Skip to content

cloud-kernel
cloud-kernel

openanolis / cloud-kernel
接近 2 年 前同步成功

通知 170
Star 36
Fork 7
cloud-kernel
cloud-kernel
切换分支/标签
  1. 30 12月, 2017 4 次提交
    • T
      genirq/msi, x86/vector: Prevent reservation mode for non maskable MSI · bc976233
      由 Thomas Gleixner 提交于 
      The new reservation mode for interrupts assigns a dummy vector when the
interrupt is allocated and assigns a real vector when the interrupt is
requested. The reservation mode prevents vector pressure when devices with
a large amount of queues/interrupts are initialized, but only a minimal
subset of those queues/interrupts is actually used.

This mode has an issue with MSI interrupts which cannot be masked. If the
driver is not careful or the hardware emits an interrupt before the device
irq is requestd by the driver then the interrupt ends up on the dummy
vector as a spurious interrupt which can cause malfunction of the device or
in the worst case a lockup of the machine.

Change the logic for the reservation mode so that the early activation of
MSI interrupts checks whether:

 - the device is a PCI/MSI device
 - the reservation mode of the underlying irqdomain is activated
 - PCI/MSI masking is globally enabled
 - the PCI/MSI device uses either MSI-X, which supports masking, or
   MSI with the maskbit supported.

If one of those conditions is false, then clear the reservation mode flag
in the irq data of the interrupt and invoke irq_domain_activate_irq() with
the reserve argument cleared. In the x86 vector code, clear the can_reserve
flag in the vector allocation data so a subsequent free_irq() won't create
the same situation again. The interrupt stays assigned to a real vector
until pci_disable_msi() is invoked and all allocations are undone.

Fixes: 4900be83 ("x86/vector/msi: Switch to global reservation mode")
Reported-by: NAlexandru Chirvasitu <achirvasub@gmail.com>
Reported-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Tested-by: NAlexandru Chirvasitu <achirvasub@gmail.com>
Tested-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Dou Liyang <douly.fnst@cn.fujitsu.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Mikael Pettersson <mikpelinux@gmail.com>
Cc: Josh Poulson <jopoulso@microsoft.com>
Cc: Mihai Costache <v-micos@microsoft.com>
Cc: Stephen Hemminger <sthemmin@microsoft.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: linux-pci@vger.kernel.org
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Cc: Dexuan Cui <decui@microsoft.com>
Cc: Simon Xiao <sixiao@microsoft.com>
Cc: Saeed Mahameed <saeedm@mellanox.com>
Cc: Jork Loeser <Jork.Loeser@microsoft.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: devel@linuxdriverproject.org
Cc: KY Srinivasan <kys@microsoft.com>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Sakari Ailus <sakari.ailus@intel.com>,
Cc: linux-media@vger.kernel.org
Link: https://lkml.kernel.org/r/alpine.DEB.2.20.1712291406420.1899@nanos
Link: https://lkml.kernel.org/r/alpine.DEB.2.20.1712291409460.1899@nanos
      bc976233
    • T
      genirq/irqdomain: Rename early argument of irq_domain_activate_irq() · 702cb0a0
      由 Thomas Gleixner 提交于 
      The 'early' argument of irq_domain_activate_irq() is actually used to
denote reservation mode. To avoid confusion, rename it before abuse
happens.

No functional change.

Fixes: 72491643 ("genirq/irqdomain: Update irq_domain_ops.activate() signature")
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Cc: Alexandru Chirvasitu <achirvasub@gmail.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Dou Liyang <douly.fnst@cn.fujitsu.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Mikael Pettersson <mikpelinux@gmail.com>
Cc: Josh Poulson <jopoulso@microsoft.com>
Cc: Mihai Costache <v-micos@microsoft.com>
Cc: Stephen Hemminger <sthemmin@microsoft.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: linux-pci@vger.kernel.org
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Cc: Dexuan Cui <decui@microsoft.com>
Cc: Simon Xiao <sixiao@microsoft.com>
Cc: Saeed Mahameed <saeedm@mellanox.com>
Cc: Jork Loeser <Jork.Loeser@microsoft.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: devel@linuxdriverproject.org
Cc: KY Srinivasan <kys@microsoft.com>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Sakari Ailus <sakari.ailus@intel.com>,
Cc: linux-media@vger.kernel.org
      702cb0a0
    • T
      genirq: Introduce IRQD_CAN_RESERVE flag · 69790ba9
      由 Thomas Gleixner 提交于 
      Add a new flag to mark interrupts which can use reservation mode. This is
going to be used in subsequent patches to disable reservation mode for a
certain class of MSI devices.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Tested-by: NAlexandru Chirvasitu <achirvasub@gmail.com>
Tested-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Dou Liyang <douly.fnst@cn.fujitsu.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Mikael Pettersson <mikpelinux@gmail.com>
Cc: Josh Poulson <jopoulso@microsoft.com>
Cc: Mihai Costache <v-micos@microsoft.com>
Cc: Stephen Hemminger <sthemmin@microsoft.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: linux-pci@vger.kernel.org
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Cc: Dexuan Cui <decui@microsoft.com>
Cc: Simon Xiao <sixiao@microsoft.com>
Cc: Saeed Mahameed <saeedm@mellanox.com>
Cc: Jork Loeser <Jork.Loeser@microsoft.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: devel@linuxdriverproject.org
Cc: KY Srinivasan <kys@microsoft.com>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Sakari Ailus <sakari.ailus@intel.com>,
Cc: linux-media@vger.kernel.org
      69790ba9
    • T
      genirq/msi: Handle reactivation only on success · da5dd9e8
      由 Thomas Gleixner 提交于 
      When analyzing the fallout of the x86 vector allocation rework it turned
out that the error handling in msi_domain_alloc_irqs() is broken.

If MSI_FLAG_MUST_REACTIVATE is set for a MSI domain then it clears the
activation flag for a successfully initialized msi descriptor. If a
subsequent initialization fails then the error handling code path does not
deactivate the interrupt because the activation flag got cleared.

Move the clearing of the activation flag outside of the initialization loop
so that an eventual failure can be cleaned up correctly.

Fixes: 22d0b12f ("genirq/irqdomain: Add force reactivation flag to irq domains")
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Tested-by: NAlexandru Chirvasitu <achirvasub@gmail.com>
Tested-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Dou Liyang <douly.fnst@cn.fujitsu.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Mikael Pettersson <mikpelinux@gmail.com>
Cc: Josh Poulson <jopoulso@microsoft.com>
Cc: Mihai Costache <v-micos@microsoft.com>
Cc: Stephen Hemminger <sthemmin@microsoft.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: linux-pci@vger.kernel.org
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Cc: Dexuan Cui <decui@microsoft.com>
Cc: Simon Xiao <sixiao@microsoft.com>
Cc: Saeed Mahameed <saeedm@mellanox.com>
Cc: Jork Loeser <Jork.Loeser@microsoft.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: devel@linuxdriverproject.org
Cc: KY Srinivasan <kys@microsoft.com>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Sakari Ailus <sakari.ailus@intel.com>,
Cc: linux-media@vger.kernel.org
      da5dd9e8
  3. 28 12月, 2017 2 次提交
  5. 05 12月, 2017 1 次提交
  7. 24 11月, 2017 1 次提交
  9. 22 11月, 2017 1 次提交
    • K
      treewide: Switch DEFINE_TIMER callbacks to struct timer_list * · 24ed960a
      由 Kees Cook 提交于 
      This changes all DEFINE_TIMER() callbacks to use a struct timer_list
pointer instead of unsigned long. Since the data argument has already been
removed, none of these callbacks are using their argument currently, so
this renames the argument to "unused".

Done using the following semantic patch:

@match_define_timer@
declarer name DEFINE_TIMER;
identifier _timer, _callback;
@@

 DEFINE_TIMER(_timer, _callback);

@change_callback depends on match_define_timer@
identifier match_define_timer._callback;
type _origtype;
identifier _origarg;
@@

 void
-_callback(_origtype _origarg)
+_callback(struct timer_list *unused)
 { ... }
Signed-off-by: NKees Cook <keescook@chromium.org>
      24ed960a
  11. 13 11月, 2017 3 次提交
  13. 10 11月, 2017 1 次提交
    • M
      genirq: Track whether the trigger type has been set · 4f8413a3
      由 Marc Zyngier 提交于 
      When requesting a shared interrupt, we assume that the firmware
support code (DT or ACPI) has called irqd_set_trigger_type
already, so that we can retrieve it and check that the requester
is being reasonnable.

Unfortunately, we still have non-DT, non-ACPI systems around,
and these guys won't call irqd_set_trigger_type before requesting
the interrupt. The consequence is that we fail the request that
would have worked before.

We can either chase all these use cases (boring), or address it
in core code (easier). Let's have a per-irq_desc flag that
indicates whether irqd_set_trigger_type has been called, and
let's just check it when checking for a shared interrupt.
If it hasn't been set, just take whatever the interrupt
requester asks.

Fixes: 382bd4de ("genirq: Use irqd_get_trigger_type to compare the trigger type for shared IRQs")
Cc: stable@vger.kernel.org
Reported-and-tested-by: NPetr Cvek <petrcvekcz@gmail.com>
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>
      4f8413a3
  15. 08 11月, 2017 1 次提交
  17. 02 11月, 2017 1 次提交
    • G
      License cleanup: add SPDX GPL-2.0 license identifier to files with no license · b2441318
      由 Greg Kroah-Hartman 提交于 
      Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.

By default all files without license information are under the default
license of the kernel, which is GPL version 2.

Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier.  The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.

This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.

How this work was done:

Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
 - file had no licensing information it it.
 - file was a */uapi/* one with no licensing information in it,
 - file was a */uapi/* one with existing licensing information,

Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.

The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne.  Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.

The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed.  Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.

Criteria used to select files for SPDX license identifier tagging was:
 - Files considered eligible had to be source code files.
 - Make and config files were included as candidates if they contained >5
   lines of source
 - File already had some variant of a license header in it (even if <5
   lines).

All documentation files were explicitly excluded.

The following heuristics were used to determine which SPDX license
identifiers to apply.

 - when both scanners couldn't find any license traces, file was
   considered to have no license information in it, and the top level
   COPYING file license applied.

   For non */uapi/* files that summary was:

   SPDX license identifier                            # files
   ---------------------------------------------------|-------
   GPL-2.0                                              11139

   and resulted in the first patch in this series.

   If that file was a */uapi/* path one, it was "GPL-2.0 WITH
   Linux-syscall-note" otherwise it was "GPL-2.0".  Results of that was:

   SPDX license identifier                            # files
   ---------------------------------------------------|-------
   GPL-2.0 WITH Linux-syscall-note                        930

   and resulted in the second patch in this series.

 - if a file had some form of licensing information in it, and was one
   of the */uapi/* ones, it was denoted with the Linux-syscall-note if
   any GPL family license was found in the file or had no licensing in
   it (per prior point).  Results summary:

   SPDX license identifier                            # files
   ---------------------------------------------------|------
   GPL-2.0 WITH Linux-syscall-note                       270
   GPL-2.0+ WITH Linux-syscall-note                      169
   ((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause)    21
   ((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause)    17
   LGPL-2.1+ WITH Linux-syscall-note                      15
   GPL-1.0+ WITH Linux-syscall-note                       14
   ((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause)    5
   LGPL-2.0+ WITH Linux-syscall-note                       4
   LGPL-2.1 WITH Linux-syscall-note                        3
   ((GPL-2.0 WITH Linux-syscall-note) OR MIT)              3
   ((GPL-2.0 WITH Linux-syscall-note) AND MIT)             1

   and that resulted in the third patch in this series.

 - when the two scanners agreed on the detected license(s), that became
   the concluded license(s).

 - when there was disagreement between the two scanners (one detected a
   license but the other didn't, or they both detected different
   licenses) a manual inspection of the file occurred.

 - In most cases a manual inspection of the information in the file
   resulted in a clear resolution of the license that should apply (and
   which scanner probably needed to revisit its heuristics).

 - When it was not immediately clear, the license identifier was
   confirmed with lawyers working with the Linux Foundation.

 - If there was any question as to the appropriate license identifier,
   the file was flagged for further research and to be revisited later
   in time.

In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.

Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights.  The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.

Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.

In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.

Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
 - a full scancode scan run, collecting the matched texts, detected
   license ids and scores
 - reviewing anything where there was a license detected (about 500+
   files) to ensure that the applied SPDX license was correct
 - reviewing anything where there was no detection but the patch license
   was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
   SPDX license was correct

This produced a worksheet with 20 files needing minor correction.  This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.

These .csv files were then reviewed by Greg.  Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected.  This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.)  Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: NKate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: NPhilippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
      b2441318
  19. 01 11月, 2017 1 次提交
  21. 29 10月, 2017 1 次提交
    • C
      genirq: Document vcpu_info usage for percpu_devid interrupts · 250a53d6
      由 Christoffer Dall 提交于 
      It is currently unclear how to set the VCPU affinity for a percpu_devid
interrupt , since the Linux irq_data structure describes the state for
multiple interrupts, one for each physical CPU on the system.  Since
each such interrupt can be associated with different VCPUs or none at
all, associating a single VCPU state with such an interrupt does not
capture the necessary semantics.

The implementers of irq_set_affinity are the Intel and AMD IOMMUs, and
the ARM GIC irqchip.  The Intel and AMD callers do not appear to use
percpu_devid interrupts, and the ARM GIC implementation only checks the
pointer against NULL vs. non-NULL.

Therefore, simply update the function documentation to explain the
expected use in the context of percpu_devid interrupts, allowing future
changes or additions to irqchip implementers to do the right thing.
Signed-off-by: NChristoffer Dall <cdall@linaro.org>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Acked-by: NMarc Zyngier <marc.zyngier@arm.com>
Cc: kvm@vger.kernel.org
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Eric Auger <eric.auger@redhat.com>
Cc: kvmarm@lists.cs.columbia.edu
Cc: linux-arm-kernel@lists.infradead.org
Link: https://lkml.kernel.org/r/1509093281-15225-13-git-send-email-cdall@linaro.org
      250a53d6
  23. 19 10月, 2017 2 次提交
  25. 18 10月, 2017 2 次提交
  27. 13 10月, 2017 2 次提交
    • D
      genirq: generic chip: remove irq_gc_mask_disable_reg_and_ack() · 0d08af35
      由 Doug Berger 提交于 
      Any usage of the irq_gc_mask_disable_reg_and_ack() function has
been replaced with the desired functionality.

The incorrect and ambiguously named function is removed here to
prevent accidental misuse.
Signed-off-by: NDoug Berger <opendmb@gmail.com>
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>
      0d08af35
    • D
      genirq: generic chip: Add irq_gc_mask_disable_and_ack_set() · 20608924
      由 Doug Berger 提交于 
      The irq_gc_mask_disable_reg_and_ack() function name implies that it
provides the combined functions of irq_gc_mask_disable_reg() and
irq_gc_ack().  However, the implementation does not actually do
that since it writes the mask instead of the disable register. It
also does not maintain the mask cache which makes it inappropriate
to use with other masking functions.

In addition, commit 659fb32d ("genirq: replace irq_gc_ack() with
{set,clr}_bit variants (fwd)") effectively renamed irq_gc_ack() to
irq_gc_ack_set_bit() so this function probably should have also been
renamed at that time.

The generic chip code currently provides three functions for use
with the irq_mask member of the irq_chip structure and two functions
for use with the irq_ack member of the irq_chip structure. These
functions could be combined into six functions for use with the
irq_mask_ack member of the irq_chip structure.  However, since only
one of the combinations is currently used, only the function
irq_gc_mask_disable_and_ack_set() is added by this commit.

The '_reg' and '_bit' portions of the base function name were left
out of the new combined function name in an attempt to keep the
function name length manageable with the 80 character source code
line length while still allowing the distinct aspects of each
combination to be captured by the name.

If other combinations are desired in the future please add them to
the irq generic chip library at that time.
Signed-off-by: NDoug Berger <opendmb@gmail.com>
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>
      20608924
  29. 09 10月, 2017 3 次提交
    • T
      genirq/cpuhotplug: Enforce affinity setting on startup of managed irqs · e43b3b58
      由 Thomas Gleixner 提交于 
      Managed interrupts can end up in a stale state on CPU hotplug. If the
interrupt is not targeting a single CPU, i.e. the affinity mask spawns
multiple CPUs then the following can happen:

After boot:

dstate:   0x01601200
            IRQD_ACTIVATED
            IRQD_IRQ_STARTED
            IRQD_SINGLE_TARGET
            IRQD_AFFINITY_SET
            IRQD_AFFINITY_MANAGED
node:     0
affinity: 24-31
effectiv: 24
pending:  0

After offlining CPU 31 - 24

dstate:   0x01a31000
            IRQD_IRQ_DISABLED
            IRQD_IRQ_MASKED
            IRQD_SINGLE_TARGET
            IRQD_AFFINITY_SET
            IRQD_AFFINITY_MANAGED
            IRQD_MANAGED_SHUTDOWN
node:     0
affinity: 24-31
effectiv: 24
pending:  0

Now CPU 25 gets onlined again, so it should get the effective interrupt
affinity for this interruopt, but due to the x86 interrupt affinity setter
restrictions this ends up after restarting the interrupt with:

dstate:   0x01601300
            IRQD_ACTIVATED
            IRQD_IRQ_STARTED
            IRQD_SINGLE_TARGET
            IRQD_AFFINITY_SET
            IRQD_SETAFFINITY_PENDING
            IRQD_AFFINITY_MANAGED
node:     0
affinity: 24-31
effectiv: 24
pending:  24-31

So the interrupt is still affine to CPU 24, which was the last CPU to go
offline of that affinity set and the move to an online CPU within 24-31,
in this case 25, is pending. This mechanism is x86/ia64 specific as those
architectures cannot move interrupts from thread context and do this when
an interrupt is actually handled. So the move is set to pending.

Whats worse is that offlining CPU 25 again results in:

dstate:   0x01601300
            IRQD_ACTIVATED
            IRQD_IRQ_STARTED
            IRQD_SINGLE_TARGET
            IRQD_AFFINITY_SET
            IRQD_SETAFFINITY_PENDING
            IRQD_AFFINITY_MANAGED
node:     0
affinity: 24-31
effectiv: 24
pending:  24-31

This means the interrupt has not been shut down, because the outgoing CPU
is not in the effective affinity mask, but of course nothing notices that
the effective affinity mask is pointing at an offline CPU.

In the case of restarting a managed interrupt the move restriction does not
apply, so the affinity setting can be made unconditional. This needs to be
done _before_ the interrupt is started up as otherwise the condition for
moving it from thread context would not longer be fulfilled.

With that change applied onlining CPU 25 after offlining 31-24 results in:

dstate:   0x01600200
            IRQD_ACTIVATED
            IRQD_IRQ_STARTED
            IRQD_SINGLE_TARGET
            IRQD_AFFINITY_MANAGED
node:     0
affinity: 24-31
effectiv: 25
pending:  

And after offlining CPU 25:

dstate:   0x01a30000
            IRQD_IRQ_DISABLED
            IRQD_IRQ_MASKED
            IRQD_SINGLE_TARGET
            IRQD_AFFINITY_MANAGED
            IRQD_MANAGED_SHUTDOWN
node:     0
affinity: 24-31
effectiv: 25
pending:  

which is the correct and expected result.

Fixes: 761ea388 ("genirq: Handle managed irqs gracefully in irq_startup()")
Reported-by: NYASUAKI ISHIMATSU <yasu.isimatu@gmail.com>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Cc: axboe@kernel.dk
Cc: linux-scsi@vger.kernel.org
Cc: Sumit Saxena <sumit.saxena@broadcom.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: mpe@ellerman.id.au
Cc: Shivasharan Srikanteshwara <shivasharan.srikanteshwara@broadcom.com>
Cc: Kashyap Desai <kashyap.desai@broadcom.com>
Cc: keith.busch@intel.com
Cc: peterz@infradead.org
Cc: Hannes Reinecke <hare@suse.de>
Cc: Christoph Hellwig <hch@lst.de>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/alpine.DEB.2.20.1710042208400.2406@nanos
      e43b3b58
    • T
      genirq/cpuhotplug: Add sanity check for effective affinity mask · 60b09c51
      由 Thomas Gleixner 提交于 
      The effective affinity mask handling has no safety net when the mask is not
updated by the interrupt chip or the mask contains offline CPUs.

If that happens the CPU unplug code fails to migrate interrupts.

Add sanity checks and emit a warning when the mask contains only offline
CPUs.

Fixes: 415fcf1a ("genirq/cpuhotplug: Use effective affinity mask")
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/alpine.DEB.2.20.1710042208400.2406@nanos
      60b09c51
    • T
      genirq: Warn when effective affinity is not updated · 19e1d4e9
      由 Thomas Gleixner 提交于 
      Emit a one time warning when the effective affinity mask is enabled in
Kconfig, but the interrupt chip does not update the mask in its
irq_set_affinity() callback,
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Link: http://lkml.kernel.org/r/alpine.DEB.2.20.1710042208400.2406@nanos
      19e1d4e9
  31. 05 10月, 2017 1 次提交
    • K
      timer: Remove expires and data arguments from DEFINE_TIMER · 1d27e3e2
      由 Kees Cook 提交于 
      Drop the arguments from the macro and adjust all callers with the
following script:

  perl -pi -e 's/DEFINE_TIMER\((.*), 0, 0\);/DEFINE_TIMER($1);/g;' \
    $(git grep DEFINE_TIMER | cut -d: -f1 | sort -u | grep -v timer.h)
Signed-off-by: NKees Cook <keescook@chromium.org>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org> # for m68k parts
Acked-by: Guenter Roeck <linux@roeck-us.net> # for watchdog parts
Acked-by: David S. Miller <davem@davemloft.net> # for networking parts
Acked-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Kalle Valo <kvalo@codeaurora.org> # for wireless parts
Acked-by: NArnd Bergmann <arnd@arndb.de>
Cc: linux-mips@linux-mips.org
Cc: Petr Mladek <pmladek@suse.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Lai Jiangshan <jiangshanlai@gmail.com>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: linux1394-devel@lists.sourceforge.net
Cc: Chris Metcalf <cmetcalf@mellanox.com>
Cc: linux-s390@vger.kernel.org
Cc: linux-wireless@vger.kernel.org
Cc: "James E.J. Bottomley" <jejb@linux.vnet.ibm.com>
Cc: Wim Van Sebroeck <wim@iguana.be>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Ursula Braun <ubraun@linux.vnet.ibm.com>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Harish Patil <harish.patil@cavium.com>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Michael Reed <mdr@sgi.com>
Cc: Manish Chopra <manish.chopra@cavium.com>
Cc: Len Brown <len.brown@intel.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: linux-pm@vger.kernel.org
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Mark Gross <mark.gross@intel.com>
Cc: linux-watchdog@vger.kernel.org
Cc: linux-scsi@vger.kernel.org
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Stefan Richter <stefanr@s5r6.in-berlin.de>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: netdev@vger.kernel.org
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: linuxppc-dev@lists.ozlabs.org
Cc: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Link: https://lkml.kernel.org/r/1507159627-127660-11-git-send-email-keescook@chromium.orgSigned-off-by: NThomas Gleixner <tglx@linutronix.de>
      1d27e3e2
  33. 28 9月, 2017 1 次提交
  35. 26 9月, 2017 12 次提交
    • M
      irqdomain: Add __rcu annotations to radix tree accessors · 7755d83e
      由 Masahiro Yamada 提交于 
      Fix various address spaces warning of sparse.

kernel/irq/irqdomain.c:1463:14: warning: incorrect type in assignment (different address spaces)
kernel/irq/irqdomain.c:1463:14:    expected void **slot
kernel/irq/irqdomain.c:1463:14:    got void [noderef] <asn:4>**
kernel/irq/irqdomain.c:1465:66: warning: incorrect type in argument 2 (different address spaces)
kernel/irq/irqdomain.c:1465:66:    expected void [noderef] <asn:4>**slot
kernel/irq/irqdomain.c:1465:66:    got void **slot
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Link: https://lkml.kernel.org/r/1506082841-11530-1-git-send-email-yamada.masahiro@socionext.com
      7755d83e
    • T
      genirq/matrix: Add tracepoints · ec0f7cd2
      由 Thomas Gleixner 提交于 
      Add tracepoints for the irq bitmap matrix allocator.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Tested-by: NJuergen Gross <jgross@suse.com>
Tested-by: NYu Chen <yu.c.chen@intel.com>
Acked-by: NJuergen Gross <jgross@suse.com>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Alok Kataria <akataria@vmware.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Rui Zhang <rui.zhang@intel.com>
Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Len Brown <lenb@kernel.org>
Link: https://lkml.kernel.org/r/20170913213153.279468022@linutronix.de
      ec0f7cd2
    • T
      genirq: Implement bitmap matrix allocator · 2f75d9e1
      由 Thomas Gleixner 提交于 
      Implement the infrastructure for a simple bitmap based allocator, which
will replace the x86 vector allocator. It's in the core code as other
architectures might be able to reuse/extend it. For now it only implements
allocations for single CPUs, but it's simple to add multi CPU allocation
support if required.

The concept is rather simple:

 Global information:
 	system_vector bitmap
	global accounting

 PerCPU information:
 	allocation bitmap
	managed allocation bitmap
	local accounting

The system vector bitmap is used to exclude vectors system wide from the
allocation space.

The allocation bitmap is used to keep track of per cpu used vectors.

The managed allocation bitmap is used to reserve vectors for managed
interrupts.

When a regular (non managed) interrupt allocation happens then the
following rule applies:

      tmpmap = system_map | alloc_map | managed_map
      find_zero_bit(tmpmap)

Oring the bitmaps together gives the real available space. The same rule
applies for reserving a managed interrupt vector. But contrary to the
regular interrupts the reservation only marks the bit in the managed map
and therefor excludes it from the regular allocations. The managed map is
only cleaned out when the a managed interrupt is completely released and it
stays alive accross CPU offline/online operations.

For managed interrupt allocations the rule is:

      tmpmap = managed_map & ~alloc_map
      find_first_bit(tmpmap)

This returns the first bit which is in the managed map, but not yet
allocated in the allocation map. The allocation marks it in the allocation
map and hands it back to the caller for use.

The rest of the code are helper functions to handle the various
requirements and the accounting which are necessary to replace the x86
vector allocation code. The result is a single patch as the evolution of
this infrastructure cannot be represented in bits and pieces.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Tested-by: NJuergen Gross <jgross@suse.com>
Tested-by: NYu Chen <yu.c.chen@intel.com>
Acked-by: NJuergen Gross <jgross@suse.com>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Alok Kataria <akataria@vmware.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Rui Zhang <rui.zhang@intel.com>
Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Chris Metcalf <cmetcalf@mellanox.com>
Cc: Len Brown <lenb@kernel.org>
Link: https://lkml.kernel.org/r/20170913213153.185437174@linutronix.de
      2f75d9e1
    • T
      genirq/irqdomain: Add force reactivation flag to irq domains · 22d0b12f
      由 Thomas Gleixner 提交于 
      Allow irqdomains to tell the core code, that after early activation the
interrupt needs to be reactivated at request_irq() time.

This allows reservation of vectors at early activation time and actual
vector assignment at request_irq() time.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Tested-by: NJuergen Gross <jgross@suse.com>
Tested-by: NYu Chen <yu.c.chen@intel.com>
Acked-by: NJuergen Gross <jgross@suse.com>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Alok Kataria <akataria@vmware.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Rui Zhang <rui.zhang@intel.com>
Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Len Brown <lenb@kernel.org>
Link: https://lkml.kernel.org/r/20170913213153.106242536@linutronix.de
      22d0b12f
    • T
      genirq/irqdomain: Propagate early activation · 42e1cc2d
      由 Thomas Gleixner 提交于 
      Propagate the early activation mode to the irqdomain activate()
callbacks. This is required for the upcoming reservation, late vector
assignment scheme, so that the early activation call can act accordingly.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Tested-by: NJuergen Gross <jgross@suse.com>
Tested-by: NYu Chen <yu.c.chen@intel.com>
Acked-by: NJuergen Gross <jgross@suse.com>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Alok Kataria <akataria@vmware.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Rui Zhang <rui.zhang@intel.com>
Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Len Brown <lenb@kernel.org>
Link: https://lkml.kernel.org/r/20170913213153.028353660@linutronix.de
      42e1cc2d
    • T
      genirq/irqdomain: Allow irq_domain_activate_irq() to fail · bb9b428a
      由 Thomas Gleixner 提交于 
      Allow irq_domain_activate_irq() to fail. This is required to support a
reservation and late vector assignment scheme.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Tested-by: NJuergen Gross <jgross@suse.com>
Tested-by: NYu Chen <yu.c.chen@intel.com>
Acked-by: NJuergen Gross <jgross@suse.com>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Alok Kataria <akataria@vmware.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Rui Zhang <rui.zhang@intel.com>
Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Len Brown <lenb@kernel.org>
Link: https://lkml.kernel.org/r/20170913213152.933882227@linutronix.de
      bb9b428a
    • T
      genirq/irqdomain: Update irq_domain_ops.activate() signature · 72491643
      由 Thomas Gleixner 提交于 
      The irq_domain_ops.activate() callback has no return value and no way to
tell the function that the activation is early.

The upcoming changes to support a reservation scheme which allows to assign
interrupt vectors on x86 only when the interrupt is actually requested
requires:

  - A return value, so activation can fail at request_irq() time
  
  - Information that the activate invocation is early, i.e. before
    request_irq().
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Tested-by: NJuergen Gross <jgross@suse.com>
Tested-by: NYu Chen <yu.c.chen@intel.com>
Acked-by: NJuergen Gross <jgross@suse.com>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Alok Kataria <akataria@vmware.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Rui Zhang <rui.zhang@intel.com>
Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Len Brown <lenb@kernel.org>
Link: https://lkml.kernel.org/r/20170913213152.848490816@linutronix.de
      72491643
    • T
      genirq: Separate activation and startup · c942cee4
      由 Thomas Gleixner 提交于 
      Activation of an interrupt and startup are currently a combo
functionlity. That works so far, but upcoming changes require a strict
separation because the activation can fail in future.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Tested-by: NJuergen Gross <jgross@suse.com>
Tested-by: NYu Chen <yu.c.chen@intel.com>
Acked-by: NJuergen Gross <jgross@suse.com>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Alok Kataria <akataria@vmware.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Rui Zhang <rui.zhang@intel.com>
Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Len Brown <lenb@kernel.org>
Link: https://lkml.kernel.org/r/20170913213152.754334077@linutronix.de
      c942cee4
    • T
      genirq: Set managed shut down flag at init · 239306fe
      由 Thomas Gleixner 提交于 
      Managed interrupts should start up in managed shutdown mode. Set the status
flag when initialising the irq descriptor.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Tested-by: NJuergen Gross <jgross@suse.com>
Tested-by: NYu Chen <yu.c.chen@intel.com>
Acked-by: NJuergen Gross <jgross@suse.com>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Alok Kataria <akataria@vmware.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Rui Zhang <rui.zhang@intel.com>
Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Len Brown <lenb@kernel.org>
Link: https://lkml.kernel.org/r/20170913213152.669687742@linutronix.de
      239306fe
    • T
      genirq: Make state consistent for !IRQ_DOMAIN_HIERARCHY · 457f6d35
      由 Thomas Gleixner 提交于 
      In the !IRQ_DOMAIN_HIERARCHY cas the activation stubs are not
setting/clearing the activation status bits. This is not a problem at the
moment, but upcoming changes require a correct status.

Add the set/clear incovations to the stub functions and move them to the
core internal header to avoid duplication and visibility outside the core.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Tested-by: NJuergen Gross <jgross@suse.com>
Tested-by: NYu Chen <yu.c.chen@intel.com>
Acked-by: NJuergen Gross <jgross@suse.com>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Alok Kataria <akataria@vmware.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Rui Zhang <rui.zhang@intel.com>
Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Len Brown <lenb@kernel.org>
Link: https://lkml.kernel.org/r/20170913213152.591985591@linutronix.de
      457f6d35
    • T
      irqdomain/debugfs: Provide domain specific debug callback · c3e7239a
      由 Thomas Gleixner 提交于 
      Some interrupt domains like the X86 vector domain has special requirements
for debugging, like showing the vector usage on the CPUs.

Add a callback to the irqdomain ops which can be filled in by domains which
require it and add conditional invocations to the irqdomain and the per irq
debug files.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Tested-by: NJuergen Gross <jgross@suse.com>
Tested-by: NYu Chen <yu.c.chen@intel.com>
Acked-by: NJuergen Gross <jgross@suse.com>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Alok Kataria <akataria@vmware.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Rui Zhang <rui.zhang@intel.com>
Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Len Brown <lenb@kernel.org>
Link: https://lkml.kernel.org/r/20170913213152.512937505@linutronix.de
      c3e7239a
    • T
      genirq/msi: Capture device name for debugfs · 07557ccb
      由 Thomas Gleixner 提交于 
      For debugging the allocation of unused or potentially leaked interrupt
descriptor it's helpful to have some information about the site which
allocated them. In case of MSI this is simple because the caller hands the
device struct pointer into the domain allocation function.

Duplicate the device name and show it in the debugfs entry of the interrupt
descriptor.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Tested-by: NJuergen Gross <jgross@suse.com>
Tested-by: NYu Chen <yu.c.chen@intel.com>
Acked-by: NJuergen Gross <jgross@suse.com>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Alok Kataria <akataria@vmware.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Rui Zhang <rui.zhang@intel.com>
Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Len Brown <lenb@kernel.org>
Link: https://lkml.kernel.org/r/20170913213152.433038426@linutronix.de
      07557ccb