Remove the -2.6 from the name.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org

Since there is no current software control for these they would otherwise
be left enabled, consuming power.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org

The WM8962 has a separate software reset for the PLL registers. Ensure that
these are reset also on startup.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org

We can't just pass back the return value of snd_soc_update_bits() as it
will be 1 if a bit changed rather than zero.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Set `invert' bit for Capture Switch. Otherwise analogue is muted when
Capture Switch is ON.
Signed-off-by: NHong Xu <hong.xu@atmel.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org

Current implementation in wm8711_set_dai_fmt always clear BIT[3:2]
(the Input Audio Data Bit Length Select) of WM8711_IFACE(07h) register.
Input Audio Data Bit Length Select bits are set by wm8711_hw_params,
we should leave BIT[3:2] untouched in wm8711_set_dai_fmt.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org

The Input Audio Data Bit Length Select is controlled by BIT[3:2] of
WM8711_IFACE(07h) register.
Current code incorrectly masks BIT[1:0] which is for Audio Data Format Select.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org

According to the datasheet:

Page0 / Register8: Audio Serial Data interface Control Register A
BIT 7: Bit Clock Directional Control
        0: Bit clock is an input (slave mode)
        1: Bit clock is an output (master mode)

BIT 6: Word Clock Directional Control
        0: Word clock is an input (slave mode)
        1: Word clock is an output (master mode)

Current code sets BIT_CLK_MASTER and WORD_CLK_MASTER bits for master mode,
but does not clear these bits for slave mode.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

According to the datasheet:

Digital Audio Interface Format (07h) register:
BIT6:	Master/slave mode
	0: Slave
	1: Master

Current code sets TLV320AIC23_MS_MASTER bit for master mode,
but does not clear it for slave mode.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

According to the datasheet:
BCLK is controlled by BIT[4:2] of WM8940_CLOCK(06h) register.
Signed-off-by: NChris Paulson-Ellis <chris@edesix.com>
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Reported-by: NChris Paulson-Ellis <chris@edesix.com>
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org

codec->hw_write is broken now, convert codec->hw_write to snd_soc_write.

The hardware has 2 banks of registers sharing a section in I2C register space.
The 1st bank is the primary one and is cached.
The 2nd bank is for loading coefficients only and they do not need cache.
These coefficients registers are therefore direct writes.
Thus we set cache_bypass flag to deal with this before calling snd_soc_write.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Acked-by: NLiam Girdwood <lrg@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Add a new variable for storing resources accessed subsequent to the one
accessed using request_mem_region, so the one accessed using
request_mem_region can be released if needed.

The resource variable names are also changed to be more descriptive.

This code is also missing some calls to iounmap.

The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@r@
expression E, E1;
identifier f;
statement S1,S2,S3;
@@

if (E == NULL)
{
  ... when != if (E == NULL || ...) S1 else S2
      when != E = E1
*E->f
  ... when any
  return ...;
}
else S3
// </smpl>
Signed-off-by: NJulia Lawall <julia@diku.dk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Ensure all mask bits are clear before setting new value.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Acked-by: NDong Aisheng <b29396@freescale.com>
Acked-by: NLiam Girdwood <lrg@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Acked-by: NLiam Girdwood <lrg@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org

DA7210 has three line outputs. OUT1 Left, OUT1 Right and OUT2 (mono).
This patch adds support for gain controls for these three line outs.
It also adds support for overall DAC gain control.
Signed-off-by: NAshish Chavan <ashish.chavan@kpitcummins.com>
Signed-off-by: NDavid Dajun Chen <dchen@diasemi.com>
Acked-by: NLiam Girdwood <lrg@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

This patch adds support for DAPM covering all inputs and outputs
as well as ADC and DAC.
Signed-off-by: NAshish Chavan <ashish.chavan@kpitcummins.com>
Signed-off-by: NDavid Dajun Chen <dchen@diasemi.com>
Acked-by: NLiam Girdwood <lrg@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

We have defined SGTL5000_LINREG_VDDD_MASK in sgtl5000.h,
use it instead of hardcoded (0x1 << 4) - 1 for the mask.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Acked-by: NWolfram Sang <w.sang@pengutronix.de>
Acked-by: NLiam Girdwood <lrg@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Otherwise calling ldo_regulator_remove() does not unregister regulator
and free memories.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Acked-by: NWolfram Sang <w.sang@pengutronix.de>
Acked-by: NLiam Girdwood <lrg@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Acked-by: NLiam Girdwood <lrg@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org

Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Acked-by: NLiam Girdwood <lrg@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org

Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Acked-by: NLiam Girdwood <lrg@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Use snd_soc_update_bits for read-modify-write register access instead of
open-coding it using snd_soc_read and snd_soc_write
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Acked-by: NLiam Girdwood <lrg@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

According to the register map in datasheet, the registers are 8 bit.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Acked-by: NLiam Girdwood <lrg@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

According to the datasheet:
BIT 2:1
        VMID_SEL[1:0] VMID Divider Enable and Select
        00 = VMID disabled
        01 = 2x40k Omh divider
        10 = 2x240k Omh divider
        11 = 2x5k Omh divider

To set VMID 2*240k, we should OR reg with 0x04 instead of 0x40.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Acked-by: NLiam Girdwood <lrg@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Acked-by: NLiam Girdwood <lrg@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

This patch adds controls to set following ALC parameters,
 - Max gain, Min gain, Noise gain, Attack rate, Release rate and delay

It also adds a switch to enable/disable noise suppression.

As per DA7210 data sheet, ALC and noise suppression can be enabled
only if certain conditions are met. This condition checks are handled
by simply using "_EXT" version of controls to capture change events.
Signed-off-by: NAshish Chavan <ashish.chavan@kpitcummins.com>
Signed-off-by: NDavid Dajun Chen <dchen@diasemi.com>
Acked-by: NLiam Girdwod <lrg@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

This patch adds support for below set of controls,
(1) Mute controls for MIC, AUX and ADC
(2) Zero cross controls for head phone, AUX, INPGA and line out
(3) Head phone mode selection - class H or G

It also adds digital_mute() call back.
Signed-off-by: NAshish Chavan <ashish.chavan@kpitcummins.com>
Signed-off-by: NDavid Dajun Chen <dchen@diasemi.com>
Acked-by: NLiam Girdwood <lrg@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Acked-by: NLiam Girdwood <lrg@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Use snd_soc_update_bits for read-modify-write register access instead of
open-coding it using snd_soc_read and snd_soc_write
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Acked-by: NLars-Peter Clausen <lars@metafoo.de>
Acked-by: NLiam Girdwood <lrg@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Not that we have interrupt handling in the driver at the minute.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@ti.com>

According to the datasheet:
CHIP_MIC_CTRL 0x002A

BITS[9:8] BIAS_RESISTOR
        0x0 = Powerd off
        0x1 = 2.0 kohm
        0x2 = 4.0 kohm
        0x3 = 8.0 kohm

To set mic bias resistor, we need to update bits[9:8] of
SGTL5000_CHIP_MIC_CTRL register.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Acked-by: NWolfram Sang <w.sang@pengutronix.de>
Acked-by: NLiam Girdwood <lrg@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

According to the datasheet:
CHIP_MIC_CTRL 0x002A

BITS[9:8] BIAS_RESISTOR
        0x0 = Powerd off
        0x1 = 2.0 kohm
        0x2 = 4.0 kohm
        0x3 = 8.0 kohm

Thus SGTL5000_BIAS_R_MASK should be defined as 0x0300 instead of 0x0200.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Acked-by: NWolfram Sang <w.sang@pengutronix.de>
Acked-by: NLiam Girdwood <lrg@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Use snd_soc_update_bits for read-modify-write register access instead of
open-coding it using snd_soc_read and snd_soc_write
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Acked-by: NLars-Peter Clausen <lars@metafoo.de>
Acked-by: NBarry Song <21cnbao@gmail.com>
Acked-by: NLiam Girdwood <lrg@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

We don't want to clear the prefix while we're creating the DAPM controls
for the device as the prefix is applied during control creation.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@ti.com>

At least for the core controls, the optionally selected controls are still
added programatically.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@ti.com>

Evaluation of larger quantities of material has provided new DCS codes
values to be applied for WM1811.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@ti.com>

Use snd_soc_update_bits for read-modify-write register access instead of
open-coding it using snd_soc_read and snd_soc_write
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Use snd_soc_update_bits for read-modify-write register access instead of
open-coding it using snd_soc_read and snd_soc_write
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>