <magnus.damm@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Acked-by: NDavid Brown <davidb@codeaurora.org>
Tested-by: NDavid Brown <davidb@codeaurora.org>
Tested-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>

This change adds support for the sh7372 A4R power domain.

The sh7372 A4R hardware power domain contains the
SH CPU Core and a set of I/O devices including
multimedia accelerators and I2C controllers.

One special case about A4R is the INTCS interrupt
controller that needs to be saved and restored to
keep working as expected. Also the LCDC hardware
blocks are in a different hardware power domain
but have their IRQs routed only through INTCS. So
as long as LCDCs are active we cannot power down
INTCS because that would risk losing interrupts.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>

This change adds support for the sh7372 A3SP power domain.

The sh7372 A3SP hardware power domain contains a
wide range of I/O devices. The list of I/O devices
include SCIF serial ports, DMA Engine hardware,
SD and MMC controller hardware, USB controllers
and I2C master controllers.

This patch adds the A3SP low level code which
powers the hardware power domain on and off. It
also ties in platform devices to the pm domain
support code.

It is worth noting that the serial console is
hooked up to SCIFA0 on most sh7372 boards, and
the SCIFA0 port is included in the A3SP hardware
power domain. For this reason we cannot output
debug messages from the low level power control
code in the case of A3SP.

QoS support is needed in drivers before we can
enable the A3SP power control on the fly.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>

Rather than clipping the number of CPUs using the compile-time NR_CPUS
constant, use the runtime nr_cpu_ids value instead.  This allows the
nr_cpus command line option to work as expected.

Cc: <stable@kernel.org>
Reported-by: NMark Salter <msalter@redhat.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This patch uses the new cpu_logical_map() macro for converting logical
CPU numbers into physical numbers when dealing with the SCU in the SMP
boot path for sh73a0.

Cc: Magnus Damm <magnus.damm@gmail.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: NWill Deacon <will.deacon@arm.com>