提交 e406f907 编写于 作者: T Tomi Valkeinen

OMAP: DSS2: DSI: Wait for DSI PLL clocks to be active before selecting them

The TRM tells us to wait for the DSI PLL derived clocks to become
active before selecting them for use. I didn't actually have any issues
which this would fix but according to the TRM it seems to be the right
thing to do.
Signed-off-by: NVille Syrjälä <ville.syrjala@nokia.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>
上级 ebf0a3fe
......@@ -3195,6 +3195,18 @@ int dsi_init_display(struct omap_dss_device *dssdev)
return 0;
}
void dsi_wait_dsi1_pll_active(void)
{
if (wait_for_bit_change(DSI_PLL_STATUS, 7, 1) != 1)
DSSERR("DSI1 PLL clock not active\n");
}
void dsi_wait_dsi2_pll_active(void)
{
if (wait_for_bit_change(DSI_PLL_STATUS, 8, 1) != 1)
DSSERR("DSI2 PLL clock not active\n");
}
int dsi_init(struct platform_device *pdev)
{
u32 rev;
......
......@@ -265,6 +265,9 @@ void dss_select_dispc_clk_source(enum dss_clk_source clk_src)
b = clk_src == DSS_SRC_DSS1_ALWON_FCLK ? 0 : 1;
if (clk_src == DSS_SRC_DSI1_PLL_FCLK)
dsi_wait_dsi1_pll_active();
REG_FLD_MOD(DSS_CONTROL, b, 0, 0); /* DISPC_CLK_SWITCH */
dss.dispc_clk_source = clk_src;
......@@ -279,6 +282,9 @@ void dss_select_dsi_clk_source(enum dss_clk_source clk_src)
b = clk_src == DSS_SRC_DSS1_ALWON_FCLK ? 0 : 1;
if (clk_src == DSS_SRC_DSI2_PLL_FCLK)
dsi_wait_dsi2_pll_active();
REG_FLD_MOD(DSS_CONTROL, b, 1, 1); /* DSI_CLK_SWITCH */
dss.dsi_clk_source = clk_src;
......
......@@ -281,6 +281,8 @@ void dsi_pll_uninit(void);
void dsi_get_overlay_fifo_thresholds(enum omap_plane plane,
u32 fifo_size, enum omap_burst_size *burst_size,
u32 *fifo_low, u32 *fifo_high);
void dsi_wait_dsi1_pll_active(void);
void dsi_wait_dsi2_pll_active(void);
#else
static inline int dsi_init(struct platform_device *pdev)
{
......@@ -289,6 +291,12 @@ static inline int dsi_init(struct platform_device *pdev)
static inline void dsi_exit(void)
{
}
static inline void dsi_wait_dsi1_pll_active(void)
{
}
static inline void dsi_wait_dsi2_pll_active(void)
{
}
#endif
/* DPI */
......
Markdown is supported
0% .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑!
想要评论请 注册