DSS, DISPC, DSI, RFBI, VENC baseaddr can be obtained from platform_get_resource().
This API in turn picks the right silicon baseaddr from the hwmod database.
So hardcoding of base addr could be removed.
Reviewed-by: NPaul Walmsley <paul@pwsan.com>
Reviewed-by: NKevin Hilman <khilman@ti.com>
Tested-by: NKevin Hilman <khilman@ti.com>
Signed-off-by: NSumit Semwal <sumit.semwal@ti.com>
Signed-off-by: NSenthilvadivu Guruswamy <svadivu@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

This patch replaces printk's in the init/probe functions to dev_dbg
for boot time optimization.
Reviewed-by: NKevin Hilman <khilman@ti.com>
Tested-by: NKevin Hilman <khilman@ti.com>
Signed-off-by: NSumit Semwal <sumit.semwal@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Hwmod adaptation design requires each of the DSS HW IP to be a platform driver.
So a platform_driver for DSI is created and init exit methods are moved from core.c
to its driver probe,remove. pdev member has to be maintained by its own drivers.

Also, vdds_dsi regulator handling is copied to dsi.c, since vdds_dsi regulator is
needed by dpi_init() too. Board files are updated accordingly to add 2 instances of
vdds_dsi regulator.

DSI platform driver is registered from inside omap_dss_probe, in the order desired.
Signed-off-by: NSenthilvadivu Guruswamy <svadivu@ti.com>
Signed-off-by: NSumit Semwal <sumit.semwal@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

The following dispc functions are also changed to incorporate channel as an argument:
	-dispc_lclk_rate()
	-dispc_pclk_rate()
	-dispc_set_pol_freq()
	-dispc_set_clock_div()
	-dispc_get_clock_div()
Signed-off-by: NSumit Semwal <sumit.semwal@ti.com>
Signed-off-by: NMukund Mittal <mmittal@ti.com>
Signed-off-by: NSamreen <samreen@ti.com>
Signed-off-by: NArchit Taneja <archit@ti.com>
[tomi.valkeinen@nokia.com: fixed trivial compile error]
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

The interface drivers (dsi.c, sdi.c etc) need to call dispc functions with
dssdev->manager->id as a parameter to specify the DISPC channel which they want
to configure/use, this is required as the same functions are now used to configure
dispc registers of different channels.

The following dispc functions are changed to incorporate channel as an argument:
	-dispc_enable_fifohandcheck()
	-dispc_set_lcd_size()
	-dispc_set_parallel_interface_mode()
	-dispc_set_tft_data_lines()
	-dispc_set_lcd_display_type()
	-dispc_set_lcd_timings()
Signed-off-by: NSumit Semwal <sumit.semwal@ti.com>
Signed-off-by: NMukund Mittal <mmittal@ti.com>
Signed-off-by: NSamreen <samreen@ti.com>
Signed-off-by: NArchit Taneja <archit@ti.com>
[tomi.valkeinen@nokia.com: fixed trivial compile error]
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

iounmap is already done in label err2: so extra iounmap in
the error handling path could be removed.
Signed-off-by: NSenthilvadivu Guruswamy <svadivu@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

In the case of an error on calling dsi_update_screen_l4(), a
successful framedone callback is still sent to panel-taal. An
error should be returned to taal_update() instead.
Signed-off-by: NArchit Taneja <archit@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

OMAP DSS HW cannot send updates with odd widths. Normally the widths are
made even while preparing the update.

This patch adds a BUG_ON() to check if the update width is even. This is
to detect broken updates cleanly, as otherwise the OMAP DSS HW will just
halt, leading to obscure error situations.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

The current FIFO low threshold was too low, and caused the FIFO to run
empty when core domain went to INA state between FIFO fills. This patch
increases the low threshold to keep that from happening.

The threshold values depend quite much on the HW and the use cases, so
this should actually be somehow configurable from board files, perhaps.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

The code presumed that all ComplexIO interrupts are errors. This is not
the case. This patch adds proper error mask for CIO interrupt handling.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

SMRPS function always sent BTA after sending the SMRPS packet. This is
not needed, and also caused some (buggy) panels to bug. This patch
removes the BTA.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

Currently the update area on manual update displays is automatically
enlargened to fully cover scaled overlays. This patch makes that
optional, allowing the panel driver to choose if it's used or not.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

Previously a work was started on FRAMEDONE interrupt, and this work
either sent a BTA synchronously or looped until TE_SIZE was zero, to
wait for the end of the transfer.

This patch changes a BTA to be sent asynchronously from FRAMEDONE
interrupt, and when a BTA interrupt is received, the transfer is
finished. This way we do the whole process asynchronously, and also
inside interrupt context.

This will give us much better latency to handle the end of the frame
than with the previous work based solution.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

Change dsi_vc_config_l4/vp() to loop for the VC_BUSY flag to change, and
return an error if it fails.

Busy looping is bad, but there's no interrupt that can be used for all the
cases where VC can be busy. So the caller should first try to make sure
that the VC is not busy, if possible, and then call dsi_vc_config_l4/vp().

Most notable case when the caller cannot be sure if the VC is busy is
after frame has been sent. Usually DSI buffers have been emptied until we
need to reconfig the VC, but in some rare cases the VC can still be busy,
and this patch will handle that case.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

Once the DSI PLL is separated from the DSI display a full DSI reset will
not be performed every time the display is enabled so the interface and
VCs must be disabled when disabling the display. If the VCs are not
disabled some register accesses will abort.
Signed-off-by: NVille Syrjälä <ville.syrjala@nokia.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

The TRM tells us to wait for the DSI PLL derived clocks to become
active before selecting them for use. I didn't actually have any issues
which this would fix but according to the TRM it seems to be the right
thing to do.
Signed-off-by: NVille Syrjälä <ville.syrjala@nokia.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

Print an error message if dsi_calc_clock_rates() fails just like it's
done when dispc_calc_clock_rates() fails.
Signed-off-by: NVille Syrjälä <ville.syrjala@nokia.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

Do not leave the free running pixel clock enabled if the DSI PLL reset
times out.
Signed-off-by: NVille Syrjälä <ville.syrjala@nokia.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

Using nanoseconds as arguments to functions that set the DSI timeouts was
perhaps not so good idea. The timeouts are based on different DSI clocks,
so the possible range for the timeouts vary greatly depending on the
clocks. Also, the multipliers used with the timeouts cause big gaps in the
timeout range, meaning that the nanosecond based functions could cause the
timeout to be quite far from the intended value.

This patch changes the functions to take the plain tick values with the
multiplier enable/disable bits, and sets the TA/LP_RX/HS_TX timeouts to
maximum. While the timeouts could be much lower, the fact is that when
TA/LP_RX/HS_TX timeout happens, we are in an error situation and not in a
hurry anyway.

STOP_STATE_COUNTER is a different matter, but it is only used at
initialization time, and won't normally affect the performance.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

Check if the peripheral answered something, and if so, dump the data
and return an error.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

Change dsi_vc_dcs_read_2() data parameter to two u8 parameters to make the
byte-order clear.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

Using the shared workqueue led to to a deadlock in the case where the
display was unblanked via keyboard.

What happens is something like this:

- User presses a key

context 1:
- drivers/char/keyboard.c calls schedule_console_callback()
- fb_unblank takes the console semaphore
- dsi bus lock is taken, and frame transfer is started (dsi bus lock is
  left on)
- Unblank code tries to set the panel backlight, which tries to take dsi
  bus lock, but is blocked while the frame transfer is going on

context 2, shared workqueue, console_callback in drivers/char/vt.c:
- Tries to take console semaphore
- Blocks, as console semaphore is being held by context 1
- No other shared workqueue work can be run

context 3, HW irq, caused by FRAMEDONE interrupt:
- Interrupt handler schedules framedone-work in shared workqueue
- Framedone-work is never ran, as the shared workqueue is blocked. This
  means that the unblank thread stays blocked, which means that context 2
  stays blocked.

While I think the real problem is in keyboard/virtual terminal code, using
a private workqueue in the DSI driver is perhaps safer and more robust
than using the shared one. The DSI works should not be delayed more than a
millisecond or so, and even if the private workqueue gives us no hard
promise of doing so, it's still safer bet than the shared workqueue.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

dsi_vc_flush_receive_data() is meant to dump data when something has gone
wrong, and thus we should use DSSERR, not DSSDBG.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

For some reason screen updates of certain odd widths seem to be triggering
HS TX timeouts on OMAP 3430, even if bigger updates do not. The reason for
this is unknown, but increasing the timeout removes the problem with no
(so far) noticeable problems. I haven't seen this problem on OMAP 3630.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

Add error printing for dsi_vc_dcs_write() and dsi_vc_dcs_read().
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

Add dsi_vc_dcs_read_2() helper function to read two bytes from the DSI
peripheral.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

With the reworked model, DSI driver doesn't need to know anything about
external TE lines. Thus we can remove ext_te support, and only leave the
DSI TE trigger support.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

Move enable/disable/suspend/resume from omap_dss_device to
omap_dss_driver.

This is part of a larger patch-set, which moves the control from omapdss
driver to the display driver.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

Move update() and sync() from omap_dss_device to omap_dss_driver.

Also, update was hardcoded to use virtual channel 0. This patch adds a
parameter that specifies the VC.

This is part of a larger patch-set, which moves the control from omapdss
driver to the display driver.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

Move set/get_update_mode() from omap_dss_device to omap_dss_driver.

This is part of a larger patch-set, which moves the control from omapdss
driver to the display driver.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

Move enable/get_te() from omap_dss_device to omap_dss_driver.

This is part of a larger patch-set, which moves the control from omapdss
driver to the display driver.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

Move get_resolution() from omap_dss_device to omap_dss_driver.

This is part of a larger patch-set, which moves the control from omapdss
driver to the display driver.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

Move enable/disable_channel() from omap_dss_device to overlay manager.

This is part of a larger patch-set, which moves the control from omapdss
driver to the display driver.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

Move get/set_rotate() from omap_dss_device to omap_dss_driver.

This is part of a larger patch-set, which moves the control from omapdss
driver to the display driver.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

Move set/get_mirror() from omap_dss_device to omap_dss_driver.

This is part of a larger patch-set, which moves the control from omapdss
driver to the display driver.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

Move memory_read() from omap_dss_device to omap_dss_driver.

This is part of a larger patch-set, which moves the control from omapdss
driver to the display driver.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

Move run_test() from omap_dss_device to omap_dss_driver.

This is part of a larger patch-set, which moves the control from omapdss
driver to the display driver.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

Remove performance measurement for auto-update. Auto-update and thus
performance measurement cannot be supported after the driver change where
the control is moved to display drivers.

This is part of a larger patch-set, which moves the control from omapdss
driver to the display driver.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

Physical DSI bus is protected by a mutex. This patch changed the mutex to
a semaphore, so that we can lock and unlock the bus_lock from different
threads.

This is needed as the update process is started by user space program, and
thus the lock is acquired in that context, but the lock can be released in
different context, a work thread via irq.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

After changing the selection of DSI and DISPC clock source the users of
get_dsi/dispc_clk_source() functions were left unchanged.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>