Pass board specific data for MUSB (like interface_type,
mode etc) from board file by defining board
specific structure.

Each board file can define this structure based on
its requirement and pass this information to the
driver.
Signed-off-by: NMaulik Mankad <x0082077@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Gupta Ajay Kumar <ajay.gupta@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

omap3430 TRM says the OTG address space is 4k, not 8k.

Cc: linux-usb@vger.kernel.org
Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patch removes #ifdef around usb_nop_xceiv_register()
from board-omap3evm.c
Signed-off-by: NMaulik Mankad <x0082077@ti.com>
Acked-by: NOlof Johansson <olof@lixom.net>
Acked-by: NFelipe Balbi <felipe.balbi@nokia.com>
Acked-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NTony Lindgren <tony@atomide.com>

These patches add board support for the Timll DevKit8000.

The DevKit8000 is a beagle board clone from Timll, sold by
armkits.com. The DevKit8000 has RS232 serial port, LCD, DVI-D,
S-Video, Ethernet, SD/MMC, keyboard, camera, SPI, I2C, USB and
JTAG interface.
Signed-off-by: NThomas Weber <weber@corscience.de>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add platform hook-up interface to support I2C based GPIo expander
(TCA6416).

There are 3 instances of I2C Expander on AM3517EVM,
	- One is over I2C-2 mounted on Base board
	- Two are over I2C3 mounted on UI Card
Signed-off-by: NVaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add platform hook-up interface to support RTC driver (S35390A).
Signed-off-by: NVaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add basic I2C board Hook-up support, where all the 3 I2C instances
are getting registered.
Signed-off-by: NVaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

If not configured it will be exported as normal GPIO led.
Signed-off-by: NJonas Zetterberg <jozz@jozz.se>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Enabled VMMC2 LDO voltage regulator on TWL4030.
Added GPIO's (power down and reset) for WIFI chip.
Signed-off-by: NAnders Hedlund <anders.j.hedlund@gmail.com>
Signed-off-by: NJonas Zetterberg <jozz@jozz.se>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Signed-off-by: NEnric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add timing data for the Numonyx M65KxxxxAM SDRAM chip, used on the
IGEP v2 board.
Signed-off-by: NEnric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patch adds support for flashes on IGEP v2 boards. For now
only OneNAND is supported.
Signed-off-by: NEnric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Signed-off-by: NEnric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add platform init code for EHCI driver on IGEP v2
Signed-off-by: NEnric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Fix typo on IGEP v2 board
Signed-off-by: NEnric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add platform data for the twl4030_codec MFD on IGEP v2
Signed-off-by: NEnric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Update pandora's regulator setup:
- add new regulators: VAUX2, VAUX4 and VSIM
- add new consumers: ads7846, nub controllers, USB PHY, audio DAC
- use dev names instead of struct device pointers
Signed-off-by: NGrazvydas Ignotas <notasas@gmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patch adds configuration data for DSS2 and sets up
display related regulators.
Signed-off-by: NGrazvydas Ignotas <notasas@gmail.com>
Acked-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

GPIO175 is used for PEN_IRQ on the EVM. This patch
sets the mux settings for the same.
Signed-off-by: NSanjeev Premi <premi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The keypad was not working properly after migrating
to matrix_keypad.

Swapped the row, col fields of the KEY() macro in
the keymap definition to get it working again.
Signed-off-by: NSanjeev Premi <premi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patch sets SYS_NIRQ for keypad input. It also
sets the same as a wakeup event from OFF mode.
Signed-off-by: NSanjeev Premi <premi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Zoom3 board has omap3630 EHCI port2 connected to a ULPI phy.
GPIO_64 is connected to the PHY reset pin.
Signed-off-by: NVikram Pandita <vikram.pandita@ti.com>
Cc: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The check for a valid mux name should be performed regardless of whether
DEBUG_FS is enabled or not. Otherwise without DEBUG_FS, we get:

Unable to handle kernel NULL pointer dereference at virtual address 00000000
pgd = c0004000
[00000000] *pgd=00000000
Internal error: Oops: 5 [#1]
last sysfs file:
Modules linked in:
CPU: 0    Not tainted  (2.6.33-rc8 #10)
PC is at strcmp+0x18/0x40
LR is at omap_mux_init_signal+0x68/0x14c
...

This fixes the issue currently seen with boards not booting up
if DEBUG_FS is not enabled in defconfig.

Note that the earlier ifndef + ifdef now becomes simpler ifdef else:
If CONFIG_OMAP_MUX is selected, we use pin names. If it's not selected,
we only want the GPIO to mux register mapping.
Signed-off-by: NRanjith Lohithakshan <ranjithl@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

sdp4430_uart_config isn't used anywhere, so remove it.
Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add base address definations for new AM35xx IPSS modules, like
VPFE, USBOTG, CPGMAC.

Please note that the OMAP34xx IVA2 memory space is being used for
AM35xx IPSS modules.
Signed-off-by: NVaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: NSriramakrishnan <srk@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Changes for setting the padconf value for sys_nirq line which is
connected to T2 INTR1. This will fix the T2 keypad wakeup.
Signed-off-by: NLesly A M <x0080970@ti.com>
Signed-off-by: NTeerth Reddy <teerth@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Get rid of the ifdeffery in omap_mux_init by creating
omap_mux_init_package and omap_mux_init_signals functions.
Signed-off-by: NTony Lindgren <tony@atomide.com>

EMMC can have two voltage supplies, Vcc and VccQ
which are implemented in the code as consumer
supplies vmmc and vmmc_aux.

If the regulator that supplies vmmc_aux is shared
with other consumers, then sending it to sleep
will disrupt those consumers.  However, the
TWL4030-family regulators may have OFF remapped
to SLEEP, in which case 'regulator_disable()'
will put the regulator to sleep only when all
consumers are disabled - which is the desired
behaviour.

This patch adds a platform data field to allow
that option.
Signed-off-by: NAdrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

An eMMC may be always powered on, so that the lowest
power saving state possible is sleeping. Add a field
to the platform data to indicate that.
Signed-off-by: NAdrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

It has been discovered that, when eMMC is powered off, current
will flow from OMAP eMMC data pull-ups to the eMMC voltage supply.
Configuring pads for OMAP off-mode does not help because eMMC is
powered off independently of OMAP off-mode.  Hence the pads are
now re-configured when eMMC is powered on or off.
Signed-off-by: NAdrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Call the PM context-loss count function, now that there
is a prototype for it.
Signed-off-by: NAdrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

hsmmc.[ch] no longer has any dependency on twl4030
and variable names should be renamed to reflect that.
Signed-off-by: NAdrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

mmc-twl4030.[ch] no longer has any dependency on twl4030
and should be renamed to reflect that.
Signed-off-by: NAdrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patch moves the setup code for GPIO's and Voltage
Regulators from the board file mmc-twl4030.c to the
driver omap_hsmmc.c.  PBIAS and other system control
configuration remains in the board file.

Moving GPIO code to the driver makes the board initialisation
code independent of when GPIO's are defined.  That makes the
board initialisation now entirely independent of its original
twl4030 roots.

Moving Voltage Regulator code to the driver allows for further
development of regulator support in the core MMC code.  It also
permits the MMC core to be compiled as a module, because the
board code no longer calls MMC core functions.
Signed-off-by: NAdrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patch adds support for flashes on 3430SDP boards. All three
NAND, NOR and OneNAND are supported. I have tested it on
3430SDP (ES2 and ES3.1).

This patch can be treated as an example to "how to utilize":
'gpmc-nand.c' and 'board-sdp-flash.c'.

Similar patches can be created for 2430sdp and 3630sdp or any other
similar board.
Signed-off-by: NVimal Singh <vimalsingh@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patch adds 'board-sdp-flash.c', which could be utilized
by boards similar to 3430SDP. (For ex: 2430sdp, 36030sdp).

This file does initialization for all three flash devices present
in SDP boards (NOR, NAND, OneNAND), by finding there 'cs' number
dynamically using switch setting information (S8: 1-4).
This also expects partition information from core board files (for
ex: board-3430sdp.c). Which allows to choose different default
partitions for different boards.

A new structure is created for this purpose: 'flash_partitions'
in 'mach/board-sdp.h'. This has two members:
1. struct mtd_partition *parts
2. int nr_parts

A board file is expected to fill this structure and pass it to
'sdp-flsash-init'. Partition information should be passed in
structure array of 'flash_partitions'. Partition information should
be passed in below sequence in array:
NOR
OneNAND
NAND
Signed-off-by: NVimal Singh <vimalsingh@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Introducing 'gpmc-nand.c' for GPMC specific NAND init.
For example: GPMC timing parameters and all.
This patch also migrates gpmc related calls from 'nand/omap2.c'
to 'gpmc-nand.c'.
Signed-off-by: NVimal Singh <vimalsingh@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

No logical code change

Fix coding style indentaion as per checkpatch.pl
Fix multi-line comment style reported by Nishanth Menon
Signed-off-by: NVikram Pandita <vikram.pandita@ti.com>
Cc: Nishanth Menon <nm@ti.com>
Acked-by: NKevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Get rid of the following warnings:

arch/arm/mach-omap2/gpmc.c:550:30: warning: non-ANSI
function declaration of function 'omap3_gpmc_save_context'

arch/arm/mach-omap2/gpmc.c:581:33: warning: non-ANSI
function declaration of function 'omap3_gpmc_restore_context'
Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Change %d to %ld to avoid the compile warning.
Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>