- 11 11月, 2014 2 次提交
-
-
由 Liad Kaufman 提交于
The length counting previously done had an error in it, causing the length down the data dumping function to be shorter than it should be, causing the end of the data to get truncated off and lost. Cc: <stable@vger.kernel.org> [3.17+] Fixes: 67c65f2c ("iwlwifi: dump periphery registers to fw-error-dump") Signed-off-by: NLiad Kaufman <liad.kaufman@intel.com> Reviewed-by: NJohannes Berg <johannes.berg@intel.com> Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
由 Emmanuel Grumbach 提交于
This code existed but not for all the different FW APIs we support. Fix this. Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
- 03 11月, 2014 1 次提交
-
-
由 Emmanuel Grumbach 提交于
If the RFkill interrupt fires while we calibrate, it would make the firmware fail and the driver wasn't able to recover. Change the flow so that the driver will kill the firmware in that case. Since we have now two flows that are calling trans_stop_device (the RFkill interrupt and the op_mode_mvm_start function) - we need to better sync this. Use the STATUS_DEVICE_ENABLED in the pcie transport in an atomic way to achieve this. This fixes: https://bugzilla.kernel.org/show_bug.cgi?id=86231 CC: <stable@vger.kernel.org> [3.10+] Reviewed-by: NJohannes Berg <johannes.berg@intel.com> Reviewed-by: NLuciano Coelho <luciano.coelho@intel.com> Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
- 29 10月, 2014 1 次提交
-
-
由 Emmanuel Grumbach 提交于
mvm->cur_ucode wasn't set before we actually load the firmware. This caused issues when we boot in RFKILL since we get an RFKILL interrupt upon boot even before we load any firmware. This leads to issues since iwl_mvm_set_hw_rfkill_state (the RFKILL interrupts handler in mvm) relies on this variable. Fix this. Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
- 24 10月, 2014 9 次提交
-
-
由 Emmanuel Grumbach 提交于
iwl_poll_bit may return a strictly positive value when the poll doesn't match on the first try. This was caught when WoWLAN started failing upon resume even if the poll_bit actually succeeded. Also change a wrong print. If we reach the end of iwl_pcie_prepare_card_hw, it means that we couldn't get the devices. Reviewed-by: NJohannes Berg <johannes.berg@intel.com> Reviewed-by: NLuciano Coelho <luciano.coelho@intel.com> Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
由 Emmanuel Grumbach 提交于
This reverts commit aa11bbf3. This commit was causing connection issues and is not needed if IWL_MVM_RS_RSSI_BASED_INIT_RATE is set to false by default. Regardless of the issues mentioned above, this patch added the following WARNING: WARNING: CPU: 0 PID: 3946 at drivers/net/wireless/iwlwifi/mvm/tx.c:190 iwl_mvm_set_tx_params+0x60a/0x6f0 [iwlmvm]() Got an HT rate for a non data frame 0x8 CPU: 0 PID: 3946 Comm: wpa_supplicant Tainted: G O 3.17.0+ #6 Hardware name: LENOVO 20ANCTO1WW/20ANCTO1WW, BIOS GLET71WW (2.25 ) 07/02/2014 0000000000000009 ffffffff814fa911 ffff8804288db8f8 ffffffff81064f52 0000000000001808 ffff8804288db948 ffff88040add8660 ffff8804291b5600 0000000000000000 ffffffff81064fb7 ffffffffa07b73d0 0000000000000020 Call Trace: [<ffffffff814fa911>] ? dump_stack+0x41/0x51 [<ffffffff81064f52>] ? warn_slowpath_common+0x72/0x90 [<ffffffff81064fb7>] ? warn_slowpath_fmt+0x47/0x50 [<ffffffffa07a39ea>] ? iwl_mvm_set_tx_params+0x60a/0x6f0 [iwlmvm] [<ffffffffa07a3cf8>] ? iwl_mvm_tx_skb+0x48/0x3c0 [iwlmvm] [<ffffffffa079cb9b>] ? iwl_mvm_mac_tx+0x7b/0x180 [iwlmvm] [<ffffffffa0746ce9>] ? __ieee80211_tx+0x2b9/0x3c0 [mac80211] [<ffffffffa07492f3>] ? ieee80211_tx+0xb3/0x100 [mac80211] [<ffffffffa0749c49>] ? ieee80211_subif_start_xmit+0x459/0xca0 [mac80211] [<ffffffff814116e7>] ? dev_hard_start_xmit+0x337/0x5f0 [<ffffffff81430d46>] ? sch_direct_xmit+0x96/0x1f0 [<ffffffff81411ba3>] ? __dev_queue_xmit+0x203/0x4f0 [<ffffffff8142f670>] ? ether_setup+0x70/0x70 [<ffffffff814e96a1>] ? packet_sendmsg+0xf81/0x1110 [<ffffffff8140625c>] ? skb_free_datagram+0xc/0x40 [<ffffffff813f7538>] ? sock_sendmsg+0x88/0xc0 [<ffffffff813f7274>] ? move_addr_to_kernel.part.20+0x14/0x60 [<ffffffff811c47c2>] ? __inode_wait_for_writeback+0x62/0xb0 [<ffffffff813f7a91>] ? SYSC_sendto+0xf1/0x180 [<ffffffff813f88f9>] ? __sys_recvmsg+0x39/0x70 [<ffffffff8150066d>] ? system_call_fastpath+0x1a/0x1f ---[ end trace cc19a150d311fc63 ]--- which was reported here: https://bugzilla.kernel.org/show_bug.cgi?id=85691 CC: <stable@vger.kernel.org> [3.13+] Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
由 Emmanuel Grumbach 提交于
When mac80211 wants to ensure that a frame is sent, it calls the flush() callback. Until now, iwldvm implemented this by waiting that all the frames are sent (ACKed or timeout). In case of weak signal, this can take a significant amount of time, delaying the next connection (in case of roaming). Many users have reported that the flush would take too long leading to the following error messages to be printed: iwlwifi 0000:03:00.0: fail to flush all tx fifo queues Q 2 iwlwifi 0000:03:00.0: Current SW read_ptr 161 write_ptr 201 iwl data: 00000000: 00 00 00 00 00 00 00 00 fe ff 01 00 00 00 00 00 [snip] iwlwifi 0000:03:00.0: FH TRBs(0) = 0x00000000 [snip] iwlwifi 0000:03:00.0: Q 0 is active and mapped to fifo 3 ra_tid 0x0000 [9,9] [snip] Instead of waiting for these packets, simply drop them. This significantly improves the responsiveness of the network. Note that all the queues are flushed, but the VO one. This is not typically used by the applications and it likely contains management frames that are useful for connection or roaming. This bug is tracked here: https://bugzilla.kernel.org/show_bug.cgi?id=56581 But it is duplicated in distributions' trackers. A simple search in Ubuntu's database led to these bugs: https://bugs.launchpad.net/ubuntu/+source/linux-firmware/+bug/1270808 https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1305406 https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1356236 https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1360597 https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1361809 Cc: <stable@vger.kernel.org> Depends-on: 77be2c54 ("mac80211: add vif to flush call") Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
由 Matti Gottlieb 提交于
Don't add the time event to the list. We added it several times the same time event, which leads to an infinite loop when walking the list. Since we (currently) don't support more than one ROC for STA vif at a time, enforce this and don't add the time event to any list. We were also missing the locking of the mutex which led to a lockdep splat - fix that. Signed-off-by: NMatti Gottlieb <matti.gottlieb@intel.com> Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
由 Haim Dreyfuss 提交于
The tx power should be limited from many reasons. currently, setting the tx power is available by the mvm only for station interface. Adding the tx power condition to bss_info_changed_ap_ibss make it available also for AP. Signed-off-by: NHaim Dreyfuss <haim.dreyfuss@intel.com> Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
由 Emmanuel Grumbach 提交于
The probe requests sent during scan must get BT prio 3. Fix that. Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
由 Emmanuel Grumbach 提交于
Cc: <stable@vger.kernel.org> [3.16+] Fixes: 2adc8949 ("iwlwifi: mvm: BT Coex - fix boost register / LUT values") Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
由 Liad Kaufman 提交于
I changed the string but forgot to update the fix also to MODULE_FIRMWARE(). Signed-off-by: NLiad Kaufman <liad.kaufman@intel.com> Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
由 Emmanuel Grumbach 提交于
The LTR is the handshake between the device and the root complex about the latency allowed when the bus exits power save. This configuration was missing and this led to high latency in the link power up. The end user could experience high latency in the network because of this. Cc: <stable@vger.kernel.org> [3.10+] Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
- 09 10月, 2014 27 次提交
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next由 Linus Torvalds 提交于
Pull networking updates from David Miller: "Most notable changes in here: 1) By far the biggest accomplishment, thanks to a large range of contributors, is the addition of multi-send for transmit. This is the result of discussions back in Chicago, and the hard work of several individuals. Now, when the ->ndo_start_xmit() method of a driver sees skb->xmit_more as true, it can choose to defer the doorbell telling the driver to start processing the new TX queue entires. skb->xmit_more means that the generic networking is guaranteed to call the driver immediately with another SKB to send. There is logic added to the qdisc layer to dequeue multiple packets at a time, and the handling mis-predicted offloads in software is now done with no locks held. Finally, pktgen is extended to have a "burst" parameter that can be used to test a multi-send implementation. Several drivers have xmit_more support: i40e, igb, ixgbe, mlx4, virtio_net Adding support is almost trivial, so export more drivers to support this optimization soon. I want to thank, in no particular or implied order, Jesper Dangaard Brouer, Eric Dumazet, Alexander Duyck, Tom Herbert, Jamal Hadi Salim, John Fastabend, Florian Westphal, Daniel Borkmann, David Tat, Hannes Frederic Sowa, and Rusty Russell. 2) PTP and timestamping support in bnx2x, from Michal Kalderon. 3) Allow adjusting the rx_copybreak threshold for a driver via ethtool, and add rx_copybreak support to enic driver. From Govindarajulu Varadarajan. 4) Significant enhancements to the generic PHY layer and the bcm7xxx driver in particular (EEE support, auto power down, etc.) from Florian Fainelli. 5) Allow raw buffers to be used for flow dissection, allowing drivers to determine the optimal "linear pull" size for devices that DMA into pools of pages. The objective is to get exactly the necessary amount of headers into the linear SKB area pre-pulled, but no more. The new interface drivers use is eth_get_headlen(). From WANG Cong, with driver conversions (several had their own by-hand duplicated implementations) by Alexander Duyck and Eric Dumazet. 6) Support checksumming more smoothly and efficiently for encapsulations, and add "foo over UDP" facility. From Tom Herbert. 7) Add Broadcom SF2 switch driver to DSA layer, from Florian Fainelli. 8) eBPF now can load programs via a system call and has an extensive testsuite. Alexei Starovoitov and Daniel Borkmann. 9) Major overhaul of the packet scheduler to use RCU in several major areas such as the classifiers and rate estimators. From John Fastabend. 10) Add driver for Intel FM10000 Ethernet Switch, from Alexander Duyck. 11) Rearrange TCP_SKB_CB() to reduce cache line misses, from Eric Dumazet. 12) Add Datacenter TCP congestion control algorithm support, From Florian Westphal. 13) Reorganize sk_buff so that __copy_skb_header() is significantly faster. From Eric Dumazet" * git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1558 commits) netlabel: directly return netlbl_unlabel_genl_init() net: add netdev_txq_bql_{enqueue, complete}_prefetchw() helpers net: description of dma_cookie cause make xmldocs warning cxgb4: clean up a type issue cxgb4: potential shift wrapping bug i40e: skb->xmit_more support net: fs_enet: Add NAPI TX net: fs_enet: Remove non NAPI RX r8169:add support for RTL8168EP net_sched: copy exts->type in tcf_exts_change() wimax: convert printk to pr_foo() af_unix: remove 0 assignment on static ipv6: Do not warn for informational ICMP messages, regardless of type. Update Intel Ethernet Driver maintainers list bridge: Save frag_max_size between PRE_ROUTING and POST_ROUTING tipc: fix bug in multicast congestion handling net: better IFF_XMIT_DST_RELEASE support net/mlx4_en: remove NETDEV_TX_BUSY 3c59x: fix bad split of cpu_to_le32(pci_map_single()) net: bcmgenet: fix Tx ring priority programming ...
-
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc由 Linus Torvalds 提交于
Pull ARM64 SoC changes from Arnd Bergmann: "Starting with 3.18, we are merging SoC-specific changes for arm64 through the arm-soc tree, like we have been doing for arm32. This time, there is only one set of changes, adding support for the Cavium "Thunder" Soc family. Since the changes are relatively small, this includes Kconfig, defconfig and DT changes. If all goes well, we will never require adding actual C source code for platform support in arm64, given that the architecture is more clearly defined and we have moved out a lot of the platform specifics into device drivers for arm32 already" * tag 'arm64-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: arm64, defconfig: Enable Cavium Thunder SoC in defconfig arm64, thunder: Add Kconfig option for Cavium Thunder SoC Family arm64, thunder: Document devicetree bindings for Cavium Thunder SoC arm64, thunder: Add initial dts for Cavium Thunder SoC
-
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc由 Linus Torvalds 提交于
Pull ARM SoC defconfig changes from Arnd Bergmann: "This is a collection of the various changes to defconfig files, most importantly enabling some additional platforms in the multi_v7_defconfig file" * tag 'defconfig-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (40 commits) ARM: configs: fix duplicate entry in multi_v7 ARM: multi_v7_defconfig: add missing Tegra options ARM: bcm2835: enable USB_DWC2_HOST in defconfig ARM: meson: update multi_v7_defconfig ARM: multi_v7_defconfig: Enable Mediatek platform ARM: qcom: Update defconfig ARM: mvebu: add gpio-fan to mvebu_v7_defconfig ARM: mvebu: add LED class support built-in in mvebu_v7_defconfig ARM: shmobile: Enable r8a7794 SoC in shmobile_defconfig ARM: LPC32xx: defconfig update ARM: configs: Enable cpufreq-cpu0 for multi_v7_defconfig ARM: configs: Remove REGULATOR_VIRTUAL_CONSUMER from defconfigs ARM: tegra: enable Atmel touchpad in defconfig ARM: at91: sama5: update defconfig ARM: at91: at91sam9rl: update defconfig ARM: at91: at91sam9g45: update defconfig ARM: at91: at91sam9263: update defconfig ARM: at91: at91sam9261_9g10: update defconfig ARM: at91: at91sam9260_9g20: update defconfig ARM: at91: at91_dt: update defconfig ...
-
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc由 Linus Torvalds 提交于
Pull ARM SoC driver updates from Arnd Bergmann: "These are changes for drivers that are intimately tied to some SoC and for some reason could not get merged through the respective subsystem maintainer tree. Most of the new code is for the Keystone Navigator driver, which is new base support that is going to be needed for their hardware accelerated network driver and other units. Most of the commits are for moving old code around from at91 and omap for things that are done in device drivers nowadays. - at91: move reset, poweroff, memory and clocksource code into drivers directories - socfpga: add edac driver (through arm-soc, as requested by Boris) - omap: move omap-intc code to drivers/irqchip - sunxi: added an RTC driver for sun6i - omap: mailbox driver related changes - keystone: support for the "Navigator" component - versatile: new reboot, led and soc drivers" * tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (92 commits) bus: arm-ccn: Fix spurious warning message leds: add device tree bindings for register bit LEDs soc: add driver for the ARM RealView power: reset: driver for the Versatile syscon reboot leds: add a driver for syscon-based LEDs drivers/soc: ti: fix build break with modules MAINTAINERS: Add Keystone Multicore Navigator drivers entry soc: ti: add Keystone Navigator DMA support Documentation: dt: soc: add Keystone Navigator DMA bindings soc: ti: add Keystone Navigator QMSS driver Documentation: dt: soc: add Keystone Navigator QMSS bindings rtc: sunxi: Depend on platforms sun4i/sun7i that actually have the rtc rtc: sun6i: Add sun6i RTC driver irqchip: omap-intc: remove unnecessary comments irqchip: omap-intc: correct maximum number or MIR registers irqchip: omap-intc: enable TURBO idle mode irqchip: omap-intc: enable IP protection irqchip: omap-intc: remove unnecesary of_address_to_resource() call irqchip: omap-intc: comment style cleanup irqchip: omap-intc: minor improvement to omap_irq_pending() ...
-
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc由 Linus Torvalds 提交于
Pull ARM SoC DT updates from Arnd Bergmann: "As usual, this is the largest branch, though this time a little under half of the total changes with 307 individual non-merge changesets. The largest changes are the addition of new machines, in particular the Tegra based Chromebook, the Renesas r8a7794 SoC, and DT support for the old i.MX1 platform. Other changes include - at91: various sam9 and sama5 updates - exynos: much extended Peach Pi/Pit (Chromebook 2) support - keystone: new peripherals - meson: added DT for meson6 SoC - mvebu: new device support for Armada 370/375 - qcom: improved support for IPQ8064 and MSM8x60 - rockchip: much improved support for rk3288 - shmobile: lots of updates all over the place - sunxi: dts license change - sunxi: more a23 device support - vexpress: CLCD DT description" * tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (308 commits) ARM: DTS: meson: update DTSI to add watchdog node ARM: dts: keystone-k2l: fix mdio io start address ARM: dts: keystone-k2e: fix mdio io start address ARM: dts: keystone-k2e: update usb1 node for dma properties ARM: dts: keystone: fix io range for usb_phy0 Revert "Merge tag 'hix5hd2-dt-for-3.18' of git://github.com/hisilicon/linux-hisi into next/dt" Revert "ARM: dts: hix5hd2: add wdg node" ARM: dts: add rk3288 i2s controller ARM: vexpress: Add CLCD Device Tree properties ARM: bcm2835: add I2S pinctrl to device tree ARM: meson: documentation: add bindings documentation ARM: meson: dts: add basic Meson/Meson6/Meson6-atv1200 DTSI/DTS ARM: dts: mt6589: Change compatible string for GIC ARM: dts: mediatek: Add compatible property for aquaris5 ARM: dts: mt6589-aquaris5: Add boot argument earlyprintk ARM: dts: mt6589: Fix typo in GIC unit address ARM: dts: Build dtb for Mediatek board ARM: dts: keystone: fix bindings for pcie and usb clock nodes ARM: dts: keystone: k2l: Fix chip selects for SPI devices ARM: dts: keystone: add dsp gpio controllers nodes ...
-
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc由 Linus Torvalds 提交于
Pull ARM SoC platform changes from Arnd Bergmann: "New and updated SoC support. Among the things new for this release are: - at91: Added support for the new SAMA5D4 SoC, following the earlier SAMA5D3 - bcm: Added support for BCM63XX family of DSL SoCs - hisi: Added support for HiP04 server-class SoC - meson: Initial support for the Amlogic Meson6 (aka 8726MX) platform - shmobile: added support for new r8a7794 (R-Car E2) automotive SoC Noteworthy changes to existing SoC support are: - imx: convert i.MX1 to device tree - omap: lots of power management work - omap: base support to enable moving to standard UART driver - shmobile: lots of progress for multiplatform support, still ongoing" * tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (171 commits) ARM: hisi: depend on ARCH_MULTI_V7 CNS3xxx: Fix debug UART. ARM: at91: fix nommu build regression ARM: meson: add basic support for MesonX SoCs ARM: meson: debug: add debug UART for earlyprintk support irq: Export handle_fasteoi_irq ARM: mediatek: Add earlyprintk support for mt6589 ARM: hisi: Fix platmcpm compilation when ARMv6 is selected ARM: debug: fix alphanumerical order on debug uarts ARM: at91: document Atmel SMART compatibles ARM: at91: add sama5d4 support to sama5_defconfig ARM: at91: dt: add device tree file for SAMA5D4ek board ARM: at91: dt: add device tree file for SAMA5D4 SoC ARM: at91: SAMA5D4 SoC detection code and low level routines ARM: at91: introduce basic SAMA5D4 support clk: at91: add a driver for the h32mx clock ARM: pxa3xx: provide specific platform_devices for all ssp ports ARM: pxa: ssp: provide platform_device_id for PXA3xx ARM: OMAP4+: Remove static iotable mappings for SRAM ARM: OMAP4+: Move SRAM data to DT ...
-
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc由 Linus Torvalds 提交于
Pull ARM SoC cleanups from Arnd Bergmann: "This time around, the cleanup branch contains mostly code removal. A number of board files for at91, imx and msm have become obsolete because of the DT conversion and are now ready to be removed. The OMAP platform has traditionally had its own DMA engine abstraction and as this is being phased out, a lot of the original code is now unused and can be removed as well. S3C24xx can be simplified now that the restart code is a proper device driver. Finally, a number of cleanups in shmobile are done to prepare for the addition of new code in other branches" * tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (43 commits) ARM: at91: Remove the support for the RSI EWS board arm: mach-omap2: Convert pr_warning to pr_warn ARM: OMAP: Remove unused pieces of legacy DMA API ARM: at91: remove board file for Acme Systems Fox G20 ARM: orion5x: Convert pr_warning to pr_warn ARM: S3C24XX: remove separate restart code ARM: EXYNOS: Do not calculate boot address twice ARM: sunxi: Remove sun4i reboot code from mach directory ARM: imx: Remove mach-mxt_td60 board file ARM: shmobile: armadillo800eva legacy: Use rmobile_add_devices_to_domains() ARM: shmobile: r8a7740: Clean up pm domain table ARM: shmobile: r8a7740: Use rmobile_add_devices_to_domains() ARM: shmobile: sh7372: Make domain_devices[] static __initdata ARM: shmobile: mackerel: Make domain_devices[] static __initdata clocksource: tcb_clksrc: sanitize IRQ request ARM: at91/tclib: mask interruptions at shutdown and probe ARM: at91/tclib: move initialization from alloc to probe ARM: at91/tclib: prefer using of devm_* functions ARM: clps711x: Switch CLPS711X subarch to use clk and clocksource driver ARM: shmobile: r8a7791 is now called "R-Car M2-W" ...
-
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc由 Linus Torvalds 提交于
Pull ARM SoC non-critical bug fixes from Arnd Bergmann: "These are bug fixes for harmless problems that were not important enough to get fixed in 3.17. The majority of these are OMAP specific, but there are also a couple for Marvell mvebu, cns3xxx, and others, as well as some updates for the MAINTAINERS file. In particular, Robert Jarzmik and Daniel Mack now volunteered to help out maintaining the PXA platform, Krzysztof Halasa took over the cns3xxx platform, Carlo Caione is the maintainer for the new Amlogic meson platform, and Matthias Brugger is now listed for the mediatek platform he recently contributed" * tag 'fixes-nc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (42 commits) MAINTAINERS: update Shawn's email address MAINTAINERS: condense some Tegra related entries MAINTAINERS: add Alexandre Courbot for Tegra MAINTAINERS: CNS3xxx and IXP4xx update. MAINTAINERS: Add maintainers entry for Mediatek SoCs arm, vt8500, LLVMLlinux: Use mcr instead of mcr% for mach-vt8500 MAINTAINERS: add a third maintainer to mach-bcm CNS3xxx: Fix PCIe read size limit. CNS3xxx: Fix logical PCIe topology. CNS3xxx: Fix debug UART. MAINTAINERS: Add entry for the Amlogic MesonX SoCs MAINTAINERS: update ARM pxa maintainers ARM: at91/PMC: don't forget to write PMC_PCDR register to disable clocks ARM: at91: fix at91sam9263ek DT mmc pinmuxing settings ARM: mvebu: Netgear RN102: Use Hardware BCH ECC ARM: Kirkwood: Fix DT based DSA. ARM: OMAP2+: make of_device_ids const ARM: omap2: make arrays containing machine compatible strings const ARM: LPC32xx: Fix reset function ARM: mvebu: Netgear RN2120: Use Hardware BCH ECC ...
-
由 Fabian Frederick 提交于
No need to store netlbl_unlabel_genl_init result and test it before returning. Signed-off-by: NFabian Frederick <fabf@skynet.be> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Eric Dumazet 提交于
Add two helpers so that drivers do not have to care of BQL being available or not. Signed-off-by: NEric Dumazet <edumazet@google.com> Reported-by: NJim Davis <jim.epost@gmail.com> Fixes: 29d40c90 ("net/mlx4_en: Use prefetch in tx path") Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Masanari Iida 提交于
In commit 7bced397, dma_cookie was removed from struct skbuff. But the description of dma_cookie still exist. So the "make xmldocs" output following warning. Warning(.//include/linux/skbuff.h:609): Excess struct/union /enum/typedef member 'dma_cookie' description in 'sk_buff' Remove description of dma_cookie fix the symptom. Signed-off-by: NMasanari Iida <standby24x7@gmail.com> Acked-by: NDan Williams <dan.j.williams@intel.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Dan Carpenter 提交于
The tx_desc struct holds 8 __be64 values. The original code in ring_tx_db() took a tx_desc pointer then casted it to an int pointer and then casted it to a u64 pointer. It was confusing and triggered some static checker warnings. I have changed the cxgb_pio_copy() function to only take tx_desc pointers. This isn't really a loss of flexibility because anything else was buggy to begin with. I also removed the casting on the destination pointer since that was unnecessary and a bit messy. Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Dan Carpenter 提交于
"cntxt_id" is an unsigned int but "udb" is a u64 so there is a potential shift wrapping bug here. Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Eric Dumazet 提交于
Support skb->xmit_more in i40e is straightforward : we need to move around i40e_maybe_stop_tx() call to correctly test netif_xmit_stopped() before taking the decision to not kick the NIC. Signed-off-by: NEric Dumazet <edumazet@google.com> Signed-off-by: NDaniel Borkmann <dborkman@redhat.com> Acked-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 David S. Miller 提交于
Christophe Leroy says: ==================== net: fs_enet: Remove non NAPI RX and add NAPI for TX When using a MPC8xx as a router, 'perf' shows a significant time spent in fs_enet_interrupt() and fs_enet_start_xmit(). 'perf annotate' shows that the time spent in fs_enet_start_xmit is indeed spent between spin_unlock_irqrestore() and the following instruction, hence in interrupt handling. This is due to the TX complete interrupt that fires after each transmitted packet. This patchset first remove all non NAPI handling as NAPI has become the only mode for RX, then adds NAPI for handling TX complete. This improves NAT TCP throughput by 21% on MPC885 with FEC. Tested on MPC885 with FEC. [PATCH 1/2] net: fs_enet: Remove non NAPI RX [PATCH 2/2] net: fs_enet: Add NAPI TX Signed-off-by: NChristophe Leroy <christophe.leroy@c-s.fr> ==================== Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 LEROY Christophe 提交于
When using a MPC8xx as a router, 'perf' shows a significant time spent in fs_enet_interrupt() and fs_enet_start_xmit(). 'perf annotate' shows that the time spent in fs_enet_start_xmit is indeed spent between spin_unlock_irqrestore() and the following instruction, hence in interrupt handling. This is due to the TX complete interrupt that fires after each transmitted packet. This patch modifies the handling of TX complete to use NAPI. With this patch, my NAT router offers a throughput improved by 21% Original performance: [root@localhost tmp]# scp toto pgs:/tmp toto 100% 256MB 2.8MB/s 01:31 Performance with the patch: [root@localhost tmp]# scp toto pgs:/tmp toto 100% 256MB 3.4MB/s 01:16 Signed-off-by: NChristophe Leroy <christophe.leroy@c-s.fr> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 LEROY Christophe 提交于
In the probe function, use_napi is inconditionnaly set to 1. This patch removes all the code which is conditional to !use_napi, and removes use_napi which has then become useless. Signed-off-by: NChristophe Leroy <christophe.leroy@c-s.fr> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Chun-Hao Lin 提交于
RTL8168EP is Realtek PCIe Gigabit Ethernet controller with DASH support. It is a successor chip of RTL8168DP. For RTL8168EP, the read/write ocp register is via eri channel type 2, so I move ocp_xxx() related functions under rtl_eri_xxx. And use r8168dp_ocp_xxx() for RTL8168DP ocp read/write, r8168ep_ocp_xxx() for RTL8168EP ocp read/write. The way of checking dash enable is different with RTL8168DP. I use r8168dp_check_dash()for RTL8168DP and r8168ep_check_dash() for RTL8168EP, to check if dash is enabled. The driver_start() and driver_stop() of RTL8168EP is also different with RTL8168DP. I use rtl8168dp_driver_xxx() for RTL8168DP and rtl8168ep_driver_xxx for RTL8168EP. Right now, RTL8168EP phy mcu did not need firmware code patch, so I did not add firmware code for it. so I did not add firmware code for it. Signed-off-by: NChun-Hao Lin <hau@realtek.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 WANG Cong 提交于
We need to copy exts->type when committing the change, otherwise it would be always 0. This is a quick fix for -net and -stable, for net-next tcf_exts will be removed. Fixes: commit 33be6271 ("net_sched: act: use standard struct list_head") Reported-by: NJamal Hadi Salim <jhs@mojatatu.com> Cc: Jamal Hadi Salim <jhs@mojatatu.com> Cc: John Fastabend <john.fastabend@gmail.com> Signed-off-by: NCong Wang <xiyou.wangcong@gmail.com> Acked-by: NJamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Pawel Moll 提交于
Because CCN's cycle counter always runs, it will generate an interrupt on overflow even if the relevant perf event was not requested, causing a spurious warning message. Fixed now by warning on only normal counter unwanted overflows. Also cleaning the overflow mask at init now, not to warn on event previously requested by firmware. Signed-off-by: NPawel Moll <pawel.moll@arm.com> Signed-off-by: NOlof Johansson <olof@lixom.net> Signed-off-by: NArnd Bergmann <arnd@arndb.de>
-
由 Shawn Guo 提交于
My Freescale email address will be gone shortly. Update my email to be the Linaro one. Signed-off-by: NShawn Guo <shawn.guo@freescale.com> Signed-off-by: NArnd Bergmann <arnd@arndb.de>
-
由 Stephen Warren 提交于
There's little point having specific entries in MAINTAINERS for Tegra drivers that are already covered by the top-level Tegra architecture support entry, and maintained by people listed there. Remove the duplicates. Signed-off-by: NStephen Warren <swarren@nvidia.com> Acked-by: NThierry Reding <treding@nvidia.com> Signed-off-by: NArnd Bergmann <arnd@arndb.de>
-
由 Stephen Warren 提交于
I'd like to propose Alexandre Courbot as an additional Tegra maintainer. He's been working on a variety of Tegra-related code for a while, and is now officially tasked with working on upstream support. Signed-off-by: NStephen Warren <swarren@nvidia.com> Acked-by: NAlexandre Courbot <acourbot@nvidia.com> Acked-by: NThierry Reding <treding@nvidia.com> -- v2: * Use Alexandre's full name. * Use a non-NVIDIA email address to avoid Exchange Server patch corruption. Signed-off-by: NArnd Bergmann <arnd@arndb.de>
-
https://github.com/carlocaione/linux-meson由 Arnd Bergmann 提交于
Merge "Meson6 WDT support" from Carlo Caione: This patch adds the support for the Meson6 watchdog in the DTSI * tag 'meson-wdt-dt-3.18' of https://github.com/carlocaione/linux-meson: ARM: DTS: meson: update DTSI to add watchdog node Signed-off-by: NArnd Bergmann <arnd@arndb.de>
-
git://git.kernel.org/pub/scm/linux/kernel/git/jaegeuk/f2fs由 Linus Torvalds 提交于
Pull f2fs updates from Jaegeuk Kim: "This patch-set introduces a couple of new features such as large sector size, FITRIM, and atomic/volatile writes. Several patches enhance power-off recovery and checkpoint routines. The fsck.f2fs starts to support fixing corrupted partitions with recovery hints provided by this patch-set. Summary: - retain some recovery information for fsck.f2fs - enhance checkpoint speed - enhance flush command management - bug fix for lseek - tune in-place-update policies - enhance roll-forward speed - revisit all the roll-forward and fsync rules - support larget sector size - support FITRIM - support atomic and volatile writes And several clean-ups and bug fixes are included" * tag 'f2fs-for-3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/jaegeuk/f2fs: (42 commits) f2fs: support volatile operations for transient data f2fs: support atomic writes f2fs: remove unused return value f2fs: clean up f2fs_ioctl functions f2fs: potential shift wrapping buf in f2fs_trim_fs() f2fs: call f2fs_unlock_op after error was handled f2fs: check the use of macros on block counts and addresses f2fs: refactor flush_nat_entries to remove costly reorganizing ops f2fs: introduce FITRIM in f2fs_ioctl f2fs: introduce cp_control structure f2fs: use more free segments until SSR is activated f2fs: change the ipu_policy option to enable combinations f2fs: fix to search whole dirty segmap when get_victim f2fs: fix to clean previous mount option when remount_fs f2fs: skip punching hole in special condition f2fs: support large sector size f2fs: fix to truncate blocks past EOF in ->setattr f2fs: update i_size when __allocate_data_block f2fs: use MAX_BIO_BLOCKS(sbi) f2fs: remove redundant operation during roll-forward recovery ...
-
git://linux-nfs.org/~bfields/linux由 Linus Torvalds 提交于
Pull nfsd updates from Bruce Fields: "Highlights: - support the NFSv4.2 SEEK operation (allowing clients to support SEEK_HOLE/SEEK_DATA), thanks to Anna. - end the grace period early in a number of cases, mitigating a long-standing annoyance, thanks to Jeff - improve SMP scalability, thanks to Trond" * 'for-3.18' of git://linux-nfs.org/~bfields/linux: (55 commits) nfsd: eliminate "to_delegation" define NFSD: Implement SEEK NFSD: Add generic v4.2 infrastructure svcrdma: advertise the correct max payload nfsd: introduce nfsd4_callback_ops nfsd: split nfsd4_callback initialization and use nfsd: introduce a generic nfsd4_cb nfsd: remove nfsd4_callback.cb_op nfsd: do not clear rpc_resp in nfsd4_cb_done_sequence nfsd: fix nfsd4_cb_recall_done error handling nfsd4: clarify how grace period ends nfsd4: stop grace_time update at end of grace period nfsd: skip subsequent UMH "create" operations after the first one for v4.0 clients nfsd: set and test NFSD4_CLIENT_STABLE bit to reduce nfsdcltrack upcalls nfsd: serialize nfsdcltrack upcalls for a particular client nfsd: pass extra info in env vars to upcalls to allow for early grace period end nfsd: add a v4_end_grace file to /proc/fs/nfsd lockd: add a /proc/fs/lockd/nlm_end_grace file nfsd: reject reclaim request when client has already sent RECLAIM_COMPLETE nfsd: remove redundant boot_time parm from grace_done client tracking op ...
-