Add support for st6422 bridge and sensor to the stv06xx gspca sub driver,
tested with:
Logitech QuickCam Messenger     046d:08f0       ST6422  integrated
Logitech QuickCam Mess. Plus    046d:08f6       ST6422  integrated
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

gspca_ov519: Cleanup some sensor special cases
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

gspca_ov519: Fix ov518+ with OV7620AE (Trust spacecam 320)
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

gspca_ov519: add support for the ov511 bridge
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Hmm, another one with an extra if (life sucks) the
default contrast really is no good for the ov6630, it
isn't even high enough in full daylight, this gives
the ov6630 a different initial value for a better out
of the box experience.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

As reported on the ov51x-jpeg list, and as I can confirm with my own cam
the ov7670 in 320x240 has a number of broken columns of pixels
at the left of the picture. This was not present in the old
driver as it always used 640x480 and did software
downscaling (took me a while to figure that one out).
The fix adds a sensor specific if in so far sensor
neutral code :( But this is the only way to fix this,
this cannot be fixed by only changing sensor registers.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

My ov519 cam has it led inverted, the same has been
reported on the ov51x-jpeg list for another
creative cam. This patch fixes this without changing
the behaviour for other cams.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Check ov518 packet numbers to detect dropped packets.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

gspca_ov519: Add 320x240 and 160x120 support for cif sensor cams
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The fix for the UV swapping in qcif mode with the ov6630, which I did
to fix this issue on a ov518 cam with an ov66308AF, causes UV swapping in
qcif with another cam of mine with the ov518 and an ov66308AE, so this
patch changes the code to differentiate between the ov66308AF and other
ov6630 versions, and restricts the UV swap fix to the ov66308AF.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This patch adds autobrightness (so that it can
be turned off to make the already present brightness
control work) and light frequency filtering controls.

The lightfreq control needed 2 different entries
in the ctrls array, as the number of options differs
depending on the sensor. Always one of the 2 entires is
disabled ofcourse.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

gspca: fix NULL pointer deref in query_ctrl
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Fix Leadtek TV2000 XP Global entries and add missing PCI ID's.

Thanks to Terry Wu <terrywu2009@gmail.com> for pointing us for the proper settings.

Cc: Terry Wu <terrywu2009@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Unify i2c camera device platform data to point to struct soc_camera_link
for a smooth transition to soc-camera as a platform driver.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Since videobuf-dma-contig is designed to handle physically contiguous
memory, this patch modifies the videobuf-dma-contig code to only accept a
user space pointer to physically contiguous memory.  For now only
VM_PFNMAP vmas are supported, so forget hotplug.

On SuperH Mobile we use this with our sh_mobile_ceu_camera driver together
with various multimedia accelerator blocks that are exported to user space
using UIO.  The UIO kernel code exports physically contiguous memory to
user space and lets the user space application mmap() this memory and pass
a pointer using the USERPTR interface for V4L2 zero copy operation.

With this approach we support zero copy capture, hardware scaling and
various forms of hardware encoding and decoding.

[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Acked-by: NMauro Carvalho Chehab <mchehab@infradead.org>
Cc: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NJean-Francois Moine <moinejf@free.fr>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

bttv-driver.c,cx23885-video.c,cx88-video.c: poll method lose race condition for capture video.
Signed-off-by: NFigo.zhang <figo1802@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

cx88-dsp: fixing 64bit math on 32bit kernels

Some gcc versions report the missing of __divdi3

[mchehab.redhat.com: CodingStyle fixes]
Signed-off-by: NMiroslav Sustek <sustmidown@centrum.cz>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This patch changes cx88_set_stereo to avoid resetting all of the audio
registers on stereo/mono change if the audio standard is A2, and set
only the AUD_CTL register. The benefit of this method is that it
eliminates the annoying clicking noise on setting the audio mode to
stereo or mono.

The driver had used the same method 1.5 years ago (and for FM radio it
still does), but a pretty big cleanup commit changed it to the
"complete audio reset" method, although the reason for this move was
not clear. (If somebody knows why it was necessary, please let me
know!)

The original commit: http://linuxtv.org/hg/v4l-dvb/rev/ffe313541d7dSigned-off-by: NMarton Balint <cus@fazekas.hu>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The sole purpose of the audio thread is to detect if stereo transmission is
available, and if it is, then switch to stereo mode (and switch back, if it's
no longer available). This manual autodetection is useful for some audio
standards (e.g. A2) where cx88_get_stereo CAN detect stereo sound, but the
cx2388x chip CANNOT auto-detect stereo sound.

However, for other audio standards, the cx2388x chip CAN auto-detect the stereo
sound, so the manual autodetection in the audio thread is not needed. In fact,
it can cause serious problems because for some of these audio standards,
cx88_get_stereo CANNOT detect the presence of stereo sound.  Besides that, if
the hardware automatically detects stereo/mono sound, you cannot set
core->audiomode_current to the real current audio mode on channel change.

With this patch, the manual autodetection is only used if audiomode_current is
known after a channel change (because of the initial mono mode), and
hardware-based stereo autodetecion is not applicable for the current audio
standard.
Signed-off-by: NMarton Balint <cus@fazekas.hu>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The patch implements reliable stereo and sap detection for the A2 sound
standard.  This is achieved by processing the samples of the audio RDS fifo of
the cx2388x chip. A2M, EIAJ and BTSC stereo/sap detection is also possible with
this new approach, but it's not implemented yet. Stereo detection when alsa
handles the sound also does not work yet.
Signed-off-by: NMarton Balint <cus@fazekas.hu>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

A power management fix to properly put the xc5000 into low power mode
revealed a race condition where hald could detect the creation of the device
file and connect to the device while the initial device configuration is
still in progress.

Lock the core structure so that video_release cannot be called and put the
tuner to sleep in the middle of the initial call to cx88_set_tvnorm() in
cx8800_initdev()

Thanks to Michael Krufky for discovering the issue and providing an
environment to test in.

Cc: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Error count in read pipe completion corrected.
URB not resubmitted if shutting down.
URB not freed in completion routine if new urb_submit_fails.
(URB is freed on shutdown).
Signed-off-by: NDean Anderson <dean@sensoray.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (12002): uvc: Fix for no return value check of uvc_ctrl_set() which calls mutex_lock_interruptible()

Fix for no return value check of uvc_ctrl_set() which calls
mutex_lock_interruptible().
Signed-off-by: NRobert Krakora <rob.krakora@messagenetsystems.com>
Acked-by: NLaurent Pinchart <laurent.pinchart@skynet.be>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Having fixed the sprintfs I decided a quick clean wouldn't do any harm so
it was actually easy to read in future.
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Patch removes needless if check and goto.
Signed-off-by: NAlexey Klimov <klimov.linux@gmail.com>
Reviewed-by: NErik Andrén <erik.andren@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Add 1461:f736 to the list of identifiers corresponding to the
SAA7134_BOARD_AVERMEDIA_M103 board.  This patch adds support for
a variant of the AVerMedia M103 MiniPCI DVB-T Hybrid card.
Signed-off-by: NBarry Kitson <b.kitson@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

vfree() does it's own NULL checking, no need for explicit check before
calling it.
Signed-off-by: NFigo.zhang <figo1802@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The current code creates a sysfs device path where the video4linux
device is child of the usb device itself instead of the interface it
belongs to. That is evil and confuses udev.

This patch does basically the same thing as Kay's similar patch for the
ov511 driver:

at git commit ce96d0a4Signed-off-by: NLennart Poettering <mzxreary@0pointer.de>
Acked-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Add missing __devexit_p() to several drivers. Also add a few missing
__init, __devinit and __exit markers. These errors could result in
build failures depending on the kernel configuration.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

add poiter check for videobuf_queue_core_init().

any guys who write a v4l driver, pass a NULL pointer or a non-inintial
pointer to the first parameter such as videobuf_queue_sg_init() , it
would be crashed.
Signed-off-by: NFigo.zhang <figo1802@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

when re-open or re-start (video_streamon), the q->curr would not be NULL in saa7134_buffer_queue(),
and all the qbuf will add to q->queue list,no one to do activate to start DMA,and then no interrupt
would happened,so it will be block.

In VIDEOBUF_NEEDS_INIT state, initialize the curr pointer to be NULL in the buffer_prepare().
Signed-off-by: NFigo.zhang <figo.zhang@kolorific.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

In cases where the device does not actually provide a USB audio class *or*
vendor audio, do not load the driver that provides vendor audio support (such
as the KWorld 2800d).  Otherwise, the /dev/audio1 device file gets created and
users get confused.

Also, reworks the logic a bit so that we don't try to inspect the register
content if the register read failed entirely.
Signed-off-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Added an entry for Kworld 315 (for while, dvb only)
Signed-off-by: NFranklin Meng <fmeng2002@yahoo.com>
Signed-off-by: NDouglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Added tda9887_conf set up into em28xx_card_setup()
Signed-off-by: NFranklin Meng <fmeng2002@yahoo.com>
Signed-off-by: NDouglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The scan of the image packets of the sensor ov772x was broken when
the sensor ov965x was added.
Signed-off-by: NJean-Francois Moine <moinejf@free.fr>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NJean-Francois Moine <moinejf@free.fr>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NJean-Francois Moine <moinejf@free.fr>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NJean-Francois Moine <moinejf@free.fr>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Since i2c autoprobing is no longer supported by v4l2 we need to make sure
that the i2c modules are linked before the v4l2 modules. The v4l2 modules
now rely on the presence of the i2c modules, so these must have initialized
themselves before the v4l2 modules.

The exception is the ir-kbd-i2c module, which is the only one still using
autoprobing. This one should be loaded at the end of the v4l2 module. Loading
it earlier actually causes problems with tveeprom. Once ir-kbd-i2c is no
longer autoprobing, then it has to move up as well.

This is only an issue when everything is compiled into the kernel.

Thanks to Marcus Swoboda for reporting this and Udo Steinberg for testing
this patch.
Tested-by: NUdo A. Steinberg <udo@hypervisor.org>
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>